when did the detonation occurs in a reciprocating aircraft engine?
Answers
The detonation occurs in a reciprocating aircraft engine when the air-fuel mixture in the combustion chamber detonates or explodes rather than burning smoothly and evenly.
What is detonation?Detonation is a type of combustion in which a supersonic shock wave propagates through a fluid as a result of energy release in a reaction zone.
Detonation can occur at any time during engine operation, but it is more likely to occur under high temperature, high pressure, and high engine load conditions.
It's also more likely to happen if the fuel has a low octane rating or if the air-fuel mixture is too lean.
Detonation can cause knocking or pinging sound in the engine and can lead to damage such as cracked pistons or burned valves.
To prevent detonation, pilots and mechanics must ensure that the engine is operating within its recommended parameters and that the fuel being used has a sufficient octane rating.
Thus, this time detonation occurs in a reciprocating aircraft engine.
For more details regarding detonation, visit:
https://brainly.com/question/12748977
#SPJ1
Related Questions
A weld symbol below the reference line signifies a weld on the "ARROW" side of the joint.
Answers
requires a mix of machines, equipment, energy and labor
Answers
Answer:
building?
Explanation:
Which of the following is NOT a risky food:
a
Raw Meat
b
Uncleaned fruits & vegetables
c
Bread
d
All of the above
e
Soft Cheeses
Answers
i think it's c. bread.
Answer:I think raw meat because if you eat raw meat you get sick and get stomach aches so always when you cook meat it kill the bacteria
Explanation:what I'm trying to says is stay safe
a caisson is a watertight enclosure that can be pumped dry so that construction activities, such as the construction of piers can take place. _______
Answers
A caisson is a watertight enclosure that can be pumped dry so that construction activities, such as the construction of piers can take place. A caisson is a watertight structure or chamber, usually made of wood, metal, or concrete, that is sunk to the bed of a river, lake, or ocean to provide a foundation or support for a bridge, building, or other structure.
A caisson is constructed onshore and then floated to the location where it is to be sunk into the water. Once in place, water is pumped out of the caisson, and construction workers enter the dry chamber to begin work on the foundation or support structure. The use of caissons has been an important development in the construction of bridges and other structures in areas with deep water or unstable soils.
A foundation called a caisson is used in construction on soft or deep water. It involves filling a series of large, watertight cylinders with concrete and sinking them into the ground. The base serves as a solid foundation for any subsequent structures. The construction of large structures like bridges, docks, and caissons is common.
Know more about caisson, here:
https://brainly.com/question/16249983
#SPJ11
will give brainliest what are 3 good projects to do with wood or cardboard or paper or an old drone when you are a beginner
if you do not have 3 good projects then please dont answer and just comment them but if you have more than 3 that would be great for you to answer.
Answers
1. A simple wall shelf
2. Cup holder
3. Candle holder
Hope this helps!
Answer:the inflating Ballon expirement
Explanation:
For this activity, imagine you are participating in a town hall meeting about possible gene drive research. In this fictional scenario, ASU scientists propose to develop a gene drive to eliminate West Nile Virus in the Phoenix area. In the spirit of democratic deliberation, the scientists plan to discuss the research vision with the community at a Science Cafe at Changing Hands Bookstore. Select one of the meeting participants to play from the list below. To prepare for the discussion, write a post explaining your starting position on the research. Are you in favor? Have questions? Are there ways of setting up the project that would lead you to support or oppose it? Etc.Participants:
A Tempe city council member
A retiree who has recently moved to Arizona to be near kids
A stay-at-home parent with young children
A local hardware store employee
Answers
As a local hardware store employee, I have concerns about the long-term consequences and risks of a gene drive for eliminating West Nile Virus.
Participant: A local hardware store employee
Post:
As a local hardware store employee, I have a vested interest in the well-being of the Phoenix community. I understand that the scientists from ASU are proposing the development of a gene drive to eliminate West Nile Virus in our area, and I believe it's crucial to have an open discussion about this research vision.
Firstly, I want to emphasize that I am not an expert in genetics or public health. However, I do have concerns and questions regarding the potential implementation of a gene drive for such a purpose.
My main concern revolves around the long-term consequences and potential risks associated with altering the genetic makeup of organisms, even if it is for a positive outcome like eliminating West Nile Virus. While the eradication of this disease is undoubtedly a worthy goal, we must ensure that the benefits outweigh any unintended negative effects.
