Technician A says that an electronic suspension can use a driver input such as soft, normal, hard. Technician B says that most electronically controlled suspension systems use a separate electronic control module. Which technician is correct
Answers
Technician A is correct. An electronic suspension system can indeed utilize driver inputs such as soft, normal, and hard modes.
These modes allow the driver to adjust the characteristics of the suspension system to suit their preferences or the driving conditions.
Electronic suspensions employ various sensors and actuators to continuously monitor and control the suspension behavior in real-time.
The driver inputs, such as soft, normal, or hard modes, are typically selected through a control interface, such as a button or a switch in the cabin.
These inputs send signals to the electronic control module (ECM) responsible for managing the suspension system.
Technician B's statement is also accurate. Most electronically controlled suspension systems do use a separate ECM to process the input signals and adjust the suspension parameters accordingly.
The ECM receives input from various sensors, such as accelerometers, height sensors, and wheel speed sensors, to monitor the vehicle's dynamics and road conditions.
Based on the driver's input and the sensor data, the ECM controls the actuators within the suspension system to modulate factors like damping rates, ride height, and stiffness.
This enables the suspension system to adapt to different road conditions and driving scenarios, providing improved comfort, handling, and stability.
For more questions on electronic suspension system
https://brainly.com/question/31237603
#SPJ11
Related Questions
Allura Red Moles
Question of the Day {QOD}:
If you decided to drink massive amounts of Cherry Kool-AidTM on a dare, would you die from Allura Red toxicity or water intoxication first?
5. Answer the Question of the Day. Support your answer with specific evidence from your experimentation including LD50 calculations. In your discussion, calculate both the amount of grams and moles of Allura red in Kool-Aid as well as the volume of Kool-Aid you would need to ingest to reach the median lethal dose of Allura red
The concentration of Allura red used was 1.89x10^-4 M
Kool aid absorbance (after dilution: 1mL kool aid, 9mL water): 0.453
Kool aid concentration: 1.97x10^-4 M
LD50 water: 90g/kg
LD50 (rats and mice): 6,000 - 10,000 mg/kg
Answers
Answer:
Die of intoxication by water first
Explanation:
We assume that the weight of the man is 154.35 pounds which is 70 kg
LD50 water = 90g per kg
Maximum concentration = 90x70
= 6300grams
Convert grams to liters
6300/100
= 6.3 litres
From here we get amount of kool aid
6.3 x 1.97x10^-4
= 1.24x10^-3
= 1.24grams
1.24 grams is below 420 kool aid is lower than LD50 with about 6 grams for 1 kg (6x70kg = 420). So 420 is lethal dose. But 1.24 is less than this so the man has to die of water intoxication first.
Passive optical networks (PONs) require the use of active OEO (optical-electrical-optical) repeaters between the subscriber and service provider.
True
False
Answers
The statement is false.
Passive optical networks (PONs) do not require the use of active OEO repeaters between the subscriber and service provider. PONs are designed to be passive, which means that the signal is transmitted from the central office to the subscriber without any active components in between. Instead, the signal is split and distributed to multiple subscribers using passive optical splitters. This makes PONs more cost-effective and energy-efficient than other types of optical networks. However, some PONs may use active components in the network, such as amplifiers or wavelength converters, but they are not required between the subscriber and service provider.
To know more about Passive optical network visit:
https://brainly.com/question/28076810
#SPJ11
In doing a load of clothes, a clothes drier uses \( 15 \mathrm{~A} \) of current at \( 240 \mathrm{~V} \) for \( 52 \mathrm{~min} \). A personal computer, in contrast, uses \( 2.0 \mathrm{~A} \) of cu
Answers
The time taken by the personal computer to use the same amount of energy consumed by the clothes drier is 26 minutes (approx.).
The time taken by the personal computer to use the same amount of energy consumed by the clothes drier is determined using the given information.
The details that are given in the problem are:
Current taken by clothes drier: I = 15 A
Current taken by personal computer: I = 2 A
Time taken by clothes drier:
t₁ = 52 min
= 52/60 hours
Power consumed by clothes drier:
P₁ = V₁*I₁ = 240*15 W
Let's find out the amount of energy consumed by the clothes drier.
The energy consumed by the clothes drier can be calculated as:
W1 = P₁*t₁
= 240*15*(52/60)Wh
W₁ = 26,400 Wh
The power consumed by the personal computer is:
P2 = V₂*I₂
= 120*2 W
The energy consumed by the personal computer is:
W₂ = P₂*t₂Wh
Let's find out the time taken by the personal computer to use the same amount of energy consumed by the clothes drier.
