My goal is to make a GPS tracker using THE PARTICLE ARGON BOARD and the NEO 6M GPS MODULE
I need help creating a code for the NEO 6M GPS MODULE to be UPLOADED TO THE PARTICLE ARGON BOARD in the PARTICLE WEB IDE
i dont know why but, #include DOESNT WORK in the PARTICLE WEB IDE
PLEASE INCLUDE WHERE WILL THE LOCATION DATA BE SEEN AT AND THE CODE
#include does not work in particle
Answers
To create a GPS tracker using the Particle Argon board and the NEO 6M GPS module in the Particle Web IDE, you need to write a code that communicates with the GPS module and retrieves location data.
However, the Particle Web IDE does not support the #include directive for including external libraries. Therefore, you will need to manually write the necessary code to interface with the GPS module and extract the GPS data. The location data can be seen either through the Particle Console or by sending it to a server or a cloud platform for further processing and visualization.
In the Particle Web IDE, you cannot directly include external libraries using the #include directive. Instead, you will need to manually write the code to communicate with the NEO 6M GPS module. Here are the general steps you can follow:
1.Initialize the serial communication with the GPS module using the Serial object in the Particle firmware.
2.Configure the GPS module by sending appropriate commands to set the baud rate and enable necessary features.
3.Continuously read the GPS data from the GPS module using the Serial object and parse it to extract the relevant information such as latitude, longitude, and time.
4.Store or transmit the GPS data as required. You can either send it to a server or cloud platform for further processing and visualization or display it in the Particle Console.
It's important to note that the specific code implementation may vary depending on the library or code examples available for the NEO 6M GPS module and the Particle Argon board. You may need to refer to the datasheets and documentation of the GPS module and Particle firmware to understand the communication protocol and available functions for reading data.
To learn more about GPS tracker visit:
brainly.com/question/30652814
#SPJ11
Related Questions
) A regenerative vapor power cycle has three turbine stages with steam entering the first stage at 2500 lbf/in2 , 1100 o F. The cycle has two feedwater heaters, a closed feedwater heater using extracted steam at 500 lbf/in2 and an open feedwater heater operating at 50 lbf/in2 . Saturated liquid condensate drains from the closed feedwater heater at 500 lbf/in2 and passes through a trap into the open heater. The feedwater leaves the closed heater at 2500 lbf/in2, 478 o F. Saturated liquid leaves the open heater at 50 lbf/in2 and the condenser pressure is 1 lbf/in2 . For isentropic operation of the turbines and pumps, determine the efficiency of this cycle.
Answers
Answer:
do the wam wam
Explanation:
Technician A says that charging system testing requires that the battery be at least 75% charged. Technician B says that a digital multimeter can not be used to test charging system voltage. Who is right
Answers
A digital multimeter can not be used to test charging system voltage,So Technician A and Technician B is not correct.
Neither technician is entirely correct.
Technician A is partially correct in that it is generally recommended to have a battery that is at least 75% charged before testing the charging system. However, this is not an absolute requirement, and some testing can still be performed with a battery that has a lower charge.
Technician B is incorrect in stating that a digital multimeter cannot be used to test charging system voltage. In fact, a digital multimeter is one of the most commonly used tools for this purpose, and it can provide accurate readings of the voltage output from the alternator.
Therefore, the correct answer is neither A nor B.
For such more questions on digital multimeter
https://brainly.com/question/29512413
#SPJ11
A major contributor to product defects in electronic modules relates to stresses induced during thermal cycling (intermittent heating and cooling). For example, in circuit cards having active and passive components with materials of different thermal expansion coefficients, thermal stresses are the principal source of failure in component joints, such as soldered and wired connections. Although concern is generally for fatigue failure resulting from numerous excursions during the life of a product, it is possible to identify defective joints by performing accelerated thermal stress tests before the product is released to the customer. In such cases, it is important to achieve rapid thermal cycling to minimize disruption to production schedules.
A manufacturer of circuit cards wishes to develop an apparatus for imposing rapid thermal transients on the cards by subjecting them to forced convection characterized by a relation of the form Nuj = CRemPr", where m=0. 8 and n=0. 33. However, he does not know whether to use air (k = 0. 026 W/mK, v= 1. 6x105m²/s, Pr=0. 71) or a dielectric liquid (k=0. 064 W/m-K, v= 109 m²/s, Pr=25) as the working fluid. Assuming equivalent air and liquid velocities and validity of the lumped capacitance model for the components, obtain a quantitative estimate of the ratio of the thermal time constants for the two fluids.
Required:
What fluid provides the faster thermal response?
Answers
A manufacturer of circuit cards aims to develop an apparatus for subjecting them to rapid thermal transients using forced convection, characterized by the relation Nuj = CRemPr^m, where m = 0.8 and n = 0.33.