Before I can fully support or oppose this research, I would like to better understand the safeguards that would be put in place to prevent any unintended ecological disruptions. What are the contingency plans if the gene drive were to have unintended consequences on non-target species? Are there measures in place to address potential resistance to the gene drive in the West Nile Virus-carrying mosquitoes? These are critical questions that must be answered to assess the feasibility and safety of this project.
Additionally, it would be crucial to involve a diverse range of stakeholders in the decision-making process. Engaging with experts in genetics, public health officials, and environmentalists, along with community members, will help ensure that all perspectives are taken into account. Transparency and inclusivity are key to fostering trust and ensuring that the decision ultimately made serves the best interests of our community.
In conclusion, while I recognize the importance of addressing the issue of West Nile Virus, I approach the proposal for a gene drive with caution. My starting position is one of skepticism and the need for further information. I believe a comprehensive risk assessment, robust stakeholder engagement, and a thorough examination of potential unintended consequences are necessary before making a final determination on supporting or opposing the project.
Learn more about Gene drive
brainly.com/question/30243090
#SPJ11
(a) calculate the required steam feed rate (kg/h) for a slurry feed rate of 1:00 103 kg/h. (b) vapor recompression is often used in the operation of an evaporator. suppose that the vapor (steam) generated in the evaporator described above is compressed to 2.6 bar and simultaneously heated to the saturation temperature at 2.6 bar, so that no condensation occurs. the compressed steam and additional saturated steam at 2.6 bar are then fed to the evaporator coil, in which isobaric condensation occurs. how much additional steam is required? (c) what more would you need to know to determine whether or not vapor recompression is economically advantageous in this process?
Answers
(a)
To calculate the required steam feed rate for a slurry feed rate of 1:00 103 kg/h, we need to know the heat transfer rate of the evaporator, as well as the heat of vaporization of the liquid being evaporated. Using these values, we can determine the amount of heat energy required to evaporate the slurry and then use the steam tables to find the corresponding steam flow rate.(b)
Vapor re compression is a method of improving the efficiency of an evaporator by recycling the steam produced during the process. In this case, the compressed steam and additional saturated steam at 2.6 bar are used to feed the evaporator coil, in which isobaric condensation occurs. To determine how much additional steam is required, we would need to know the heat transfer rate of the evaporator and the heat of vaporization of the liquid being evaporated, as well as the specific heat of the compressed steam and the additional saturated steam.
(c)
For such more question on condensation
https://brainly.com/question/30629848
#SPJ11
Write an Essay describing in your own words, the two-way Communication Cycle naming all the stages and explaining what goes on at each stage. Illustrate any two barriers that may occur at each of the stages. A correctly labelled diagram is essential for your essay.
Answers
n
e
g
r
o
means black in spanish!
Recycling is being discussed. Technician A says that automotive batteries can be recycled and the materials used to make new batteries. Technician B says that batteries cannot be recycled because they contain acid, lead and other toxic materials Who is right?
Answers
Technician A is correct because the automotive batteries can be recycled and the materials used to make new batteries.
Materials present in the battery;
lead and other toxic materialsLead-acid batteries are used to store chemical energies and they are highly recyclable.
To recycle a lead-acid battery, first step is to break it into smaller fragments such as lead, plastic coating and the toxic material (sulfuric acid).
The lead and the plastic coating will be recycled into new batteriesThe toxic material (sulfuric acid) will be neutralized and converted into sodium sulfate. This sodium sulfate can be used to make fertilizer and detergent.Thus, we can conclude that Technician A is correct because the automotive batteries can be recycled and the materials used to make new batteries.
Learn more here: https://brainly.com/question/14970088
Does anyone know the answer to this
Answers
Answer:
A
Explanation:
Answer:
A
Explanation:
The fuse breaks the circuit if a fault in an appliance causes too much current to flow. The fuse contains a piece of wire that melts easily. If the current going through the fuse is too great,the wire heats up until it melts and breaks the circuit
What is not a duty of a general service technician?
Answers
Order the parts needed is NOT a duty of the General Service Technician.
