Suppose we have a separate chaining hash table as given in the figure below, where the hash function is h(K) = K mod 12. Fill in your answers with a single integer (e.g. 6) or a decimal number (e.g. 6.5) with NO spaces before or after. Note: checking a Null value/empty cell is not counted as a key comparion. a) The maximum number of key comparisons for a successful search is b) After inserting in the table three more keys 53, 34, and 89, the average number of key comparisons required for a successful search is c) If we use an open address hashing with linear probing to construct a hash table for the sequence of keys 37, 39, 41, 54, 92, 77, 65, 42 (in the given order) using the same hash function h(K) = K mod 12, the largest number of key comparisons in an unsuccessful search in this table is____ ; if we delete the key 54 from this hash table, then the number of key comparisons required to find 65 will be___

Embedded SQL, often known as static SQL, is a type of SQL statement that can be hard-coded into an application because it does not alter during use.

To learn more about SQL statement refer to:

https://brainly.com/question/29495392

#SPJ1

Answer: A function returns a value and a procedure just executes commands.

Explanation:

Answer:

c - returns a value.

Explanation:

on edge pls mark brainiest

The following are consequences of burning coal for energy increased levels of CO2 in the atmosphere, increased heavy metals (lead and mercury) released into the air and Acidified rain. The correct options are a, b and c.

Burning coal produces a number of main emissions: Sulphur dioxide (SO2), which causes respiratory conditions and acid rain, Nitrogen oxides (NOx), which cause respiratory diseases and smog, Particulates that cause lung sickness, respiratory diseases, fog, and haze, The main greenhouse gas produced by burning fossil fuels (coal, oil, and natural gas) is carbon dioxide (CO2).

Mercury and other heavy metals have been associated with developmental and neurological harm in both humans and other animals. Power stations produce bottom ash and fly ash as byproducts of burning coal.

Learn more about coal, here:

https://brainly.com/question/12981477

#SPJ4

Drainage divides are the lines separating two watersheds. The point on a surface where water flows out of a space is known as the exit or pour point. It is located at the watershed's lowest point.

Watershed Delineation: Using topographic maps in accordance with the fundamental tenet that water flows downward is a typical way of finding and outlining the borders of watersheds. The physical characteristics of the terrain, such as hills, valleys, basins, ridges, and channels, are depicted on a topographic map. By determining the flow direction and utilizing it in the Watershed tool, watersheds may be defined from a DEM. A raster reflecting the flow direction must first be made using the Flow Direction tool in order to identify the contributing area.

To learn more about watershed's click on the link below:

brainly.com/question/13313239

#SPJ4

The voltage at the load side is higher than the voltage at the terminals of the generator,E. The reactive power is towing from the load to the generator.

A generator is a device or machine that produces a continuous supply of energy in the form of electrical power, mechanical power, or heat. Generators can be used to power many different types of equipment, including appliances, lighting, motors, and machines. Generators can also be used as an emergency backup power source in the event of a power outage.

To learn more about generator

https://brainly.com/question/13304865

#SPJ4

The most appropriate answer is 15 feet based on the 4:1 ratio guideline. So, the correct choice is option D.

To determine the safe distance from the base of the house where Mandy should place the foot of the ladder, we can use the concept of ladder-to-wall ratio. This ratio is based on the angle at which the ladder is inclined and is crucial for ensuring stability and preventing accidents.

A commonly recommended ladder-to-wall ratio is 4:1. This means that for every four units of vertical height the ladder needs to reach, the base should be positioned one unit away from the wall. In this case, Mandy's ladder needs to reach a height of 60 feet.

Using the 4:1 ratio, we can calculate the safe distance from the base of the house as follows:

60 feet / 4 = 15 feet.

Therefore, Mandy should place the foot of the ladder approximately 15 feet away from the base of the house to ensure stability and safety while reaching the roof. This positioning allows for a proper angle of inclination and provides a stable foundation for the ladder.

Choosing a distance of 14 feet, 18 feet, or 20 feet would result in a different ladder-to-wall ratio, which may compromise stability and increase the risk of accidents.

For more questions on Foot ladder

https://brainly.com/question/30032926

#SPJ11

Answer:

\(-6111.11\ \text{kJ}\)

\(863.28\ \text{kJ}\)

Explanation:

m = Mass of automobile = 1100 kg

v = Velocity of car = 120 km/h = \(\dfrac{120}{3.6}\ \text{m/s}\)

h = Height of hill = 80 m

g = Acceleration due to gravity = \(9.81\ \text{m/s}^2\)

Change in kinetic energy

\(KE=\dfrac{1}{2}m(u^2-v^2)\\\Rightarrow KE=\dfrac{1}{2}\times 1100\times (0-(\dfrac{120}{3.6})^2)\\\Rightarrow KE=-611111.11\ \text{J}\)

Change in kinetic energy is \(-6111.11\ \text{kJ}\)

Change in potential energy is given by

\(PE=mgh\\\Rightarrow PE=1100\times 9.81\times 80\\\Rightarrow PE=863280\ \text{J}\)

The change in potential energy is \(863.28\ \text{kJ}\).