To find the time t₂, we will equate the energy consumed by the personal computer to that of the clothes drier.
Thus,
W₁ = W₂
P₁*t₁ = P₂*t₂
t₂ = (P₁*t₁)/P₂
Substituting the values, we get:
t₂ = (240*15*(52/60))/(120*2)
t₂ = 26 min (approx.)
Hence, the time taken by the personal computer to use the same amount of energy consumed by the clothes drier is 26 minutes.
To know more about energy, visit:
https://brainly.com/question/8630757
#SPJ11
What types of information are provided in the invitation to bid?
Answers
Answer:
A comprehensive Invitation for Bid (IFB) solicitation will describe the planned project in detail, lay out submission requirements including deadlines, project scope and duration, minimum qualifications, mandatory service standards, and required warranties.
Find the ratio of the volume generated when the curve 25x^{2} - 16y^{2} + 700xy = 400 makes a half revolution about its directrix and when it makes a full revolution about the line connecting its foci.
Answers
To find the ratio of the volume generated by the curve 25x² - 16y² + 700xy = 400, we can start with the formula for calculating the volume of revolution about the axis of symmetry:
V = π * ∫[a, b] [(f(x))² dx]
Case 1: Half revolution about the directrix 700xy = 400 - 25x² + 16y² ---(1)
The directrix of the parabola is given by y = -(b²/a), where a is the distance from the vertex to the focus and b is the distance from the vertex to the directrix.
Here, a² = (400/25) = 16 and b = 7, which gives the directrix as y = -49/16.
The axis of symmetry is given by x = 0. Using the standard formula, the curve is given by y = (1/700) (400 - 25x²)/(16/7).
We need to calculate the integral ∫[-a, a] [(y)² dx], which is equal to 2∫[0, a] [(y)² dx].
On substituting the value of y, we get:
V = π * (2/700²) ∫[0, a] [(400 - 25x²)/(16/7)]² dx = π * 0.0681
Case 2: Full revolution about the line connecting its foci
700xy = 400 - 25x² + 16y² ---(2)
We can rewrite equation (2) as y² = (4/25)x² - (7/25)x + 1.
The vertices of this hyperbola are (5/2, 0) and (-5/2, 0).
The foci of the hyperbola can be found using the formula c² = a² + b², where c is the distance from the center of the hyperbola to the foci and a and b are the semi-axes of the hyperbola. Here, a = 5/2 and b = √(1 + (7/25)²) = 24/5. This gives c = √((25/4) + (24/5)²) = 17/4.
The line connecting the foci is given by x = (c/b)y.
Let P be a point (x, y) on the hyperbola. The distance from the point to the line connecting the foci is given by (2a²/c) * sqrt((c/b)y - x + (a/c)²).
Using the distance formula, we get 25x² - 16y² = (1/196) [(34y/5) - x]².
We need to calculate the integral ∫[-a, a] [(y)² dx], which is equal to 2∫[0, a] [(y)² dx].
On substituting the value of y, we get:
V = π * (2/1225²) ∫[0, 5] [(34y/5 - 25y²/4)]² dy = π * 3.35 x 10⁻⁴
Hence, the ratio of the volumes is given by V₂/V₁ = 0.0681/3.35 x 10⁻⁴.
To know more about revolution visit:
https://brainly.com/question/29158976
#SPJ11
list the components of a typical Foundation drainage system and their functions.
Answers
Explanation:
In this series, the professionals at the B.O.L.D. Company will take you through the process of building a custom home in the Greater Cincinnati – Northern Kentucky area. From plan and lot selection, to mortgage approval, to the actual construction, we’ll take you behind-the-scenes each week for an inside look at a different part of the process.
A weather satellite has an expected life of 10 years from the time it is placed into earth orbit. Determine its probability of no wear-out before each of the following lengths of service. Assume the exponential distribution is appropriate. A) 5 years. B) 12 years. C) 20 years.
Answers
The probability of no wear-out before 20 years is: $1 - P(X > 20) = 1 - e^{-2} \approx 0.8647$, As weather satellite has an expected life of 10 years from the time it is placed into earth orbit.
The probability of no wear-out before each of the following lengths of service: A) 5 years, B) 12 years, and C) 20 years for a weather satellite that has an expected life of 10 years from the time it is placed on Earth orbit, can be determined using the exponential distribution.