General service technicians are knowledgeable workers who are in charge of carrying out repair tasks on cars and other light vehicles. Customers must interact with these specialists in order to discuss pricing estimates for undertaking car maintenance services. They are required to undertake any required repairs or part replacements as well as visual vehicle inspections. They must possess the necessary skills to operate equipment that mounts and balances vehicle tyres. General service personnel should be able to install car batteries and inspect the electrical systems of vehicles.
Therefore, order the parts needed is NOT a duty of the General Service Technician.
Learn more about the general service technician here:
https://brainly.com/question/28540275.
#SPJ6
a step-up transformer is designed to have an output voltage of 2 200 v (rms) when the primary is connected across a 110-v (rms) source. (a) if the primary winding has exactly 84 turns, how many turns are required on the secondary? turns (b) if a load resistor across the secondary draws a current of 1.80 a, what is the current in the primary, assuming ideal conditions? a (c) if the transformer actually has an efficiency of 89.0%, what is the current in the primary when the secondary current is 1.20 a? a
Answers
The number of turns required on the secondary is 1,680. The current in the primary is 22.9 A.
What is step-up transformer?A step-up transformer is a device that increases the voltage of an AC power supply. It works by having more turns in the secondary coil than the primary coil, allowing it to convert low voltage to high voltage.
a) The ratio of the number of turns in the primary winding to the number of turns in the secondary winding of a transformer is equal to the ratio of the output voltage to the input voltage.
N₂/N₁ = V₂/V₁
Plugging in the given values, we get:
N₂/84 = 2,200/110
N₂ = 84 x 2,200/110
N₂ = 1,680 tu
b) In an ideal transformer, the power is conserved, so the product of the primary current and the primary voltage is equal to the product of the secondary current and the secondary voltage. That is:
I₁V₁ = I₂V₂
We can rearrange this equation to solve for the primary current:
I₁ = (I₂V₂)/V₁
Plugging in the given values, we get:
I₁ = (1.80 A x 2,200 V)/110 V
I₁ = 36 A
The current in the primary is 36 A.
c) The efficiency of a transformer is given by the ratio of the output power to the input power. That is:
efficiency = output power / input power
P₁ = V₁I₁
We can use the efficiency formula to calculate the output power:
efficiency = output power / (output power + power loss)
output power + power loss = output power / efficiency
= (V₂I₂)² / V₁I₁ / 0.89
power loss = output power - (output power / efficiency)
= (V₂I₂)² / V₁I₁ / 0.89 - (V₂I₂)² / V₁I₁
Now we can use the power formulas to solve for the primary current:
P₁ = P₂ / efficiency
V₁I₁ = (V₂I₂) / 0.89
I₁ = (V₂I₂ / 0.89) / V₁
Plugging in the given values, we get:
I₁ = (2,200 V x 1.20 A / 0.89) / 110 V
I₁ = 22.9 A
To know more about power visit:
brainly.com/question/13357691
#SPJ4
Step 1: Build the Board 1. Build an empty 8 x 8 board (call the Game Board array GB ) filled with zeros. (You must use the zeros command for this). 2. For your board we will assume that a value of 0 in that space means no boat there and a 1 means a boat is hidden there. 3. Use a FOR loop to control placing your Rowboats on the board. THINK ABOUT IT before you start writing code. It may take more than 6 attempts to place your 6 Rowboats because some spaces may be randomly picked more than once. So, you need a FOR loop with a very large number of iterations such as 10000 to ensure that you have a good chance to find 6 empty spaces for the Rowboats. 4. To place each Rowboat on the board: Each row number, m, and each column number, n, is a separate random number. You are to use the random number generator randi to randomly pick a space on the board like this: m = randi(8) and n = randi(8) o Check if the space (m,n) is empty using a logical test like: GB(m,n)==0. You also need to test if you still need to place more Rowboats on the board. o If both tests are true, then change the value of that space to 1 to show that you have placed a Rowboat there. That is, GB(m,n) = 1. You may also need to keep track of how many Rowboats you have put on the board. 5. After you have placed the 6 Rowboats on your board, use the instructions below to create an image of the board showing where the 6 Rowboats are positioned. • To show the board as an image, use these three commands: imagesc(GB) % GB is the name of your array axis square' % This makes your image a square shape and corrects for screen resolution title('My Row Boat Placement") % The title I want you to use for this problem. Put your name on the label for the x-axis. (Use the xlabel command as with plots.) o DO NOT put a label on the y-axis. Add another new command called "grid on" to draw thin lines showing your Row Boat placement. Add the following 2 lines of code to add tick marks and make your board image a bit prettier: xticks (1:1:8) yticks (1:1:8) You should see 6 Rowboats on your board. Next week we begin to talk more about images, but we wanted to introduce how to make an image, like the board, in preparation for that.