To achieve rapid thermal cycling and minimize disruption to production schedules, the manufacturer needs an apparatus that can impose controlled thermal stresses on the circuit cards. Forced convection, which involves the movement of fluid (air or liquid) over the surface of the cards, is an effective method for achieving rapid heat transfer.
The relation Nuj = CRemPr^m is a dimensionless correlation equation known as the Nusselt number correlation. It relates the Nusselt number (Nu) to the Reynolds number (Re) and the Prandtl number (Pr). The Nusselt number represents the convective heat transfer coefficient, which determines the rate of heat transfer between the fluid and the surface. The Reynolds number characterizes the flow regime, indicating whether the flow is laminar or turbulent, while the Prandtl number represents the ratio of momentum diffusivity to thermal diffusivity of the fluid.
In the given relation, the values of m = 0.8 and n = 0.33 determine the correlation exponents. These values have been determined through experimental data and are specific to the system being studied. The manufacturer needs to determine the appropriate values of the constant C based on the specific conditions and characteristics of their apparatus and circuit cards.
By using the Nuj = CRemPr^m relation, the manufacturer can design and optimize their thermal cycling apparatus to achieve the desired rapid thermal transients. This will allow them to perform accelerated thermal stress tests on the circuit cards, identifying any defective joints or potential failure points before the product is released to the customer. Implementing such tests in the manufacturing process will help ensure the reliability and quality of the electronic modules, reducing the risk of failures caused by thermal cycling-induced stresses.
Learn more about manufacturer here
https://brainly.com/question/29054304
#SPJ11
The flow between two infinitely flat parallel plates displays a parabolic profile, and is called plane Poiseulle flow.
a. True
b. False
Answers
Answer:
a. True
Explanation:
The study of fluids in a state of rest or in motion and the forces involved in it is called fluid mechanics. Fluid mechanics has a wide range of applications in the field of mechanical engineering as well as civil engineering.
When we study the flow of fluid between any two flat plates that is indefinitely flat and is parallel, the flow of the fluid is known as plane Poiseulle flow. The profile of a plane Poiseulle flow is parabolic.
The velocity profile of a plane Poiseulle flow is :
\($\frac{u(y)}{U_{max}}=1-\left(\frac{2y}{h}\right)^2$\)
Thus the answer is TRUE.
A 3-phase, 460 V, 100 hp, 60 Hz, six-pole induction machine operates at 3% slip (positive) at full load. (a) Determine the speeds of the motor and its direction relative to the rotating field. (b) Determine the rotor frequency. (c) Determine the speed of the stator field. (d) Determine the speed of the air gap field. (e) Determine the speed of the rotor field relative to: (i) the rotor structure. (ii) the stator structure. (iii) the stator rotating field.
Answers
The speed of the rotor field relative to the stator rotating field is also equal to the slip speed, which is 36 RPM.
How to solve for the values(a) The synchronous speed (N_s) of the motor can be determined by the formula:
N_s = 120f / P
Where:
f = frequency (60 Hz)
P = number of poles (6)
Substituting the values, we get:
N_s = (120 * 60) / 6 = 1200 RPM
The slip (S) is given as 3%, or 0.03. The speed of the motor (N) can be determined by the formula:
N = N_s * (1 - S)
Substituting the values, we get:
N = 1200 * (1 - 0.03) = 1164 RPM
The motor is rotating in the same direction as the rotating field, because the slip is positive.
(b) The rotor frequency (f_r) can be determined by the formula:
f_r = S * f
Substituting the values, we get:
f_r = 0.03 * 60 = 1.8 Hz
(c) The speed of the stator field is equal to the synchronous speed. Therefore, it is 1200 RPM.
(d) The speed of the air gap field is also equal to the synchronous speed. Therefore, it is 1200 RPM.
(e) (i) The speed of the rotor field relative to the rotor structure is zero, because the rotor field is stationary in the reference frame of the rotor.
(ii) The speed of the rotor field relative to the stator structure is equal to the slip speed, which is the difference between the synchronous speed and the rotor speed. Therefore, it is 1200 - 1164 = 36 RPM.
(iii) The speed of the rotor field relative to the stator rotating field is also equal to the slip speed, which is 36 RPM.
Read more on synchronous speed here https://brainly.com/question/31605298
#SPJ4
18) Technician A says that adjustable wrenches should be used when
torquing fasteners. Technician B says that adjustable wrenches can round
the edges of fasteners. Which technician is correct?
A) Technician A only
B) Technician B only
O C) Both technicians
D) Neither technician
Answers
Blood pressure values are often reported to the nearest 5 mmHg(100,105,110,etc.). The actual blood pressure values for nine randomly selected individuals are given below.
128.6 , 137.4, 148.4, 140.0, 123.7, 132.0, 141.5, 143.2
What is the median of the reported blod pressure values?
