QUESTION THREE Draw the circuit diagram of a Master-slave J-K flip-flop using NAND gates and with other relevant diagram explain the working of master-slave JK flip flop. What is race around condition? How is it eliminated in a Master-slave J-K flip-flop.
Answers
A Master-slave J-K flip-flop is a sequential logic circuit that is widely used in digital electronics. It is constructed using NAND gates and provides a way to store and transfer binary information.
The circuit diagram of a Master-slave J-K flip-flop consists of two stages: a master stage and a slave stage. The master stage is responsible for capturing the input and the slave stage holds the output until a clock pulse triggers the transfer of information from the master to the slave. The working of a Master-slave J-K flip-flop involves two main processes: the master process and the slave process. During the master process, the inputs J and K are fed to a pair of NAND gates along with the feedback from the slave stage. The outputs of these NAND gates are connected to the inputs of another pair of NAND gates in the slave stage. The slave process is triggered by a clock pulse, causing the slave stage to capture the outputs of the NAND gates in the master stage and hold them until the next clock pulse arrives. A race around condition can occur in a Master-slave J-K flip-flop when the inputs J and K change simultaneously, causing the flip-flop to enter an unpredictable state. This condition arises due to the delay in the propagation of signals through the flip-flop. To eliminate the race around condition, a Master-slave J-K flip-flop is designed in such a way that the inputs J and K are not allowed to change simultaneously during the master process. This is achieved by using additional logic gates to decode the inputs and ensure that only one of them changes at a time. By preventing simultaneous changes in the inputs, the race around condition can be avoided, and the flip-flop operates reliably.
Learn more about J-K flip-flop here:
https://brainly.com/question/32127115
#SPJ11
Related Questions
You have accumulated several parking tickets while at school, but you are graduating later in the year and plan to return to your home in another jurisdiction. A friend tells you that the authorities in your home jurisdiction will never find out about the tickets when you re-register your car and apply for a new license. What should you do?
Answers
Answer:
pay off the parking tickets
Explanation:
In the scenario being described, the best thing to do would be to pay off the parking tickets. The parking tickets stay under your name, and if they are not paid in time can cause problems down the road. For starters, if they are not paid in time the amount will increase largely which will be harder to pay. If that increased amount is also not paid, then the government will suspend your licence indefinitely which can later lead to higher insurance rates.
Rank the capacitors on the basis of the charge stored on the positive plate_ Rank from largest to smallest: To rank items as equivalent; overlap them: View Available Hint(s) Reset Help largest smallest A = 4 cm? =1nF A = 2 cm? =8 nF A = 2 cm? =4 nF A = 4 cm? C = 2 nF A =1 cm? =lnF A = 8 cm? =2 nF The correct ranking cannot be determined. Submit Previous Answers
Answers
A fixed-value capacitor known as a ceramic capacitor uses ceramic material as the dielectric. It is made of two or more layers that alternate.
Ceramic capacitors are mostly employed in devices with high stability and minimal loss. The capacitance values of these capacitors are steady with regard to the applied voltage, frequency, and temperature thanks to the devices' extremely precise findings. Ceramic capacitors are non-polarized capacitors used in timing, coupling, decoupling, and filtering applications. The ceramic capacitor has a pretty high voltage rating and can withstand both DC and AC voltage. A ceramic material serves as the dielectric medium in a ceramic capacitor. A thin coating of metal oxide serves as the dielectric medium within an electrolytic capacitor. A ceramic capacitor's corresponding series resistance is little.
To learn more about ceramic capacitor click the link below:
brainly.com/question/28999660
#SPJ4
Discuss the relation between the force exerted and pressure.
Answers
Answer:
When a force is exerted on an object it can change the object's speed, direction of movement or shape. Pressure is a measure of how much force is acting upon an area. Pressure can be found using the equation pressure = force / area. Therefore, a force acting over a smaller area will create more pressure
Explanation:
hope it will become helpful to you ☺️☺️
In Florida, a _____ curb indicates an area where parking is prohibited.
A. red
B. blue
C. green
D. yellow
Answers
It is important for drivers to be familiar with these colors and what they indicate. In Florida, a yellow curb indicates an area where parking is prohibited.