Answers
To build the board, the following steps are to be followed:Build an empty 8 x 8 board filled with zeros using zeros command. Consider 0 to represent no boat while 1 to represent the presence of a boat.
To place the rowboats, use a for loop to control and perform iterations for randomly placing 6 rowboats on the board. Using the random number generator randi to randomly pick a space on the board. To place each Rowboat on the board, you have to check whether the chosen space is empty or not using a logical test like GB(m,n) == 0. After checking the chosen space, if it's empty and needs to place more rowboats, then change the value of that space to 1, i.e., GB(m,n) = 1. Keep track of how many rowboats are placed on the board. Create an image of the board using the instructions below:Use imagesc(GB) to display the image of the board. The GB is the name of the array. Use the command 'axis square' to correct the shape of the image. Use the command 'title('My Row Boat Placement")' to add the title to the image. Put your name on the label for the x-axis. Use the xlabel command as with plots. Avoid putting a label on the y-axis. Use the command "grid on" to draw thin lines showing your Row Boat placement. Use xticks (1:1:8) and yticks (1:1:8) commands to add tick marks and make your board image a bit prettier.The for building the board and placing rowboats is given below:```matlabGB=zeros(8,8); % build the empty boardcount=0;for i=1:10000 % use a very large number of iterationsm=randi(8); % randomly pick row numbern=randi(8); % randomly pick column numberif GB(m,n)==0 % check if space is emptycount=count+1; % update the countGB(m,n)=1; % place the rowboatif count==6 % check if all rowboats are placedbreak;endendendimagesc(GB)axis squaretitle('My Row Boat Placement')xlabel('Name')grid onxticks (1:1:8)yticks (1:1:8)```
To know more about code snippet visit:
https://brainly.com/question/30471072
#SPJ11
what's the primary line current for a fully loaded 45 kva, 480v to 120/240v, three-phase transformer?
Answers
The primary line current for a fully loaded 45 kVA, 480V to 120/240V, three-phase transformer is approximately 54.2 amps.
The primary line current is determined by the transformer's kVA rating and input voltage. In this case, the transformer is rated for 45 kVA and has an input voltage of 480V. To calculate the primary line current, you can use the formula:
Primary Line Current = kVA ÷ (sqrt(3) x Input Voltage)
Plugging in the values, we get:
Primary Line Current = 45,000 ÷ (sqrt(3) x 480)
Primary Line Current = 54.2 amps
Therefore, the primary line current for this transformer is approximately 54.2 amps when fully loaded.
Learn more about three-phase transformer visit:
https://brainly.com/question/31420566
#SPJ11
what does mean setbacks with MRT station?
Answers
(a) Calculate the heat flux through a sheet of steel that is 10 mm thick when the temperatures oneither side of the sheet are held constant at 300oC and 100oC, respectively.(b) Determine the heat loss per hour if the cross-sectional area of the sheet is 0.25 m2.(c) What will be the heat loss per hour if a sheet of soda-lime glass is used instead
Answers
Answer:
do the wam wam
Explanation:
The heat flux is =1038kW/m² , the heat lost per hour is =259.5 kW, the heat lost per hour using a sheet of soda- lime glass.
Calculation of heat fluxThe thickness of steel( t) = 10mm = 10× 10^-³m
The temperature difference on both sides = 300-100
∆T = 200°C
But the formula for heat flux = q = k∆T/t
Where K = thermal conductivity for steel = 51.9W/mK.
Substitute the variables into the formula for heat flux;
q = 51.9 × 200/10 × 10-³
q = 10380 × 10³/10
q = 10380000/10
q = 1038000 W/m² = 1038kW/m²
To calculate the heat lost per hour if the cross sectional area is = 0.25 m2 use the formula q × A
= 1038kW/m² × 0.25 m2
= 259.5 kW.
Learn more about heat flux here:
https://brainly.com/question/15217121
Which of the following power tools has a revolving vertical shaft and a cutter? *
1 point
a) saber saw
b) router
c) miter saw
d) circular saw
Answers
The tool that has a revolving vertical shaft and a cutter is a router. The correct option is b.