Answer:

- the force of the rope on the tugboat is 14.87 kN

- Force acting on the tugboat is 24.79 kN

Explanation:

 Given the data in the question;

tugboat increases its speed uniformly to 25 km/h

v₁ = 25 km/h = (25 × 1000) / ( 1 × 60min × 60sec )

= 25000m / 3600s

=  6.94 m/s

Now, lets determine the force on the rope using the following relation;

T = \(m_b\)v₁ / t₁

\(m_b\) is mass of barge( 75 Megagram = 75 × 10³ Kilogram  ), time t₁ is 35 s and v₁ is 6.94 m/s

so we substitute

T = [(75 × 10³) × 6.94 ]  / 35

T = 520500 / 35

T = 14871.43 N

T = 14871.43 / 1000

T = 14.87 kN

Therefore, the force of the rope on the tugboat is 14.87 kN

Now, to determine F acting on the tugboat;

\(Ft_1\) = ( \(m_t\) + \(m_b\) )\(v_1\)

we solve for F

F = ( \(m_t\) + \(m_b\) )\(v_1\) / \(t_1\)

where \(m_t\) is mass of tugboat (50 Megagram = 50 × 10³ Kilogram  )

so we substitute

F = [( (50 × 10³) + (75 × 10³) )6.94] / 35

F = [ 125000 × 6.94 ) / 35

F = 867500 / 35

F = 24785.7 N

F = 24785.7 / 1000

F = 24.79 kN

Therefore, Force acting on the tugboat is 24.79 kN

Answer:

a

Explanation:

A project that requires using a pleater, a ruffling foot, or a gathering foot is the creation of a dress.

A pleater, a ruffling foot, and a gathering foot are all accessories for sewing machines or machines themselves that help fashion designers to give the fabric a different shape or texture, and therefore create unique pieces.

All of the tools can be used in the creation of a dress, for example, a pleater can be used in the top section of the dress to give it a nice texture and make it different from the skirt. In the same way, others such as the ruffling foot or the gathering foot can be used in the sleeves of the dress.

Learn more in: https://brainly.com/question/24702927

Stability conditions refer to the set of conditions or criteria that must be met in order for a system, process, or structure to remain stable or in equilibrium. The specific stability conditions that apply to a given system or process will depend on its characteristics and the type of forces or inputs that it is subjected to.

To determine the stability conditions for k and a in the feedback system with the transfer function G(s) = k / (s^2(s^2 + as)), follow these steps:

Step 1: Find the characteristic equation
The characteristic equation is derived from the denominator of the closed-loop transfer function, which is obtained by applying the feedback formula: T(s) = G(s) / (1 + G(s)H(s)). Assuming unity feedback (H(s) = 1), the closed-loop transfer function is T(s) = G(s) / (1 + G(s)).

Step 2: Obtain the denominator of the closed-loop transfer function
For our system, the denominator is given by: D(s) = 1 + G(s) = s^4 + as^3 + ks^2.

Step 3: Apply the Routh-Hurwitz criterion
To ensure stability, all coefficients of the characteristic equation should be positive and no sign changes should occur in the first column of the Routh array. Construct the Routh array as follows:

1. Write the first two rows with the coefficients of the polynomial:
Row 1: [1, a]
Row 2: [k, 0]

2. Compute the subsequent rows using the Routh-Hurwitz formula:
Row 3: [-a/k, 0]

3. Check for sign changes in the first column:
For stability, a > 0, k > 0, and -a/k < 0. From the last inequality, it's clear that a and k cannot have the same sign.

Conclusion:
For the feedback system to be stable, the conditions on k and a are as follows:
1. a > 0
2. k > 0
3. a and k must have opposite signs.

To know more about Stability conditions visit:

https://brainly.com/question/5499741

#SPJ11

Answer:

A = 5h (B + b); solve for B.

2

sens organ is the eye example

The decision was made to develop a standard nationwide ordering system that automated cookie ordering for the Girl Scouts of the USA (GSUSA) because of its Least technical complexity. Option C

One of the key reasons was to reduce the burden on individual troops and volunteers who were previously responsible for managing cookie orders manually.

The automation of the ordering process would free up their time and enable them to focus on other important tasks.

Additionally, the new system would allow for more accurate tracking of inventory, sales, and revenue, which would help GSUSA to make better-informed decisions.