Parking rules and regulations are important to know. The laws regarding parking, however, are not always the same from state to state. For example, in Florida, parking on a yellow curb is generally prohibited. In contrast, parking on a red curb may be allowed in some states. Blue and green curbs, on the other hand, typically denote parking restrictions for a specific purpose or group of individuals. In California, for example, a blue curb indicates that parking is reserved for individuals with disabilities who have a disabled placard or plate displayed on their vehicle.
Similarly, green curbs often indicate short-term parking for loading and unloading, or parking spots reserved for electric vehicles that require charging.
The use of different colors to denote parking restrictions helps to ensure that drivers are aware of the rules and regulations regarding parking in a particular area.
Learn more about electric vehicles:
https://brainly.com/question/30714733
#SPJ11
determine the forces in members bc and fg of the loaded symmetrical truss. show that this calculation can be accomplished by using one section and two equations, each of which contains only one of the two unknowns.
Answers
The forces in members BC and FG of the loaded symmetrical truss can be determined by using one section and two equations, each of which contains only one of the two unknowns.
What is Force?
A force is an effect that can alter an object's motion according to physics. A force can cause an object with mass to accelerate when it changes its velocity, for as when it moves away from rest. An obvious way to describe force is as a push or a pull. A force is a vector quantity since it has both magnitude and direction. It is calculated using the newton SI unit (N). Force is denoted by the letter F. (formerly P).
The net force acting on an object is equal to the rate at which its momentum varies over time, according to Newton's second law in its original formulation.
The forces in members BC and FG of the loaded symmetrical truss can be determined by using one section and two equations, each of which contains only one of the two unknowns. By using the section, the force in member BC can be determined. By using the equation, the force in member FG can be determined.
To learn more about force
https://brainly.com/question/12970081
#SPJ4
both structured and unstructured documents can contain knowledge.
Answers
Yes, both structured and unstructured documents can contain knowledge. Examples of structured documents include spreadsheets, databases, and tables.
Structured documents have a specific format or organization, making it easier to access and understand the knowledge within.Unstructured documents, on the other hand, do not have a specific format or organization, making it more difficult to access and understand the knowledge within. Examples of unstructured documents include emails, articles, and social media posts.Both types of documents can hold valuable knowledge, but the way this knowledge is organized and presented differs between structured and unstructured documents.
https://brainly.com/question/31454431
#SPJ11
What lives at layer 3 (the network layer) of the OSI model?
Answers
Layer 3 of the OSI (Open Systems Interconnection) model, known as the network layer, is responsible for providing end-to-end communication between hosts in different networks.
The network layer is responsible for routing and forwarding data packets across different networks, as well as handling addressing and logical connectivity.
The main entities that live at layer 3 (the network layer) of the OSI model include:
Routers: Routers are network devices that operate at the network layer and are responsible for forwarding data packets between different networks. They use routing tables and protocols to determine the best path for data packets to reach their destination across multiple networks.
IP (Internet Protocol): IP is a network layer protocol that provides logical addressing and routing functionality. It is responsible for assigning unique IP addresses to devices on a network, and for routing data packets based on those IP addresses.
ICMP (Internet Control Message Protocol): ICMP is a network layer protocol that is used for sending error messages and operational information about network conditions. It is often used for diagnostic purposes, such as ping and traceroute, to check the connectivity and status of network devices.
Network Addressing: Layer 3 is also responsible for assigning and managing IP addresses, which are used to uniquely identify devices on a network.
Subnetting and VLANs: Layer 3 may also involve subnetting and VLANs (Virtual Local Area Networks), which are used for network segmentation and management to improve efficiency and security.
In summary, layer 3 of the OSI model includes routers, IP, ICMP, network addressing, and other protocols and technologies that are responsible for routing, addressing, and logical connectivity in a network.
learn more about OSI here:
https://brainly.com/question/25404565
#SPJ11
what is a computer device
Answers
NEED A CHEN NOTATION DIAGRAM OF THE FOLLOWING INFORMATION
***** This is a Chen Notation ER Diagramming Assignment. Only Chen Notation Diagrams will be accepted. *****
During peak periods, the Temporary Employment Corporation (TEC) places temporary workers in companies. TEC’s manager gives you the following description and business rules of the business:
TEC has a file of candidates who are willing to work. They would like to put this Candidate File Information into a Database.