What are power tools?There are many different kinds of power tools, including portable power tools like a circular saw, heat guns, and wall chasers as well as electrical power tools like impact wrenches, lathes, power drills, power ratchet sets, and power saws.
Power tools including circular saws, jigsaws, drills, hammer drills, sanders, grinders, routers, and many others reduce labor and time requirements. The requirement for knowledge of the risks that power tools provide if used improperly is raised due to their rising use.
A power tool called a router has a flat base and a spinning blade that protrudes beyond the base. An electric motor or a pneumatic motor can drive the spindle.
Therefore, the correct option is b) router.
To learn more about power tools, refer to the link:
https://brainly.com/question/30115428
#SPJ6
What are the similarities to Native American building types?
Why is Dogon Architecture so special?
Answers
Dogon Architecture is special due to its unique blend of craftsmanship, symbolism, and preservation of cultural heritage. Similarities to Native American building types include a connection to nature, and incorporation of cultural and spiritual elements.
Similarities to Native American building types can be found in various aspects. Both Native American and Dogon architecture exhibit a strong connection to nature and the surrounding environment. They often utilize natural materials like wood, stone, and earth to construct their buildings. Additionally, both architectural styles incorporate unique cultural and spiritual elements, reflecting the beliefs and traditions of their respective communities.
Dogon Architecture is special for several reasons. Firstly, it showcases remarkable craftsmanship and architectural ingenuity. The Dogon people, residing in Mali, West Africa, have constructed their dwellings and granaries into the cliffs of the Bandiagara Escarpment for centuries, demonstrating their exceptional mastery of blending architecture with the natural landscape.
Secondly, Dogon Architecture is renowned for its symbolic significance. The structures are designed to reflect Dogon cosmology, with each building representing different spiritual and social aspects of their society. For example, the Togu Na, a communal meeting house, serves as a space for important gatherings and ceremonies, embodying the unity and cohesion of the Dogon community.
Lastly, Dogon Architecture preserves and honors the rich cultural heritage of the Dogon people. The intricate designs, elaborate carvings, and decorative motifs seen in their buildings not only serve practical purposes but also serve as visual expressions of their cultural identity and traditions. The architecture serves as a tangible link to their history, helping to maintain their cultural continuity and sense of belonging.
Overall, Dogon Architecture stands out for its harmonious integration with the environment, symbolic significance, and preservation of cultural heritage, making it a truly special and remarkable architectural style.
Learn more about Native American
brainly.com/question/14328969
#SPJ11
Database permissions are usually assigned to groups not individuals. Which of the following is the name for these groups? cursors groupings roles objects
Answers
Roles are named groups of privileges that are assigned to users or other roles in a database management system
What is a database management system?In most modern database management systems (DBMS), roles are used to simplify security management and improve the flexibility of access control. Roles are named collections of privileges that can be granted to users or other roles. Permissions can be granted to roles, and then the roles can be granted to users or other roles. This allows for a more centralized and efficient way to manage permissions for large numbers of users or objects in a database.
Roles can be used to group users with similar responsibilities or levels of access. For example, a database administrator might create roles such as "manager", "developer", and "guest" to represent different levels of access to the database. Permissions can be assigned to each role based on the needs of the users who are members of that role. Users can then be assigned to one or more roles, giving them the privileges associated with those roles.
Roles can also be used to manage access to objects within a database. For example, a role could be created to control access to a specific table or schema. Permissions can be assigned to the role to control access to the object, and then users can be assigned to the role to grant them the necessary access.
In summary, roles are named groups of privileges that are assigned to users or other roles in a database management system. They simplify security management by allowing permissions to be managed at a higher level of abstraction and provide a flexible way to manage access control to objects within a database.
Learn more about database management systems
brainly.com/question/1578835
#SPJ11
If your job involves developing rehabilitation programs for violent criminals, which of the following career pathways might you be following?
Answers
The professional path you may be taking is career pathways if your employment include creating rehabilitation programs for violent offenders. Therefore, choice B is the best one.
How do careers work?What a person selects as a vocation to generate money is referred to as a career. An individual's career is built on the qualities, abilities, and skills that enable him to pursue personal development and realize his life goals. Correction Services, which entail the construction of detention facilities, are services provided to administrate fines under Dehcho Laws.