Formula for the exponential distribution: $P(X > x) = e^$
Where $P(X > x)$ is the probability that the equipment lasts longer than x years; $\mu$ is the mean lifetime of the equipment.
Given, $\mu$ = 10 years.
A) For the service life of 5 years, we have: $P(X > 5) = e^{- \frac{5}{10}} = e^{-0.5} \approx 0.6065$
Therefore, the probability of no wear-out before 5 years is: $1 - P(X > 5) = 1 - e^{-0.5} \approx 0.3935$
B) For the service life of 12 years, we have: $P(X > 12) = e^{- \frac{12}{10}} = e^{-1.2} \approx 0.3012$
Therefore, the probability of no wear-out before 12 years is: $1 - P(X > 12) = 1 - e^{-1.2} \approx 0.6988$
C) For the service life of 20 years, we have: $P(X > 20) = e^{- \frac{20}{10}} = e^{-2} \approx 0.1353$
Therefore, the probability of no wear-out before 20 years is: $1 - P(X > 20) = 1 - e^{-2} \approx 0.8647$
To know more about weather satellite please refer:
https://brainly.com/question/7115770
#SPJ11
21. Protecting the whole ecosystem may help save many help save many species,but it will not help to maintain the ecosystem functions
False
True
Answers
Answer:
TRUE
Explanation: I think
protecting the ecosystem saves the species is true because a lot of species lives in the ecosystem and is there habitat / i think
push buttons combine the operation of a selector switch and push button in the same unit is called ?
Answers
The device you are referring to is typically called a "push button selector switch" or a "selector switch with push button".
This type of switch combines the functions of both a selector switch and a push button into a single unit. It allows the user to select a particular position or function by rotating the switch to the desired position, and then activate that function by pressing the button associated with that position.
Push button selector switches are commonly used in control panels and other industrial applications where it is necessary to select and activate different functions or operations with a single device.
Learn more about Pushbuttons:
https://brainly.com/question/30242424
#SPJ4
What accident theory divides an accident into three phases: pre-contact, contact, and post-contact?
Answers
The accident theory divides an accident into three phases: pre-contact, contact, and post-contact is the domino theory.
What is the domino theory?The domino theory is a geopolitical theory that holds that changes in democracy in one country have a domino impact on surrounding countries.
The multiple-factor theory examines not just the three domino theory phases—precontact, contact, and post-contact—but also additional elements that influence an accident, such as management, machine, media, and man.
Therefore, the domino theory separates an accident into three phases: pre-contact, contact, and post-contact.
To learn more about the domino theory, refer to the link:
https://brainly.com/question/28082356
#SPJ1
Assignment 1."Value chain analysis is not a very difficult exercise conceptually"Clarify 2.Supply Chain Management drives supply chain members to have a customer orientation, Explain 3.A typical supply chain may involve a variety of
Answers
A typical supply chain may involve a variety of stages such as:
(i) Customers.
(ii) Retailers.
(iii) Wholesalers/Distributors.
What is a supply chain?A supply chain is a group of people and businesses involved in producing and distributing goods to customers.
The supply chain is the network of all the people, businesses, resources, tasks, and technological advancements involved in the production and distribution of a good. An entire supply chain, from the delivery of raw materials from the supplier to the manufacturer to the final delivery to the customer, is included.
Therefore, the typical supply chain may involve a variety of stages such as Customers, Retailers and Wholesalers.
Learn more about supply chain on:
https://brainly.com/question/25160870
#SPJ
A cylindrical 1045 steel bar is subjected to repeated compression-tension stress cycling along its axis. If the load amplitude is 22,000 N (4950 lbf), compute the minimum allowable bar diameter to ensure that fatigue failure will not occur. Assume a factor of safety of 2.0
Answers
Answer:
13.4 mm
Explanation:
Given data :
Load amplitude ( F ) = 22,000 N
factor of safety ( N )= 2.0
Take ( Fatigue limit stress amplitude for this alloy ) б = 310 MPa
calculate the minimum allowable bar diameter to ensure that fatigue failure will not occur
minimum allowable bar diameter = 13.4 * 10^-3 m ≈ 13.4 mm
attached below is a detailed solution
Determine the horsepower required to compress 1 lbm/min of ethylene oxide from 70 oF and 1 atm to 250 psia. The compressor has an efficiency of 75%. The molar heat capacity of ethylene oxide is given by Cp
Answers
Complete Question:
Problem 8 Determine the horsepower required to compress 1 lbm/min of ethylene oxide from 70 °F and 1 atm to 250 psia. The compressor has an efficiency of 75%. The molar heat capacity of ethylene oxide is given by
C_p=10.03+0.0184T C_p[=]Btu/lbmole- "F ; T[=] °F C,
Answer:
\(P'=0.377hp\)
Explanation:
From the question we are told that:
Initial Temperature T_1=70 F
Final Temperature \(T_2=250pisa =114.94F\)
Efficiency \(E=75\%=0.75\)
Generally the equation for Work-done is mathematically given by
\(W=\int C_pT\)
\(W=10.03(114.94-70 )+0.0184((114.94)^2-70^2 )\)
\(W=527.21btu/ibmole\)
\(W=11.982btu/ibm\)
Generally the equation for Efficiency is mathematically given by
\(E=\frac{isotropic Power}{Actual P'}\)
\(E=\frac{P}{P'}\)
Since
Isotropic Power
\(P=0.0167*11.982btu/ibm\)
\(P=0.2btu/s\)
Therefore
\(P'=\frac{0.2}{0.75}\)
\(P'=0266btu/s\)
Since
\(1btu/s=1.4148hp\)
Therefore
\(P'=0.377hp\)
What are the important subassemblies and subsystems?