If the candidate has worked before, that candidate has a specific job history. (Naturally, no job history exists if the candidate has never worked.) Each time the candidate works temporarily for an outside company, one additional job history record is created. TEC wants the candidate's Job History in a database.
Each candidate has earned several qualifications. Each qualification may be earned by more than one candidate. (For example, it is possible for more than one candidate to have earned a BBA degree or a Microsoft Network Certification. And clearly, a candidate may have earned both a BBA and a Microsoft Network Certification.) TEC wants to store all existing and future types of Qualifications in a database.
TEC offers courses to help candidates improve their qualifications. This is done by offering training courses so that candidates can earn qualifications. TEC wants to keep store all courses that they offer for qualifications in a Database
Every course develops one specific qualification; however, TEC does not offer a course for every qualification. Some qualifications have multiple courses that develop that qualification.
Some courses cover advanced topics that require specific qualifications as prerequisites. Some courses cover basic topics that do not require any prerequisite qualifications. A course can have several prerequisites. A qualification can be a prerequisite for more than one course.
TEC also has a list of companies that request temporary employees.
Each time a company requests a temporary employee, TEC makes an entry in the Openings folder. That folder contains an opening number, a company name, required qualifications, a starting date, and anticipated ending date, and hourly pay. TEC wants to store all company requests for temporary jobs in a database.
When a candidate matches the qualification, the job is assigned, and an entry is made in the Placement Record folder. That folder contains an opening number, a candidate number, the total hours worked, etc. In addition, an entry is made in the job history for the candidate.
An opening can be filled by many candidates, and a candidate can fill many openings.
Summary Information that has to be Maintained
Client Company Information. These are companies that need Temporary Workers.
Job Opening Information, a Company offers one or more Temporary Job-Opening Positions
Qualification or Skills of the Candidates in (TEC). A Candidate can have one or more Qualifications
Candidate or Temporary Worker Information. A Candidate is a Temporary Worker seeking a position
Candidate JOB_HISTORY Information. This is a Temporary Workers Work History.
Placement Information. This is the Record of all Temporary Workers Placed in a Temporary Job
Training Courses that are being offered to (TEC) Candidates.
Training Courses that Candidates have taken
Given that information, do the following:
Draw the Chen ERDs for this enterprise
Identify all Entities
Identify all Attributes for the Entities
Identify all possible relationships
Identify the Cardinality for each relationship
Resolve all 1: N relationships
Resolve all M: N relationships
Identify Primary Keys and map the Foreign Keys based on the described Cardinality
Answers
The ER diagram for the Temporary Employment Corporation (TEC) based on the business rules given is given below: Attributes for Entities:
(One-to-Many)One candidate can have many job histories. (One-to-Many)One job history can belong to only one candidate. (One-to-One)One placement can belong to only one candidate. (One-to-One)One job opening can be placed by many placements. (One-to-Many)One candidate can have many placements.
In the given diagram below, all the relationships and primary keys are labeled correctly and the ER diagram is resolved for all M:N relationships and 1:N relationships. If you want to add more attributes to each entity, you can do it accordingly:
To know more about Employment visit:
https://brainly.com/question/17459074
#SPJ11
A helicopter landing pad is to be constructed over an area of 40 ft by 70 ft. It is to be 2 ft thick. How many cubic feet must be ordered?
Answers
The volume of cuboid in cubic feet which must be ordered is equal to 5,600 cubic feet.
Given the following data:
Length of helicopter landing pad = 40 ft.
Width of helicopter landing pad = 70 ft.
Height or thickness of helicopter landing pad = 2 ft.
How to calculate the volume of a geometric figure?Based on the information provided, we can reasonably infer and logically deduce that the shape of this helicopter landing pad is a cuboid.
Mathematically, the volume of a cuboid can be calculated by using this following formula:
Volume = l × w × h
Where:
l represents the length of a cuboid.w represents the width of a cuboid.h represents the height of a cuboid.Substituting the given parameters into the formula, we have;
Volume = 40 × 70 × 2
Volume = 5,600 cubic feet.
Read more on volume of a cuboid here: https://brainly.com/question/24919497
#SPJ1
1 A power transmission includes a belt drive, a chain drive and a gear drive. Which of the following is the best arrangement between a motor and a working machine? (a) belt drive gear drive chain drive (b) chain drive gear drive belt drive (c) belt drive chain drive gear drive (d) chain drive belt drive gear drive
Answers
Answer:d
Explanation:
(d) chain drive belt drive gear drive
The chain drive belt drive gear drive. Thus option D is correct.