A career legal services definitionWhen your profession include providing criminals with rehabilitation programs and facilities that foster progress and motivate them, you're indicating the components of correctional services.
To know more about career pathways visit:-
https://brainly.com/question/13133991
#SPJ1
Question:
If your job involves developing rehabilitation programs for violent criminals, which of the following career pathways might you be following?
Correction Services
Legal Services
Law Enforcement Services
Security and Protective Services
Mahrouq Technologies buys $16,422,433 of materials (net of discounts) on terms of 5/30, net 60, and it currently pays within 30 days and takes discounts. Mahrouq plans to expand, and this will require additional financing. If Mahrouq decides to forego discounts and thus to obtain additional credit from its suppliers, calculate the nominal cost of that credit.
Answers
If Mahrouq were to forego the discounts and obtain additional credit from its suppliers, the nominal cost of that credit would be approximately 36.9% per year.
In order to determine the nominal cost of the credit that Mahrouq Technologies would be foregoing if they decided not to take discounts and obtain additional credit from suppliers, we need to consider the effective annual interest rate (EAR) of the credit.
To calculate the EAR, we need to take into account the terms of the credit that Mahrouq currently receives from its suppliers. The terms are 5/30, net 60, which means that Mahrouq can receive a 5% discount if it pays within 30 days, and the full amount is due within 60 days.
To know more about cost visit:
https://brainly.com/question/14256897
#SPJ11
Which of the following four elements are evaluated for the project purpose?
A: list of relevant data, description of important issues, importance of work, description of problem
B: description of problem, description of solution, list of relevant data, description of important issues
C: importance of work, description of problem, description of solution, list of relevant data
D: description of solution, list of relevant data, description of important issues, importance of work
Answers
Answer:
A
Explanation:
Answer: https://www.careerbuilder.com/advice/what-are-problemsolving-skills-and-why-are-they-important
Explanation:
please if this helps give me brainlest it is about career builder
Raven is adding FSMO roles to domain controllers in the domain1.com forest. The forest contains a single domain and three domain controllers, DC1, DC2, and DC3. DC1 contains a copy of the global catalog, and all three domain controllers have the latest version of Windows Server 2019 installed. Which of the following is a best practice that Raven should follow? She should use DC2 or DC3 as the Domain Naming Master. B She should create the Domain Naming Master role on DC1. She should create three Domain Naming Master roles, one for each domain controller. She does not need to create the Domain Master role because DC1 contains a copy of the global catalog.
Answers
The best practice that Raven should follow is to use DC2 or DC3 as the Domain Naming Master of the following is a best practice that Raven should follow. The correct option is A.
The management of the addition or deletion of domains from the forest is the responsibility of the Domain Naming Master. For redundancy and fault tolerance, it is advised to split the FSMO roles among several domain controllers.
Since DC1 already has a copy of the global catalog, it is advantageous to choose a different domain controller (DC2 or DC3) as the Domain Naming Master to disperse the workload and guarantee high availability. This ensures that the forest's operations may continue even if one domain controller goes offline and prevents the creation of a single point of failure.
Thus, the ideal selection is option A.
Learn more about Domain Naming Master here:
https://brainly.com/question/31558740
#SPJ4
is it necessary to potentially re-engineer parts of the network to support a migration to more wireless or wire-free type of network?
Answers
Yes, it is potentially necessary to re-engineer parts of the network to support a migration to a more wireless or wire-free type of network.
This is because the current network may not have the necessary infrastructure or capacity to support the new type of network. Additionally, there may be compatibility issues between the current network and the new network, which may require re-engineering to resolve. Overall, the process of migrating to a new network may require significant changes to the current network to ensure that it is able to support the new network effectively.
For more information about network, visit:
https://brainly.com/question/1027666
#SPJ11
use the emu8086 to write a program for pushing AX seven times at the stack, check the stack pointer. and [hint : initialize with 8086H] .