Answers
Answer:
Subsystem denotes to the installation of some subassemblies, which can be very small or gigantic in size, that serve this subsystem and the overall system. ... In addition, availability importance measures are employed to rank various subsystems with regards to their impact on the overall system availability.
Explanation:
Subsystem refers to the installation of a few subassemblies that support this subsystem and the entire system.
What are subassemblies?An assembly is a template for a corridor's cross section at a certain station.
A set of interconnected subassemblies that are each connected to a center point or to other subassemblies makes up an assembly. An assortment of shapes, linkages, and points make up a subassembly.
The installation of a few subassemblies that support this subsystem and the overall system is referred to as a subsystem.
These subassemblies can range in size from little to huge. In addition, subsystems are ranked according to their impact on the overall system's availability using availability importance criteria.
The primary memory, the input/output subsystem, and the central processor unit (CPU) are the three basic categories or subsystems that make up a computer. Data processes are carried out by the central processing unit (CPU).
A subassembly could be:
Semiconductor.Amplifier.Transistor.Impedance.Oscillators.Thus, these are important subassemblies and subsystems.
For more details regarding subassemblies, visit:
https://brainly.com/question/14940424
#SPJ2
3 To improve the acoustics in auditorium, a sound reflector with mass
of 200 kg is suspended by a chain from the ceiling. What is its
weight? What force (magnitude and direction) does the chain exert
on it? What is the tension in the chain? Assume that the mass of the
chain itself is negligible.
Answers
To improve the acoustics in auditorium, a sound reflector with mass of 200 kg is suspended by a chain from the ceiling thus thet force (magnitude and direction) does the chain exert on it =1960 N.
What is Newton's third regulation?
Ths 0.33 regulation states that for each movement (pressure) in nature there's an identical and contrary response. If item A exerts a pressure on item B, item B additionally exerts an identical and contrary pressure on item A. In different words, forces end result from interactions.
Weight of reflector = mg=200^ * 9.8=1960 NForce exerted with the aid of using chain =1960 NDirection = upwardsTension at the chain = weight of reflector=1960 NWeight of reflector =mg =100 * 9.8=980NMagniyof pressure reflector exerts on earth = 980 N(Due to movement response pair of forces, consistent with Newton's 0.33 regulation of motion.Read more about the Newton's law:
https://brainly.com/question/25545050
#SPJ1
traditional hydraulic and pneumatic control systems are being replaced by what types of systems to save in weight?
Answers
There is no proof that hydraulics is always more "efficient" in every circumstance, however it might be in some applications.
What would happen if a pneumatic system took the place of the hydraulic system? There is no proof that hydraulics is always more "efficient" in every circumstance, however it might be in some applications.It is "more efficient" to use hydraulics when:mobile tools for earth moving and construction .Presses for shaping metal,machinery for extrusion, especially plastics.Various lift types, such as elevators and platforms than pneumatic machineryAlternatively, pneumatics:work more quickly than hydraulics.yastmastmastmastmas, and can be utilized for applications requiring significantly higher precision.are significantly safer around processes involving food, drinks, and medicines.are safer in terms of substantially lower flammability and the risks of piping failures that go along with it.To learn more about hydraulic refer
https://brainly.com/question/857286
#SPJ4
A producer is someone who _____________.
A.
Makes a commodity available for sale or exchange
B.
Buys or trades in order to receive a commodity
C.