Waht is power trasmisson ?The power transmission includes the bulk of the electrical energy form the generating sites such as the power station or the power plant and send to the anelectric substation where the voltage gets transformed and distributed to the insurers on other substations.
They can be mechanical, electrical and hydrologic, etc. The power transmission can move the electricity over larger distances.
Find out more information about the transmission.
brainly.com/question/13142496
Which term best describes the component that touches the edge of a cam?
Answers
Follower is the component that touches the edge of a cam.
What is CAM computer aided manufacturing?Automating a production process via the use of software and computer-controlled equipment is known as computer aided manufacturing (CAM). According to that definition, a CAM system requires the following three elements to operate: Software that creates toolpaths to instruct a machine on how to build a product.Applications for CAD/CAM are used to develop products and control manufacturing processes, particularly CNC machining. Models and assemblies made with CAD software, such as Fusion 360, are used by CAM software to develop toolpaths that operate machine machines to turn designs into actual components.The use of software to manage machine tools during the creation of work parts is known as computer-aided manufacturing, also referred to as computer-aided modelling or computer-aided machining.Learn more about Computer aided manufacturing refer to :
https://brainly.com/question/13201484
#SPJ1
what could happen if the engine was uncowled during the starting and operating procedures
Answers
If an engine fails during rollout or just before takeoff, immediately shut both throttles and land the aircraft safely. Before reaching a safe single engine speed right away after takeoff, drop your nose to increase velocity.
What is the engine starting procedure?Closing the throttle, turning off the fuel pump, setting the mixture control to idle cutoff, and simply cranking the engine is the most reliable hot start method I've found.
What is the procedure for engine failure?If an engine fails during rollout or just before takeoff, immediately shut both throttles and land the aircraft safely. Before reaching a safe single engine speed right away after takeoff, drop your nose to increase velocity. If you are unable to climb, close both throttles and land straight ahead.
What happens if engine fails during take off?The typical practice for the majority of aircraft would be to abandon takeoff if an engine failed during takeoff. In small aircraft, the pilot should turn the throttles down to idle, activate the speed brakes (if provided), and apply the brakes as needed if the engine fails before VR (Rotation Speed).
To learn more about engine procedure refer to:
https://brainly.com/question/18428188
#SPJ1
For an Ac signal with peak voltage Vp equal to 60V, the same power would be delivered to a load with a dc voltage of
Answers
Answer:
30√2 ≈ 42.426 volts
Explanation:
The RMS value of the signal is the DC equivalent. For a sine wave, the mean of the square is half the square of the peak value. Then the Root-Mean-Square is ...
RMS = √((Vp)^2/2) = Vp/√2
For Vp = 60 volts, the equivalent DC voltage is ...
V = (60 volts)/√2 = 30√2 volts ≈ 42.426 volts
binary classification algorithm
Answers
Answer:
What is this exactly?
Explanation:
If your asking for the definition, binary classification is the task of classifying the elements of a set into two groups on the basis of a classification rule.
12. Explain types of Social Engineering? Human-based, Computer-based, Mobile-based.
Answers
Social engineering is the act of manipulating people to disclose sensitive information, such as passwords or credit card numbers.
There are three main types of social engineering which include:Human-based Computer-based Mobile-based Explanation:
1. Human-based:Human-based social engineering involves tricking people into revealing sensitive information such as passwords and usernames.
2. Computer-based:Computer-based social engineering involves manipulating people using technology, such as phishing scams and other fraudulent messages. This type of social engineering is usually carried out over the internet.
3. Mobile-based:Mobile-based social engineering involves tricking people into installing malware or other harmful software on their mobile devices. This can include fake apps, phishing messages, or other fraudulent sch
Learn more about Social engineering at
brainly.com/question/30514468
#SPJ11
1. Human-based social engineering: This type of social engineering technique is carried out through personal interactions. 2. Computer-based social engineering: This type of social engineering technique is carried out using the Internet. 3. Mobile-based social engineering: This type of social engineering technique is carried out through mobile devices such as smartphones and tablets.