Answers
According to the question the median of the reported blood pressure values is 137.5.
What is median?Median is a measure of central tendency used in statistics to identify the middle value of a set of numbers. It is calculated by arranging the values of the dataset in ascending or descending order and choosing the one in the middle.
The median of the reported blood pressure values is 137.5. To calculate the median, we first need to arrange the data in order from least to greatest.
128.6, 123.7, 132.0, 137.4, 140.0, 141.5, 143.2, 148.4
Next, we find the middle number of the data set. There are nine numbers, so the middle number is the fifth number, which is 140.0. Since the values are reported to the nearest 5 mmHg, the median is reported as 137.5, which is the nearest 5 mmHg to 140.0.
To learn more about median
https://brainly.com/question/30408777
#SPJ4
What is the optional vacuum cup mount bracket for the control head of a yaesu ftm-400dr?.
Answers
The Yaesu MMB-98 vacuum mount is an optional accessory for the Yaesu FTM-400DR control head.
What does Yaesu ftm - 400dr mean?The FTM-400DR is the first mobile phone to be introduced as a radio partner for the YAESU System Fusion Dual Mode system. When compared to other FDMA digital modulation schemes, C4FM provides superior communication quality.
The GM (group monitor) function checks the current operating frequency to see if there are any other stations in the DN mode and within communication range.
FTM is used to collect network fees such as transaction fees and fees associated with the deployment of smart contracts or the creation of new networks. Without a minimum barrier, the network would be an easy target for spam, causing performance problems and cluttering the ledger.
To learn more about YAESU refer to :
https://brainly.com/question/29414438
#SPJ4
D
Question 7
Commercial photographers attempt to produce images that will blend in and make little impact on
the public.
O True
False
1 pts
A
Answers
False. Commercial photographers attempt to produce images that will stand out and make a big impact on the public.
What is photographers?
A photographer often works as a freelancer, getting hired by different customers for specialised tasks. A client who hires a part-time or freelance photographer is expected to adhere to their every demand, as well as to put up a business strategy that makes options and price readily visible and understandable.
Photographers are in charge of the digital and physical development of their photos, as well as any or all editing that may be necessary. Simple cropping, adding/changing colours and shading, modifying sharpness and lighting, or deleting things to tidy up the image are all examples of editing techniques.
To learn more about photographers
https://brainly.com/question/28081565
#SPJ1
A ball is thrown from A.
If it is required to clear the wall at B and R = 15 ft , determine the minimum magnitude of its initial velocity vA.
Answers
The initial velocity of the ball is 29.6 ft/s given that it has to clear the wall at point B.
What is a projectile?A projectile is a body that is thrown or projected into the air, and that body moves through the air under the influence of gravity in a curved path or trajectory. When an object moves through the air, it is said to be a projectile.
The motion of a projectile can be analyzed using the equations of kinematics, which describe how the position, velocity, and acceleration of a moving object change over time. The horizontal and vertical components of the velocity and acceleration of a projectile can be calculated separately and then combined to describe the motion of the projectile.
The figure given shows that a ball is thrown from A, and it is required to clear the wall at point B, where R = 15 ft.
To determine the minimum magnitude of its initial velocity vA, we can use the range formula for a projectile. The range formula is given by:
R = (V² sin 2θ) / g
where
R is the range, V is the initial velocity, θ is the angle of projection, and g is the acceleration due to gravity, which is 32.2 ft/s².The angle of projection θ can be taken as 45 degrees because it gives the maximum range. Substituting these values in the range formula and solving for V, we get:
15 = (V² sin 90°) / 32.2V² = 15 × 32.2V = sqrt(15 × 32.2)V = 29.6 ft/sTherefore, the minimum magnitude of its initial velocity vA is 29.6 ft/s given that it has to clear the wall at point B.
Learn more about projectile: https://brainly.com/question/24216590
#SPJ11
how to find the roots of a polynomial of degree 3; finding zeros of a polynomial function; how to find the roots of a polynomial of degree 3 calculator; how to find zeros of a polynomial algebraically; zeros of polynomial functions examples with solutions; how to find the zeros of a polynomial function degree 3; finding zeros of a polynomial function calculator; how to find the zeros of a polynomial function degree 2
Answers
To find the roots of a polynomial of degree 3 we can use quadratic formula.
To find the roots of a polynomial function, also known as its zeros, you can use several methods. One method is to use the quadratic formula, which is a general formula that can be used to find the roots of a polynomial of degree 2 (quadratic).
