use the phone's ports to daisy chain the pcs to the rest of the network. do not use the regular power outlets to power the phones. the list on the left displays several cable types and devices that may be required in this scenario. drag each cable type or device on the left to the corresponding location identified in the image. items on the left may be used more than once.
Answers
If an image for the matching location on the left is missing, the response will be arbitrary.
I want to daisy chain my phone and computer, but how?Connect a network cable to the phone's PC port before plugging the other end into the computer if you want to daisy-chain a computer to the phone. The connection to the computer should come from the phone (internet source > phone > computer).
Can two IP phones be connected to each other?Yes. Even when one phone doesn't have a regular phone account, you can connect two IP phones to the same network (LAN; it shouldn't be open to the internet since you'll get ghost calls) and call the other one by dialing its local IP address.
To know more about phones visit:-
https://brainly.com/question/19819920
#SPJ1
Related Questions
All of these concerns can be diagnosed using the paper test except for a
a.burned valve.
b.bad spark plug wire in the ignition system.
c.faulty injector on a multi-port engine.
d.cracked exhaust manifold.
Answers
Answer:
cracked exhaust manifold.
Explanation:
When diagnosing some problems in a car engine, a paper test can be utilized to examine and assess for a probable problem that the car is experiencing. Some of the car engine problems a paper test can easily identify are:
1. The ignition system is a bad spark plug wire in a car.
2. A faulty injector on a multiport engine
3. A burned valve
Hence, in this case, the correct answer is "cracked exhaust manifold." This is because to check for a cracked exhaust manifold in a car engine, one is expected to look out for unusual noises like a whistling sound. This type of symptom does not require a paper test.
an engineering firm is evaluating a sophisticated $80,000 laser system to measure the difference in water level between two large tanks. it is important that small differences be measured accurately. you suggest that the job can be done with a $200 manometer arrangement. an oil that is less dense than water can be used to give a 10:1 amplification of meniscus movement: a small difference in level between the tanks will cause 10 times as much deflection in the oil levels in the manometer. determine the specific gravity of the oil required for 10:1 amplification.
Answers
The specific gravity of the oil required for 10:1 amplification is 0.9.
Determine the specific gravity of the oilThe theory used in this question is the specific gravity of a substance, which is the ratio of the density of a substance to the density of water.
Explanations given below
Step 1: Calculate the specific gravity of the oil by dividing the density of the oil by the density of water.
Step 2: Multiply the specific gravity by 10 to get the amplification factor.
Step 3: Divide the desired amplification factor (10) by the calculated specific gravity to get the required specific gravity of the oil.
Example:
Desired amplification factor = 10
Calculated specific gravity = 0.9
Required specific gravity of the oil = 10 / 0.9 = 0.9
To learn more about specific gravity refer :
brainly.com/question/30498001
#SPJ4
Assignment: 1. Create a Raptor program that accepts two numbers from the user and display one of the following messages: First is larger, Second is larger, or the Numbers are equal. Use nested if statements to determine the output. Save your file using the naming format LASTNAME_FIRSTNAME_M04-12. Create a second Raptor program that accepts three numbers from the user and displays a message if the sum of any two numbers equals the third. Save your file using the naming format of LASTNAME_FIRSTNAME M04-2 Documentation is very important for this course and in the field. For all Raptor and all programs, an expectation is that comments will be incorporated into all assignments. For this assignment only the header comments will be required. Both header comments and step comments are encouraged as it will help for logic to be better. Header comments should include the following: Name of the Raptor program Author of the Raptor program Version of the Raptor program and the date of its last revision Summary/goal of the Raptor programVariables used with a short description of the variable, as well as the format of the data (e.g. datatype) . .
Answers
In both programs, it is important to incorporate comments to explain the logic behind the code and make it easier to understand. This is especially important in the field, where other developers may need to work on or modify the code.
The first Raptor program, the goal is to accept two numbers from the user and determine which number is larger or if they are equal.
To achieve this, we can use nested if statements. The Raptor program should start with a header comment that includes the name of the program, author, version, and date of last revision. Additionally, we should include a summary/goal of the program and variables used, along with their data type.In the Raptor program, we can first prompt the user to enter two numbers using the input command. We can then use nested if statements to determine which number is larger or if they are equal. For example, if the first number is greater than the second number, we can display the message "First is larger". Similarly, if the second number is greater than the first, we can display "Second is larger". If both numbers are equal, we can display "The numbers are equal".For the second Raptor program, the goal is to accept three numbers from the user and check if the sum of any two numbers equals the third number. Again, we should start with a header comment that includes the name of the program, author, version, and date of last revision, along with a summary/goal and variables used.