Social Engineering is a technique used by attackers to manipulate people into disclosing sensitive information, clicking on malicious links, or performing actions that may lead to compromising a system or network. There are different types of social engineering techniques, including
1. Human-based social engineering: This type of social engineering technique is carried out through personal interactions, such as phone calls, emails, or face-to-face interactions. It aims to trick or persuade individuals into divulging confidential information.
2. Computer-based social engineering: This type of social engineering technique is carried out using the Internet or other computer-related technologies. Examples of computer-based social engineering techniques include phishing, watering hole attacks, and baiting.
3. Mobile-based social engineering: This type of social engineering technique is carried out through mobile devices such as smartphones and tablets. Examples of mobile-based social engineering techniques include SMS phishing and fake apps.
Read more about Social Engineering at https://brainly.com/question/32631468
#SPJ11
FILL IN THE BLANK. The voltage measured after the motor is started should ______ the incoming voltages with each method of reduced voltages starting
A. Be greater than
B. Be less than
C. Equal
D. None of the above
Answers
The voltage measured after the motor is started should be less than the incoming voltages with each method of reduced voltages starting. Therefore, the correct option is (B) Be less than.
When a motor is started using a reduced voltage starting method, such as autotransformer or star-delta starting, the voltage applied to the motor is reduced compared to the incoming voltage.
This is done to limit the inrush current and reduce the mechanical stress on the motor during starting.
As the motor starts to accelerate and reach its rated speed, the voltage applied to the motor is gradually increased until it reaches its full rated voltage.
At this point, the voltage measured after the motor is started should be less than the incoming voltage, as some voltage is dropped across the motor windings and other components in the starting circuit.
Therefore, the correct answer is B.
"The voltage measured after the motor is started should be less than the incoming voltages with each method of reduced voltages starting".
For more such questions on Voltage:
https://brainly.com/question/28632127
#SPJ11
The answer to the question is what the
Answers
what's the voltage supplied to the light fixtures in the communication room of the manufacturing facility?
a.208V
b.120V
c.277V
d.480V
Answers
The voltage supplied in the communication room to the light fixtures can be 120 volts or 277 volts respectively.
Options B and C are the correct answers.
What is voltage?
Voltage is the electric force that makes the charges move which creates an electric current.
The light fixtures are the component of light that is being attached to the wall or a ceiling that holds any kind of lighting element. For instance, the holder of a bulb in which it is fixed is treated as a light fixture. The general voltage produces by a light fixture is 120 volts but preferable should be at 277 volts.
Therefore, all the volts except which is mentioned in options A and D cannot correspond to the voltage of light fixtures.
Learn more about the voltage in the related link:
https://brainly.com/question/2364325
#SPJ1
Lydia is the CEO for a large pharmaceutical manufacturer. Her company is in the final stages of FDA
approval for a new drug for diabetics. The new drug is expected to bring in billions of dollars for the company. Lydia is acquainted with Bradley,
the CSHO on rotation for OSHA inspections. Lydia is concerned that a surprise inspection may turn up violations, which could affect the launch of
the drug. Lydia reaches out to Bradley and casually mentions that it would be helpful if he could tell her when the next OSHA inspection will be
Should Bradley give Lydia advance notice about an upcoming inspection?
No, because he could receive fines and a jail term.
No, because this situation does not meet the criteria for advance notice.
Yes, because employers may request an OSHA inspection at any time.
Yes, because the inspection will be conducted during regular business hours.
Answers
It is a criminal offense for any person to give unauthorized advance notice of an OSHA inspection.
How much land would a solar field take up to produce 1000 megawatts of power
Answers
It would need 32 acres of land to produce 1,000 megawatts of power.
a strut of length l has its ends built into a material which exerts a constraining couple equal to k times the angular rotation in radians. show that the buckling load p is given by the equation
\( \tan( \alpha )l \div 2 = p \div \alpha k \: \: and \: \: \alpha { \}^{2} \)
\( \alpha \)
Answers
Answer:
fxruwrisris84drid85d59s59e95etod
Explanation:
urzrjxrjxrjr
68dtudrusditxx4ixtiurzrjzruzurzjfzirzjrz
An eyewash station should be located within what maximum distance from every location where a person may come into contact with substances that can cause damage to the eyes?