Answers
Answer:
I got the point
Explanation:
just chill out baby
An aluminum rod is press fitted onto an aluminum collar. The collar has an inner radius of 1 cm and an outer radius of 2 cm. Given the rod has a diameter of 2.01cm and the young's modulus of aluminum is 69 GPa
Answers
The question is incomplete. The complete question is --
An aluminum rod is press fitted onto an aluminum collar. The collar has an inner radius of 1 cm and an outer radius of 2 cm. Given the rod has a diameter of 1.01 cm and the young's modulus of aluminum is 69 GPa, determine the following :
1. the interference value, i
2. the radial pressure at the interference of the collar and the rod
3. the maximum effective stress in the collar
4. if the yield strength of aluminium is 200 MPa and assume a safety factor of 1.5, will the aluminium collar break
Solution:
Given :
Inner radius of the collar = 1 cm
So, inner diameter, \($d_1$\) = 2 cm
Outer radius of the collar = 12 cm
So, outer diameter, \($d_2$\) = 4 cm
The aluminium rod diameter, d = 1.01 cm
Now, from the figure, we can see that there will be no interference and so the rod will easily insert inside the collar.
1. So, the interference , i =0
2. The radial pressure is also 0.
3. There will be no stress developed. So the maximum effective stress is 0
4. The collar will not break
what could happen if the engine was uncowled during the starting and operating procedures
Answers
If an engine fails during rollout or just before takeoff, immediately shut both throttles and land the aircraft safely. Before reaching a safe single engine speed right away after takeoff, drop your nose to increase velocity.
What is the engine starting procedure?Closing the throttle, turning off the fuel pump, setting the mixture control to idle cutoff, and simply cranking the engine is the most reliable hot start method I've found.
What is the procedure for engine failure?If an engine fails during rollout or just before takeoff, immediately shut both throttles and land the aircraft safely. Before reaching a safe single engine speed right away after takeoff, drop your nose to increase velocity. If you are unable to climb, close both throttles and land straight ahead.
What happens if engine fails during take off?The typical practice for the majority of aircraft would be to abandon takeoff if an engine failed during takeoff. In small aircraft, the pilot should turn the throttles down to idle, activate the speed brakes (if provided), and apply the brakes as needed if the engine fails before VR (Rotation Speed).
To learn more about engine procedure refer to:
https://brainly.com/question/18428188
#SPJ1
WHICH TASK BEST FITS THE ROLE OF A DESIGN ENGINEER ?
Answers
Answer: drafting blueprints
Explanation:
What three modern products would not be available without watt’s contribution to the field?.
Answers
Locomotives, steam ships, and factories with coal-powered machinery these modern products would not be available without watt’s contribution.
How did James Watt's invention affect society?The industrial society of the 18th century was significantly impacted by James Watt's steam engine. Compared to preceding models, it was more economical and efficient.
The watt, a unit of power in the International System of Units (SI) equal to one joule of work performed per second, was called in honour of Watt because of his contributions to science and industry.
Watt's steam engine allowed the steam engine to be utilised to drive rotating equipment in factories like cotton mills, expanding its range of potential uses. It should come as no surprise that Watt's steam engine was in high demand and was swiftly adopted by numerous industries.
His modifications to the steam engine's design transformed it from a water pump for coal mines with few other uses into the source of propulsion that sparked the Industrial Revolution. Rather than being a theorist, Watt is better renowned for his work as an innovator and mechanic.
To learn more about James Watt refer :
https://brainly.com/question/1008453
#SPJ4
Determine the NPW, AW, FW and IRR of the following engineering project. • Initial Cost ($400,000) • The Study Period 15 years Salvage (Market) Value of the project 15% of the initial cost Operating Costs in the first year ($9,000) • Cost Increase 3% per year • Benefits in the first year $40,000 Benefit Increase 9% per year • MARR 8% per year Is the Project acceptable? WHY?
Answers
The CEO of PT ABC asked the project manager to use PW, AW, and FW to prioritize the project while also adding the expected reject rate between each alternative.
Thus, This implies that the anticipated revenue will vary depending on the choice. The three projects are prioritized by the project manager. The CEO will assess which option will be more profitable than the others.
The quantity of money that is accessible for investment, as well as where and how much it cost (for example, whether it came from equity funds or borrowed funds).
The quantity of worthwhile projects that are open to investment and their objective (i.e., whether they maintain current operations and serve a necessary purpose or whether they enlarge current operations and serve a discretionary purpose) and PW.
Thus, The CEO of PT ABC asked the project manager to use PW, AW, and FW to prioritize the project while also adding the expected reject rate between each alternative.
Learn more about Project, refer to the link:
https://brainly.com/question/15999858
#SPJ4