Is in the market for a commodity
D.
Receives a commodity from a business
Answers
Answer: A. Makes a commodity available for sale or exchange
Explanation: hope it helps ^w^
given the wheelbase of the car 138.8 inches, trackwidth 75 inches and loads on tires as follows. determine the longitudinal cg location in inches measured from the front wheel,
Answers
Wheelbase, trackwidth, and tire load data can be used to determine the longitudinal CG location. The distance in inches between the center of gravity and the front wheel.
Wheelbase, trackwidth, and tire load data can be used to determine a car's longitudinal center of gravity (CG) location. The distance between the centers of the front and rear wheels is known as the wheelbase, while the distance between the left and right tire centerlines is known as the trackwidth. The amount of weight on each of the four tires that are in contact with the ground is known as the tire load. The entire weight of the vehicle is divided by the wheelbase and trackwidth, and the resulting number is multiplied by the wheelbase to determine the longitudinal center of gravity (CG) location. The resultant measurement, taken from the front wheel, is the longitudinal CG location in inches.
Learn more about distance here-
https://brainly.com/question/19915401
#SPJ4
Multiple Choice
The first step in product analysis is to disassemble a product.
True
False
Answers
Answer:
the answer is false
Explanation:
i took the advice of the other person and found a Quizlet that said false :)
i hope this helps :D
The appearance,natural durability of wood and its workability are some of the factors that has made wood greatly used for constructional purposes. Explain
Answers
The appearance, natural durability, and workability of wood are some of the factors that make wood a popular material for construction purposes.
Explanation: Wood is a popular material for construction purposes because of its appearance, natural durability, and workability. These factors are the reasons why wood is still a favorite of many builders and homeowners today.
Appearance: Wood is an aesthetically pleasing material with a natural beauty that is hard to replicate. The unique pattern and texture of wood grains are a beautiful sight to behold. The natural color and texture of wood can add warmth and character to any room. Wood's natural beauty makes it a popular choice for flooring, furniture, and decorative features.
Natural Durability: Wood is a durable material that can withstand the test of time. Wood is naturally resistant to wear and tear, rot, and insect damage. This makes it a popular choice for construction purposes, especially in outdoor applications. With proper maintenance, wood can last for many years without showing any signs of damage.
Workability:Wood is a highly workable material that can be easily shaped and molded to fit any design. Wood can be easily sawed, drilled, and carved to create complex designs and shapes. This makes it a popular choice for furniture makers, carpenters, and other woodworkers who need a material that is easy to work with.
In conclusion, the appearance, natural durability, and workability of wood are the main factors that have made it a popular material for construction purposes. Wood's natural beauty, durability, and workability make it a versatile material that can be used in many different applications.
Know more about Wood here:
https://brainly.com/question/10967023
#SPJ11
43) According to kinetic-molecular theory, if the temperature of a gas is raised from 100°C to 200°C, the average kinetic energy of the gas will
A) double
B) increase by a factor of 1.27
C) increase by a factor of 100
D) decrease by half
E) decrease by a factor of 100
Answers
A) double
According to the kinetic-molecular theory, the temperature of a gas is a measure of the average kinetic energy of the gas molecules. The kinetic energy of a molecule is the energy it possesses due to its motion. As the temperature of a gas increases, the average kinetic energy of the molecules increases.
If the temperature of a gas is raised from 100°C to 200°C, the average kinetic energy of the molecules will double. This is because the temperature increase is a 100% increase, and the average kinetic energy of the molecules will also increase by 100%.
It is important to note that this is only true if the volume and number of molecules in the gas are held constant. If the volume or number of molecules changes, the relationship between temperature and average kinetic energy may be different.
To Learn More About Kinetic-molecular theory
https://brainly.com/question/15013597?referrer=searchResults
It is desired to obtain 500 VAR reactive power from 230 Vrms 50 Hz 1.5 KVAR reactor. What should be the angle of the AC to AC converter to be used? Calculate the THD of the current drawn from the mains (consider up to the 12th harmonic)?
Answers
Answer:
14.5° ; THD % = 3.873 × 100 = 387.3%.
Explanation:
Okay, in this question we are given the following parameters or data or information which is going to assist us in solving the question efficiently and they are;
(1). "500 VAR reactive power from 230 Vrms 50 Hz 1.5 KVAR reactor".
(2). Consideration of up to 12th harmonic.
So, let us delve right into the solution to the question above;
Step one: Calculate the Irms and Irms(12th) by using the formula for the equation below;
Irms = reactive power /Vrms = 500/230 = 2.174 A.