Answers
An eyewash station should be located within a maximum distance of 25 feet from every location where a person may come into contact with substances that can cause damage to their eyes.
______________ measures how well a window allows heat from the sunlight
Answers
Solar heat gain coefficient (SHGC) measures how well a window allows heat from the sunlight to pass through it.
The solar heat gain coefficient (SHGC) is a value that represents the amount of solar radiation, in the form of heat, that can pass through a window or glazing system. It measures the ability of the window to transmit solar energy from the sunlight into the interior space. A higher SHGC indicates that the window allows more solar heat to pass through, which can contribute to increased solar heat gain and potentially higher cooling loads. On the other hand, a lower SHGC indicates that the window has better heat-blocking properties, reducing the amount of solar heat entering the building and potentially lowering cooling needs. The SHGC is an important factor to consider when selecting windows for energy efficiency and managing indoor thermal comfort.
Know more about Solar heat gain coefficient here:
https://brainly.com/question/30709166
#SPJ11
(premium) of your put opticui? 23. (1 point) If the S0(KD/S)=0,302 and S0(KDid)=0.395. What is Se (E/S)? 24. (1.5 points) If the interest rate in the U.K is 2% and the interest rate in Germany is 3% current S0(f∈) is 0.86. According to Interest Rate Parity, what is F1 (£) € )?
Answers
Answer:
Apologies, but I couldn't quite understand your first question regarding "put opticui". As for your second question:
Interest Rate Parity (IRP) states that the difference in interest rates between two countries will determine the exchange rate between their currencies. Specifically, if the interest rate in one country is higher than the other, the currency of the country with the higher interest rate will depreciate relative to the currency with the lower interest rate.
Given the current spot exchange rate of S0(f∈) = 0.86, the interest rate in the UK of 2%, and the interest rate in Germany of 3%, we can use the following formula to calculate the forward exchange rate (F1 (£/€)):
F1 (£/€) = S0(f∈) x (1 + id) / (1 + if)
where id is the interest rate in Germany and if is the interest rate in the UK. Plugging in the given values, we get:
F1 (£/€) = 0.86 x (1 + 0.03) / (1 + 0.02) = 0.8776
Therefore, according to Interest Rate Parity, the forward exchange rate of F1 (£/€) is 0.8776.
Explanation:
beginning from rest, an object of mass 200 kg slides down a 10-m-long ramp. the ramp is inclined at an angle of 408 from the horizontal. if air resistance and friction between the object and the ramp are negligible, determine the velocity of the object, in m/s, at the bottom of the ramp. let g 5 9.81 m/s2.
Answers
The given problem involves a 200 kg object sliding down a 10-meter-long ramp inclined at an angle of 40 degrees from the horizontal. As air resistance and friction are negligible, we can use the conservation of mechanical energy to solve for the object's velocity at the bottom of the ramp.
Initially, the object has only potential energy due to its height, which can be calculated as h = 10 * sin(40°). The potential energy (PE) is given by the formula PE = mgh, where m = 200 kg, g = 9.81 m/s², and h is the height.
When the object reaches the bottom of the ramp, all its potential energy is converted into kinetic energy (KE), which is given by the formula KE = (1/2)mv², where m = 200 kg and v is the final velocity in m/s.
Using conservation of mechanical energy, we equate the potential energy and kinetic energy: mgh = (1/2)mv². We can cancel the mass (m) from both sides of the equation and solve for the final velocity (v).
After calculating the height and solving the equation for v, you will find the object's velocity at the bottom of the ramp in m/s. Remember to maintain accuracy and professionalism when presenting your final answer.
Learn more about mechanical here
https://brainly.com/question/30403434
#SPJ11
If one branch of a parallel circuit is defective, how will total circuit current be affected
Answers
A parallel circuit is a type of electrical circuit where multiple branches are connected to a common voltage source. Each branch provides its own path for the current to flow. In the case of a parallel circuit, if one branch becomes defective, the total circuit current will not be affected.
This is because the current will simply follow the remaining branches and continue to flow as normal. The current in a parallel circuit is determined by the voltage and the resistance in each branch. When one branch becomes defective, the resistance in that branch will increase, but this will not affect the overall current in the circuit. Instead, the remaining branches will compensate for the increased resistance by providing more current to the circuit.