Overall, the automation of the cookie ordering system would improve efficiency, accuracy, and the experience for all involved.

Read more about cookies at: https://brainly.com/question/14252552

#SPJ1

According to ANSI standards, to indicate that an exterior wall is flush with the exterior face of the stud, you would place the extension line on the exterior face of the stud and draw it perpendicular to the wall line.

The extension line should be drawn with a gap between the end of the line and the wall line, indicating that the wall is flush with the face of the stud.

This gap should be approximately 1/16 inch and should be noted with a dimension or note indicating the gap size.

This will ensure that the drawing is clear and accurate, and that the construction team understands the details of the design.

When indicating that an exterior wall is flush with the exterior face of a stud, ANSI standards recommend using extension lines to show the relationship between the two features. Extension lines are used to extend a feature or dimension line beyond the object to which it refers and are drawn perpendicular to the feature being extended.

It's important to note that following ANSI standards is not only helpful for communication with other professionals, but it also ensures that the drawing is in compliance with industry standards and regulations.

Learn more about ANSI standards at https://brainly.com/question/14466504

#SPJ11

The reference OSHA standard requires several important characteristics of a PFAS. The employer must ensure that personal fall arrest systems (PFAs) must:

a. Limit the maximum arresting force on the employee to 1,800 pounds (8 kN). The figure used above must be based on the use of a full body harness.

From the above, we can therefore say that The reference OSHA standard requires several important characteristics of personal fall arrest systems (PFAs) as employers must reduce the maximum arresting force on the employee to 1,800 pounds (8 kN) using full body harness.

Learn more

https://brainly.com/question/15049508

a) The absolute support of item set {A, B} is the number of baskets containing both items A and B. In this case, the baskets are 1, 3, 4, and 6, so the absolute support is 4.

b) The relative support of item set {A, B} is the absolute support divided by the total number of baskets. There are 6 baskets, so the relative support is 4/6 or approximately 0.67 (rounded to two decimal places).

c) The confidence of the association rule A → B is the relative support of {A, B} divided by the relative support of A. First, calculate the relative support of A: A appears in all 6 baskets, so its relative support is 6/6 or 1. Now, divide the relative support of {A, B} (0.67) by the relative support of A (1). The confidence of association rule A → B is 0.67/1 or 0.67 (rounded to two decimal places).

Learn more about baskets  here:

https://brainly.com/question/2516050

#SPJ11

According to the basic speed law, if conditions make it unsafe to follow posted speed limits, you should:  Reduce your speed to less than the maximum posted speed limit.

The highest published speed limit in the country is 85 mph (137 km/h) and can be located only on Texas State Highway 130, a toll road that bypasses the Austin metropolitan area for long-distance traffic.

The 'rule' itself is quite straightforward: if the speed limit is (for example) 30mph, the rule notes that you won't get a speeding ticket unless you are going 10% plus 2 mph faster than the limit.

To learn more about speed limit, refer

https://brainly.com/question/19567226

#SPJ4

The relationship between the concrete compressive strength and its flexural strength and splitting tensile strength is that; these strengths are interrelated and their values are dependent on one another.

The compressive strength of concrete is defined as the maximum compressive load that can be applied on a test specimen, to fail in compression. It is expressed in MPa or psi. It is one of the most important properties of concrete and is essential in designing a structure because it defines the concrete’s ability to resist compressive stresses.

A flexural strength test is performed on concrete to determine the strength of concrete in resisting bending stresses. In other words, the test determines the ability of the concrete to withstand bending stresses without cracking. A flexural strength test is important in the design of structural elements like beams, slabs, and other such components that are subjected to bending forces.

The splitting tensile strength of concrete is determined by applying a load on a cylindrical or cubical test specimen of concrete. It is the ability of the concrete to withstand tensile forces that tend to split or rupture the test specimen. It is an important property of concrete because it defines the concrete’s ability to resist tension and shear forces.

The relationship between these three strengths of concrete is that they are interrelated and their values are dependent on one another. In general, the compressive strength of concrete is higher than its flexural strength and splitting tensile strength. However, flexural strength and splitting tensile strength are important in determining the overall strength of concrete, and they are used in the design of structural elements like beams, slabs, and other such components.

You can learn more about compressive strength at: brainly.com/question/15230572

#SPJ11

Question: "Pontoon type floating roofs shall have sufficient buoyancy to remain afloat on a liquid with a specific gravity of:"

Pontoon type floating roofs shall have sufficient buoyancy to remain afloat on a liquid with a specific gravity of A) 1.0.