In the Raptor program, we can prompt the user to enter three numbers using the input command. We can then use an if statement to check if the sum of the first two numbers is equal to the third number. If it is, we can display a message saying that the sum of the first two numbers is equal to the third number. If not, we can move on to check if the sum of the second and third numbers is equal to the first number or if the sum of the first and third numbers is equal to the second number. If any of these conditions are met, we can display the appropriate message.
for such more questions on Raptor program
https://brainly.com/question/25324400
#SPJ11
If a digital multimeter displays 000 when reading amperage, what should the technician do to get a more accurate reading
Answers
Answer:
Use a non digital multimeter.
Explanation:
If a digital multimeter displays "000" when reading amperage, the technician should adjust the multimeter to a higher amperage range.
Why should the technician do this?This is because "000" typically indicates that the current being measured is too low for the current range selected on the multimeter.
By switching to a higher amperage range, the technician can get a more accurate reading and ensure that the multimeter is properly measuring the current in the circuit under test.
Learn more about digital multimeter at:
https://brainly.com/question/29512413
#SPJ3
What signal propagation phenomena causes the diffusion, or the reflection in multiple different directions, of a signal?
Answers
In the radio communication system, multipath is the propagation phenomenon that causes diffusion or reflection in multiple different directions of a signal.
Multipath is a propagation mechanism that impacts the propagation of signals in radio communication. Multipath results in the transmission of data to the receiving antenna by two or more paths. Diffusion and reflection are the causes that create multiple paths for the signal to be delivered.
Diffraction occurs when a signal bends around sharp corners; while reflection occurs when a signal impinges on a smooth object. When a signal is received through more than one path because of the diffraction or reflection, it creates phase shifting and interference of the signal.
You can learn more about signal propagation at
https://brainly.com/question/14452898
#SPJ4
The phase angle in a circuit is 45 degrees what's the power factor of this circuit?
Answers
The power factor of the circuit is 0.7071
What is Power factor?Power factor (PF) is the ratio of working power, measured in kilowatts (kW), to apparent power, measured in kilovolt amperes (kVA). Apparent power, also known as demand, is the measure of the amount of power used to run machinery and equipment during a certain period. It is found by multiplying (kVA = V x A). The result is expressed as kVA units.
Power factor is expressed as the cosine of the phase angle.
The phase angle is given as 45°
Therefore the power factor in the circuit is cos45° = 0.7071
learn more about power factor from
https://brainly.com/question/25543272
#SPJ1
An equipment or process
powered by compressed air is
Answers
Answer:
An equipment or process powered by compressed air is a pneumatic tool.
People commonly use contact lenses to correct their vision. A patient has a near point of 120 cmand, to correct this, wears contact lenses with a focal length of 30 cm .
A. What is the refractive power of her contact lenses?
1.1 diopters
0.83 diopters
3.3 diopters
0.033 diopters
Answers
The refractive power of the contact lenses can be calculated using the following formula: refractive power (in diopters) = 1 / focal length (in meters).
Converting the given focal length of 30 cm to meters, we get 0.3 m. Substituting this value in the formula, we get: Refractive Power = 1 / 0.3 = 3.3 diopters. Therefore, the refractive power of her contact lenses is 3.3 diopters.
To determine the refractive power of the contact lenses, we need to use the formula:
Refractive Power (D) = 1 / Focal Length (m)
First, let's convert the focal length from centimeters to meters:
Focal Length = 30 cm = 0.3 m
Now, we can plug the value into the formula:
Refractive Power (D) = 1 / 0.3 m = 3.33 diopters
The closest answer choice to 3.33 diopters is 3.3 diopters. Therefore, the refractive power of her contact lenses is 3.3 diopters.
to know more about refractive power:
https://brainly.com/question/25164545
#SPJ11
calculate force and moment reactions at bolted base O of overhead traffic signal assembly. each traffic signal has a mass 36kg, while the masses of member OC and AC are 50Kg and 55kg, respectively. The mass center of mmber AC at G.
Answers
Answer:
The free body diagram of the system is, 558 368 368 508 O ?? O, Consider the equilibrium of horizontal forces. F
Explanation:
I hope this helps you but I think and hope this is the right answer sorry if it’s wrong.
The big ben clock tower in london has clocks on all four sides. If each clock has a minute hand that is 11.5 feed in length, how far does the tip of each hand travel in 52 minutes?
Answers
Answer:
Updated question
The big ben clock tower in London has clocks on all four sides. If each clock has a minute hand that is 11.5 feet in length, how far does the tip of each hand travel in 52 minutes?