In summary, if one branch of a parallel circuit is defective, the total circuit current will not be affected. The remaining branches will continue to provide the necessary current to the circuit, and the overall resistance of the circuit will increase due to the faulty branch.
You can learn more about parallel circuits at: brainly.com/question/26589211
#SPJ11
Write a short C/C++ program that reads a 64-bit machine instruction as a hex integer and extracts the values for its components from certain bits, specified left-to-right, as follows:
Bits 0-4 code (the instruction code)
Bits 5-8 ladrm (left address mode)
Bits 9-12 radrm (right address mode)
Bits 13-19 si (short immediate)
Bits 20-25 lreg (left register)
Bits 26-31 rreg (right register)
Bits 32-63 li (long immediate)
You will read 16 hexadecimal digits, such as 08800080000004D2, which represent the numeric value of the 64 bits to be analyzed. The output for this input string should be:
Instruction: 08800080000004D2
rreg = 0
lreg = 2
si = 0
radrm = 0
ladrm = 1
code = 1
li = 1234
Note that the output numbers are base 10, not hexadecimal. To get full credit for this program, you’ll need to use a union with a nested bit-field structure in C/C++(use no bitwise operators). If you’re using an Intel machine, remember that it is a little-endian machine, which means you’ll have to reverse the order of the bit-field declarations to extract the correct values. Use the following input strings to test your program:
08800080000004D2
E05000000000008E
1140408300000000
5008000300000000
E800000000000020
Here is a main program to use:
int main( ) {
unsigned long long x;
while (cin >> hex >> x) {
cout << "Instruction: " << hex << x << endl;
cout << dec; // Convert back to decimal
readStuff(x);
cout << endl;
}
}
For all programming problems, be sure to submit your source code and a copy/screen shot of the execution output. No executables or project files, please.
Answers
We now know that 25 registers, or 32 registers, can be accessed because the register field's size is 5 bits.
The smallest unit of information that may be stored or transferred, the bit is a simplification for the binary digit, which can only have two values: 0 or 1, true or false, and so on. Organizing the information as follows: bits 16 through 11 and bits 31 through 26 of register $t1 are down from register $t0 by 11 bits. With this data organized, we have: R1,R1,$0 ; And the contents of R0 with 0 to clear R1 R0,R0,0xFC00 ; Load R0 with 0xFC00. R0, R0,$0 ; And the contents of R0 with 0 to clear R0 The updated components are: R1, R1,0xFC00 in ADDI; Put 0xFC00 SLL R1, R1, and 0x10 into R1; R1 should be rotated 16 degrees to the left to become 0xFC000000 NOR. R1,R1,$0 ; To make R1 equal to 0x03FFFFFF AND R1,R1,$t1, invert all of R1's bits.
Learn more about The bit here:
https://brainly.com/question/15213870
#SPJ4
Which type of container traps the most heat a shoe box covered in aluminum foil plastic wrap or wax paper?
Answers
The container that traps the most heat is a shoebox covered in aluminum foil.
What is the use of aluminum foil?An aluminum foil is used for food storage, and to wrap items, such as meats, to minimize moisture loss while cooking.
Aluminum foil is also an excellent insulator. This is due to the fact that it reduces heat emission by reflecting it back.
Therefore, in a shoebox container, the aluminum foil helps to trap most heat better than a plastic wrap or wax paper.
Learn more about aluminum foil here:
https://brainly.com/question/277354
#SPJ2
In Fig. A-3, a force F passing through C produces a clockwise moment of 600 ft-lb about A and a counterclockwise moment of 300 ft-lb about B. Determine the moment of F about O.
Answers
The moment of the force about the zero origin (0,0) is 670.82 ft-lb.
The given parameters:
Clockwise moment about A = 600 ft-lbCounterclockwise moment about B = 300 ft-lbThe moment of the force about the zero origin (0,0) is calculated as follows;
\(P^2 = P_y^2 + P_x^2\\\\\)
where;
\(P_y\) is the clockwise moment
\(P_x\) is the counterclockwise moment
\(P = \sqrt{600^2 + 300^2} \\\\P = 670.82 \ ft-lb\)
Thus, the moment of the force about the zero origin (0,0) is 670.82 ft-lb.
Learn more about moment of force here: https://brainly.com/question/6278006