Learn more about sufficient buoyancy: https://brainly.com/question/28464280

#SPJ11

We can see here that the difference between bilateral tolerances, unilateral tolerances, and limit dimensions are:

Bilateral tolerances are a type of tolerance scheme where both the upper and lower limits of a dimension are specified. While unilateral tolerances are a type of tolerance scheme where only one side of the dimension has a specified limit.

When the upper and lower limits of a dimension are stated, this form of tolerance scheme is referred to as bilateral tolerances or bilateral limits.

Limit dimensions define the maximum and minimum values that a dimension can have. They provide a range of acceptable values within which the dimension should fall.

The particular needs of the part or assembly as well as functional considerations determine the tolerancing method to be used, such as bilateral, unilateral, or limit dimensions.

The term "tolerance stack-up" describes how different tolerances in an assembly interact with one another to produce variations in the final dimensions and functionality of the assembled components.

Learn more about tolerances on https://brainly.com/question/31033614

#SPJ4

The vector (-2, 5, 0.1) is normalized with respect to unity and the matrix M=[3,0.1;-0.1,2]. The resulting normalized vectors are (-0.371, 0.927, 0.019) and (-0.365, 0.457), respectively.

To normalize the vector -2 L5J L 0.1 with respect to unity, we first find its magnitude or length:

\(||v|| = \sqrt((-2)^2 + 5^2 + 0.1^2) = \sqrt{(29.01)} \approx 5.39\)

Then we divide the vector by its magnitude:

\(v_{normalized} = (-2/5.39, 5/5.39, 0.1/5.39) \approx (-0.371, 0.927, 0.019)\)

To normalize the vector with respect to the matrix M, we need to find the inverse of M (if it exists):

\(M = [ 3 0.1 ][-0.1 2 ]\)

\(det(M) = (32) - (0.1(-0.1)) = 6.02 \neq 0\) , so M is invertible.

\(M^{-1}= (1/det(M)) * [ 2 -0.1 ]\)

\([ 0.1 3 ]\)

\(M^{-1}= [ 0.332 -0.017 ]\)

\([ 0.005 0.498 ]\)

Now we can normalize the vector with respect to M:

\(v_{normalized}_{M} = M^{-1} * v_normalized\)

\(v_{normalized}_{M} \approx(-0.365, 0.457).\)

To practice more questions about vector:

https://brainly.com/question/15519257

#SPJ11

The peak frequency deviation, minimum bandwidth, and baud for a binary FSK signal for the given frequencies are respectively;

a) 0.5 kHz

b) 9 kHz

c) 4000

1) The peak frequency deviation is gotten from the formula;

∆f = |f_m - f_s|/f_b

where;

Thus;

∆f = |38 - 40|/4

∆f = 0.5 kHz

2) The minimum bandwidth is given by the formula;

B = 2(∆f + f_b)

B = 2(0.5 + 4)

B = 9 kHz

3) For FSK signal, N = 1, and the baud is gotten from the Equation;

baud = f_b/1

f_b = 4 kbps = 4000 bps

Thus; baud = 4000/1 = 4000

Read more about peak frequency at; https://brainly.com/question/26044136

Answer:

What specific fluid goes in the windshield wipers.

Distilled water

How much to put in fluid ounces?

There should be a tiny bit more than 3/4 of the way full.

A console application typically runs via a command prompt. Hence, option B is the correct answer.

A console application typically runs via a command prompt or terminal window, where the user interacts with the application by entering commands or providing input through the keyboard and receiving output in the form of text displayed on the console.

It's important to note that the behavior of a console application can vary depending on how it is executed. For example, when running through a browser or with a GUI, the console interface may be hidden or abstracted away while still providing the underlying functionality of the application.

Learn more about command prompt here:

brainly.com/question/17051871

#SPJ4

1. The area of the enclosed property is 10,000 square feet.

2. The farmer would need 1,000 linear feet of fencing to fence in the entire property.

3. The farmer paid $20,000 for the parcel.

4. The three unidentified internal angles of the polygon are 90°, 45°, and 45°.

5. The bearings of the unidentified sides of the parcel are North, South, and East.

What is angles of the polygon?

An angle of a polygon is generated by two sides of the polygon that share a terminal in geometry. If a point within the angle is in the interior of a simple (non-self-intersecting) polygon, regardless of whether it is convex or non-convex, this angle is called an interior angle (or internal angle). Each vertex in a polygon has precisely one internal angle. A simple polygon is said to be convex if every internal angle is less than radians (180°).

To learn more about angles of the polygon
https://brainly.com/question/24966296

#SPJ13

Answer:

Explanation:

In the development of a torsion formula for a circular shaft, the following assumptions are made: Material of the shaft is homogeneous throughout the length of the shaft. Shaft is straight and of uniform circular cross section over its length. Torsion is constant along the length of the shaft.