The distance traveled by the tip of the minute hand of the clock would be 62.59 ft
Explanation:
Let us assume the shape of the clock is circular.
the minute hand is equal to the radius = 11.5 ft
Diameter = radius x 2
Diameter = 11.5 x 2 = 23 ft
The distance traveled by the tip of the minute hand can be calculated thus;
the fraction of the circumference traveled by the minute hand would be;
52/60 = 0.8667
Circumference of the clock would be;
C = pi x d
where C is the circumference
pi is a constant
d is the diameter
C = 3.14 x 23
C = 72.22 ft
Therefore the fraction of the circumference covered by the minute hand would be;
72.22 ft x 0.8667 = 62.59 ft
Therefore the distance traveled by the tip of the minute hand of the clock would be 62.59 ft
Where you attend college could costmore to borrow and refinance loans
Answers
Which of the following would be useful to the building of a skyscraper? (Select all that apply.)
steep grading
deep foundation
wide footing
large footprint
Answers
Answer:
steep grading
Explanation:
the farthest
I will rate 5 stars/brainliest if you help me!!! A company produces A, B, and C and can sell these products in unlimited quantities at the following unit prices: A, $10; B, $56; C, $100. Producing a unit of A requires 1 hour of labor; a unit of B, 2 hours of labor plus 2 units of A; and a unit of C, 3 hours of labor plus 1 unit of B. Any A that is used to produce B cannot be sold. Similarly, any B that is used to produce C cannot be sold. A total of 40 hours of labor are available. Formulate an LP to maximize the company’s revenues. (Please solve the LP with Lindo or Excel).
Answers
Answer: 0
Explanation: i need to add it up to get what u want
technician a says that loose ball joints can cause the vehicle to wander. technician b says that loose control arm bushings can affect alignment angles. who is correct?
Answers
Technician a is correct. The car may veer off course due to loose ball joints. The propensity of a vehicle to veer from one side of the road to the other is known as wander.
The propensity of a vehicle to veer from one side of the road to the other is known as wander. Uneven tire pressure or mismatched tires are potential causes number one. Linkage binding or inadequate lubrication is a potential cause number two. The third potential factor is binding or inadequate lubrication of the steering gear.
The bottom line is that before you start to address poor steering performance, you must identify the underlying source of the issue. Oversteer and understeer have been discussed separately, but we've also included 10 other common steering issues with their likely causes below. You can stop cursing and start fixing your steering problems by locating potential problem areas.
To know more about potential click here:
https://brainly.com/question/4305583
#SPJ4
a transformer used to operate a neon sign steps 120vac up to 6000 v. the primary has 150 turns. how many turns does the secondary have?
Answers
To find the number of turns in the secondary of the transformer, we can use the turns ratio equation:
Turns ratio = (Number of turns in secondary) / (Number of turns in primary)We know that the transformer steps up the voltage from 120 V to 6000 V, which means the turns ratio is:Turns ratio = (Voltage in secondary) / (Voltage in primary) = 6000 V / 120 V = 5Therefore, we can calculate the number of turns in the secondary as:Number of turns in secondary = Turns ratio x Number of turns in primarNumber of turns in secondary = 50 x 15Number of turns in secondary = 7500Therefore, the secondary of the transformer has 7500 turns.
To learn more about secondary click on the link below:
brainly.com/question/25886292
#SPJ11
d
K
A shaft consisting of a steel tube of 50-mm outer diameter is to transmit 100 kW of power while rotating at a frequency of 36 Hz.
Determine the tube thickness that should be used if the shearing stress is not to exceed 60 MPa.
The tube thickness that should be used is [
mm.
Answers
Based on the information, the tube thickness that should be used is 3.18 mm.
How to calculate the valuePower = Torque * Angular velocity
100 kW = Torque * (2 * pi * 36 Hz)
Torque = 2212.14 N-m
In this case, the polar moment of inertia is:
J = pi * 50⁴ / 32 = 196250 pi mm⁴
Maximum shear stress = Torque / J
Maximum shear stress = 2212.14 N-m / 196250 pi mm⁴ = 0.0499 MPa
Tube thickness = 2 * ✓(60 MPa / pi * 50²) = 3.18 mm
Therefore, the tube thickness that should be used is 3.18 mm.
Learn more about tube on
https://brainly.com/question/14680662
#SPJ1
A scale on a blue print drawing of a house shows that 666 centimeters represents 333 meters.
What number of centimeters on the blue print represents an actual distance of 272727 meters?
Answers
Answer:
545454cm
Explanation:
The blue print drawing of the house shows 666 centimeters, but the real picture of the house is 333 meters. So let the number of cm on the blueprint that represent the distance of 272727 meters be x. Firstly convert the meters to centimeters 666cm = 333m, x=272727m ; then cross multiply, 666cm=33300cm x=27272700cm ; x =(666cm×272727cm)/33300cm =545454cm.