Irms(12th) = 1.5 × 10^3/ 12 × 230 = 0.543 A.
Step two: Calculate the THD.
Before the Calculation of the THD, there is the need to determine the value for the dissociation factor, h.
h = Irms(12th)/Irms = 0.543/ 2.174 = 0.25.
Thus, THD = [1/ (h)^2 - 1 ] ^1/2. = 3.873.
THD % = 3.873 × 100 = 387.3%.
Step four: angle AC - Ac converter
theta = sin^-1 (1.5 × 10^3/ 12 × 500) = 14.5°.
if you want to withdraw $10000 at the end of two years and $35000 at the end of four years, how much should you deposit now into an account that pays 9% interest compounded annually?
Answers
Answer:
490000 dollars
Explanation:
With the acceleration depicted in Fig. 2, a particle travels along a straight path. Plot the v-t and x-t curves for 0 < 150 < 15s. If the particle starts from the origin with an initial velocity of vo = -14 m/s, calculate (a) the particle's maximum velocity and (b) the particle's maximum position coordinate.
Answers
Answer: Your welcome!
Explanation:
The v-t curve for this situation is shown in Figure 3. The particle starts at t=0 with an initial velocity of -14 m/s and then gradually accelerates until it reaches a maximum velocity of 16 m/s at t=15s.
The x-t curve for this situation is shown in Figure 4. The particle starts at t=0 at the origin and then gradually moves in the positive direction due to the acceleration. The maximum position coordinate of the particle is 180 m at t=15s.
(a) The particle's maximum velocity is 16 m/s.
(b) The particle's maximum position coordinate is 180 m.
To prevent the bubble from popping, a second bubble is made with more total fluid. This makes the walls of the bubble thicker.
a. True
b. False
Answers
B. False
Explanation:
It would be the same fluid and it would explode anyway
Warning danger ahead sign
Answers
Answer: okiiiii
Explanation:
Ok
Explanation
Choose the correct rewritten sentence for “Scientists have discovered that the climate of our planet is becoming warmer every year.
Answers
What is one of the reasons to consider implementing a blockchain solution?
Answers
Blockchain is often used often in the verification and locating of multistep transactions. One of the reasons to consider implementing a blockchain solution is the ability to work on different versions of the same data.
Blockchain solution is known to keep transactions safe, limit compliance costs, and speed up data transfer processing. It is known to back up the accuracy of the data.In Blockchain, all node can see all transactions that are taking place in the system and all will get a copy of each of them to update its data and approve it.
See full question below
What is one of the reasons to consider implementing a blockchain solution?
Options:
1.inability to track simultaneous updates by multiple users
2. ability to work on different versions of the same data
3.ability to verify that data has not been tampered with since its creation
4.inability to trace and access data of other users
Learn more from
https://brainly.com/question/23827936
If sin 0-cos 0 = -1/3, what is the value of sin 20?
Answers
Sin 20 degrees has a value of 0.3420201. Sin (20° /180°), often known as sin (/9) or sin 20 degrees, is expressed in radians (0.349065. . .). With the use of examples, we will go over how to calculate sin 20 degrees in this post.
What does Sin 20 Degrees Mean?Sin 20 degrees has a numeric value of 0.342020143. Sin 20 degrees can also be written as the angle (20 degrees equivalent )'s in radians (0.34906 . . .).Using the degree to radian conversion, we can determine that 20 degrees is equal to 20° (pi/180°) and that rad = /9 or 0.3490.Sin 20° is equal to sin(0.3490) = 0.3420201.Explanation of Sin 20 Degrees: The angle 20° is between 0° and 90° for sin 20 degrees (First Quadrant). Sin 20° value = 0.3420201 because sine function is positive in the first quadrant.Sine is a periodic function, therefore we may write sin 20° as sin(20° + n 360°), where n Z. Sine 20° also equals sin 380°, sin 740°, and so on.Note: Because sine is an odd function, sin(-20°) equals -sin(20°).To Learn more about Sin 20 refer to :
https://brainly.com/question/28676555
#SPJ1
what is the difference between zinc and galvanized zinc
Answers
Answer:
Both zinc plating and galvanizing is an application of zinc plating. The big difference is thickness: zinc plating is normally 0.2 mils thick. Hot dip galvanizing might be 1.0 mil thick – you get over 5 times the protection with galvanizing. ... After 20 years outdoors a galvanized product will not show signs of rust.
Explanation:
hope this helps! a brainiest is always appreciated