Hey guys can anyone list chemical engineering advancement that has been discovered within the past 20 years
Answers
Nanopesticides. The world population keeps growing. ...
Enantio selective organocatalysis. ...
Solid-state batteries. ...
Flow Chemistry. ...
Porous material for Water Harvesting. ...
Directed evolution of selective enzymes. ...
From plastics to monomers. ...
Match the example to the model type it represents.
1. The client complains about the way the keyboard feels
1.mock-up
2. The engineering team tests how the tire treads on a new SUV perform on 2.various road conditions
preproduction model
3. The engineering team performs tests on the efficiency of the manufacturing process used for a recumbent bicycle
3.presentation model
Answers
Answer:
represnt
Explanation:
technician A says that a power balance test is a good way to narrow a misfire down to a particular cylinder(s). technician B says that a cylinder power balance test measures the volumetric efficiency of the cylinder being tested
Answers
Answer: Technician B.
Explanation: Please vote brainliest.
A mixed economy combines the traits of which two economic systems?
A. Marxist and traditional
B. Market and command
C. Traditional and market
D. Command and traditional
Answers
A mixed economy combines the traits of these two (2) economic systems: B. market and command.
What is a mixed economy?A mixed economy can be defined as a type of economic system in which the government of a particular country is minimally involved in the allocation and production of goods and services, while effectively protecting the interest of the consumers and regulating the market by establishing laws.
This ultimately implies that, a mixed economy combines the traits of these two (2) economic systems market and command.
Read more on mixed economy here: https://brainly.com/question/13467040
#SPJ1
Write the different professions and human resources related to engineering and expalin any two of them?
Answers
Answer:
some of the professions and human resource related to engineering are:
Aerospace engineerAgricultural engineer Electrical engineer computer engineerproject Manger construction site engineer/supervisorAerospace engineering involves the study, design and development of spacecrafts using Core science principles.
Electrical engineering involves the study and application of core science principles especially physics and mathematics into providing Electrical related solutions
Explanation:
Engineering is a major branch of applied science. In general Engineering is concerned with the design and building of engines ( i.e. application of scientific/science facts )
some of the professions and human resource related to engineering are:
Aerospace engineerAgricultural engineer Electrical engineer computer engineerproject Manger construction site engineer/supervisorAerospace engineering involves the study, design and development of spacecrafts using Core science principles.
Electrical engineering involves the study and application of core science principles especially physics and mathematics into providing Electrical related solutions
Will a thermal boundary layer develop in flow over a surface even if both the fluid and the surface are at the same temperature?
Answers
Answer:
i hope it's correct
Explanation:
A thermal boundary layer will not develop in flow over a surface if both the fluid and the surface are at the same temperature since there will be no heat transfer in that case.
what is the ratio of the induced emf in the loop cdbc to the induced emf in the loop cadc; i.e., what is ecdbc ecadc ?
Answers
The ratio of the induced EMF in the loop CDBC to the induced EMF in the loop CADC can be calculated as follows:
ecdbc/ecadc = -dΦ_cdbc/dt / (-dΦ_cadc/dt) = dΦ_cadc/dt / dΦ_cdbc/dt
Let's dive deeper into the details below
The induced EMF is the voltage generated by a changing magnetic field in a coil of wire. In a loop, the induced EMF is proportional to the rate of change of the magnetic flux that is threading the loop. Therefore, in a loop, the induced EMF can be calculated as:
induced EMF = -dΦ/dt, where Φ is the magnetic flux threading the loop.
We can assume that both loops are parallel to the surface and therefore perpendicular to the magnetic field. This means that the magnetic flux threading each loop is proportional to the area of the loop, as follows:
Φ_cadc = B A_cadc and Φ_cdbc = B A_cdbc
Therefore, the ratio of the induced EMF in the loop CDBC to the induced EMF in the loop CADC can be calculated as follows:
ecdbc/ecadc = dΦ_cadc/dt / dΦ_cdbc/dt = (B A_cadc)/dt / (B A_cdbc)/dt = A_cadc / A_cdbc
The answer is the ratio of the areas of the loops.
Learn more about magnetic flux.
brainly.com/question/30858765
#SPJ11
Which of the following statements is true about a critical path?
A. It consists of activities for which early start time equals late start time.
B. The total time of activities on the path take the longest time.
C. There is no slack in the activities along the critical path.
D. All of the above.
Answers
The statement that would be true about a critical path is; "All the Above" (Option D)
What is a Critical Path and why is it important?A critical path is the sequence of activities in a project that must be completed on time in order for the project to be completed on schedule. It is the longest path through the project, from start to finish, and includes the activities that have the least amount of scheduling flexibility. These activities are considered "critical" because any delay in their completion will directly impact the overall completion date of the project.
The critical path is important because it helps project managers identify the most important tasks in the project and allocate resources accordingly.
Learn more about Critical path:
https://brainly.com/question/16519233
#SPJ1
how does a TV'S screen work
Answers
Answer:
A TVS screen works when the pixels are switched on electronically using liquid crystals to rotate polarized light.
Explanation:
technician a states that a trigger helps stabilize a waveform. technician b states that if a trigger is misplaced, the waveform can be unstable or not seen. who is correct? technician a technician b both technicians neither technician
Answers
Technician B only
What is External Trigger Source?An input voltage is applied to the external input jack. This is the BNC input labeled EXT TRIG IN at the bottom right corner of the horizontal trigger section of the LS1020 oscilloscope shown in Figure 3.35. The voltage applied to this input is used to trigger the sweepTriggers are the method by which an oscilloscope synchronises the voltage and time data of your waveform, enabling you to view your signal fixed to a voltage/time point to analyse it furtherIn auto trigger mode, the trigger will be forced if the specified conditions are not met. In normal trigger mode, the trigger will never be forced and a trigger will only occur if the specified conditions are met.
To learn more about External Trigger refers to:
brainly.com/question/29698882
#SPJ4
oversized duct systems cost more to fabricate and install and will also result in the slowing of the air as it flows through the duct.
Answers
Therefore, oversized duct systems can be costly to fabricate and install, and they can also negatively impact airflow efficiency. Proper sizing of duct systems is essential to avoid these drawbacks and ensure optimal performance.
Oversized duct systems have several disadvantages, both in terms of cost and airflow efficiency. Let's break it down step-by-step:
1. Cost: Fabricating and installing oversized duct systems require more materials, which can significantly increase the overall cost of the project. Additionally, larger ducts may require additional labor and time to install, further contributing to the increased cost.
2. Airflow Efficiency: When air flows through an oversized duct system, it tends to slow down. This can result in reduced airflow efficiency, as the air has more space to move around and loses velocity. As a result, the system may struggle to distribute air evenly throughout the space it is intended to serve. This can lead to uneven temperatures and discomfort for the occupants.
It is important to note that oversized duct systems can also lead to increased energy consumption and decreased system performance. When the air slows down, it may not reach its intended destination within the required timeframe, resulting in longer running times for the HVAC system. This extended operation can lead to higher energy bills and increased wear and tear on the system components.
To avoid these issues, it is crucial to properly size duct systems according to the specific requirements of the space. This involves considering factors such as the size of the room, the number of occupants, and the desired airflow rate. By correctly sizing the ductwork, you can ensure optimal performance, energy efficiency, and comfort.
Oversized duct systems can be costly to fabricate and install, and they can also negatively impact airflow efficiency. Proper sizing of duct systems is essential to avoid these drawbacks and ensure optimal performance.
To learn more about energy consumption visit:
brainly.com/question/30337392
#SPJ11
1)A wheel is used to turn a valve stem on a water valve. If the wheel radius is 1 foot and the stem, (axle), radius is .5 inches, what is the mechanical advantage of the wheel and axle? 2)How much resistance force can ideally be overcome when an effort of 80 lbs is applied to the wheel of the water valve in problem 1? 3)What is the linear distance traveled when a 2.5' diameter wheel makes one revolution? 4)A compressor motor has a 1.00 inch output shaft (axle) that drives a 4.00inch pulley (wheel). If the motor output shaft supplies 24 lbs of force, ideally how much force does the pulley apply to the drive belt wrapped around it? 5) If the belt pulley's force is measured to be 4 lbs, what is the AMA wheel and axle here?6) What is the efficiency of the compressor motor – belt pulley wheel and axle?
Answers
Answer:
for 13
Explanation:
''.''
unitate de masura in SI pt F
Answers
Answer:
Electrical Capacitance
Explanation:
To find - unit of measure in SI for F
Solution -
The answer is - Electrical Capacitance
Reason -
The farad (symbol: F) is the SI derived unit of electrical capacitance, the ability of a body to store an electrical charge.
Răspuns:
Capacitate electrică
Explicaţie:
Pentru a găsi - unitate de măsură în SI pentru F
Soluție -
Răspunsul este - Capacitate electrică
Motiv -
Farada (simbolul: F) este unitatea de capacitate electrică derivată din SI, capacitatea unui corp de a stoca o sarcină electrică.