If the polynomial is of degree 3 (cubic), you can use the cubic formula, which is a bit more complicated than the quadratic formula. The cubic formula is:
\(x = (-b + \sqrt{b^2 - 4ac)}/(2a) , (-b - \sqrt{b^2 - 4ac} )/(2a)\)
where a, b, and c are the coefficients of the polynomial in the form:
\(ax^3 + bx^2 + cx + d = 0\)
For example, if you have the polynomial \(x^3 - 7x^2 + 15x - 9 = 0\), then a=1, b=-7, c=15, and d=-9. Plugging these values into the cubic formula gives you:
\(x = (-(-7) + \sqrt{(-7)^2} - 4115))/(21) , (-(-7) - \sqrt{(-7)^2} - 4115))/(21)\)
which simplifies to:
\(x = (7 + \sqrt{(49 - 60)} /2 , (7 - \sqrt{(49 - 60} )/2\)
This gives you two solutions: x = 2 and x = -3.
If you don't want to use the cubic formula, you can also try factoring the polynomial into linear factors. For example, the polynomial \(x^3 - 7x^2 + 15x - 9\) can be factored as (x-1)(x-3)(x-3) = 0, which gives you the roots x=1, x=3, and x=3.
You can also use a graphing calculator or computer software to find the roots of a polynomial. Many of these tools will also give you the option to see the steps involved in finding the roots, which can be helpful for understanding the process.
Learn more about quadratic formula, here https://brainly.com/question/9300679
#SPJ4
A manufacturing plant has a 25 KVA single phase motor with a lagging power factor of 0.85
and this motor gets its power from a nearby a.c. voltage supply. A power factor correction
capacitor of 12 kVar is also connected p
Answers
In this case, the real power consumed by the motor is 21.25 kW.
How is this so?The real power (kW) consumed by the motor can be calculated using the formula:
P = S x pf
where P is the real power in kilowatts (kW), S is the apparent power in kilovolt-amperes (kVA), and pf is the power factor.
Given that the motor has a rating of 25 kVA and a power factor of 0.85 lagging, we have
P = 25 kVA x 0.85 = 21.25 kW
So we can say rightly that the real power consumed by the motor is 21.25 kW.
Learn more about Power:
https://brainly.com/question/29436001
#SPJ1
Full Question:
Although part of your question is missing, you might be referring to this full question:
A manufacturing plant has a 25 KVA single phase motor with a lagging power factor of 0.85 and this motor gets its power from a nearby a.c. voltage supply. A power factor correction capacitor of 12 kVar is also connected parallel to the motor.
Calculate the real power (kW) consumed by the motor (3)
If a pilot-operated check valve (POC) does not check flow, you will see a. erratic actuator movement b, no actuator movement c. external leakage d. fast actuator drift
Answers
If a pilot-operated check valve (POC) does not check flow, you will see a. erratic actuator movement.
What is a pilot-operated check valve (POC)?Pilot operated test valves paintings through permitting loose float from the inlet port via the opening port. Supplying a pilot strain to the pilot port permits float withinside the contrary direction. Air strain on pinnacle of the poppet meeting opens the seal permitting air to float freely.
An actuator fault is a form of failure affecting the machine inputs. Due to strange operation or fabric aging, actuator faults might also additionally arise withinside the machine. An actuator may be represented through additive and/or multiplicative fault.
Read more about the pilot-operated check valve:
https://brainly.com/question/13001928
#SPJ1
Three charges of 2 nC, -5 nC, and 0.2 nC are situated at P(2, 7/2,"/4), S(1, π, "/2), and Q(5, "/3,2/3), respectively. Find the force acting on the 2 nC charge at point P. Is this a force of attraction or repulsion?
Answers
Answer:htthrhtrhtrrtrth
Explanation:
trtrhtr
What is the key objective of data analysis
Answers
Answer: The process of data analysis uses analytical and logical reasoning to gain information from the data. The main purpose of data analysis is to find meaning in data so that the derived knowledge can be used to make informed decisions.
when you enter test -d tmp ; echo $?, you see a 0 displayed on the screen. what does this mean?
Answers
The 0 displayed on the screen after executing the command "test -d tmp ; echo $?" means that the test command was successful.
When you enter `test -d tmp; echo $?`, you see a "0" displayed on the screen. This means that the `test` command was successful or true. The `test` command, also known as `[` is a command-line utility used to verify or test file types, attributes, and so on.
For instance, it can test for file or directory presence, permissions, and so on. It exits with a status of 0 if the test is true, indicating success or truth, and with a status of 1 if the test is false, indicating failure or falsehood.
You can learn more about test dpm at
https://brainly.com/question/9759745
#SPJ11
Technician A says that the low level brake fluid switch on a master cylinder will turn on the brake warning light when the system is low on fluid. Technician B says that the low level switch also monitors the condition of the fluid and will activate the warning light when the brake fluid needs to be replaced. Who is correct?
Answers
Answer:
Technician A
Explanation:
The brake fluid switch or the brake switch is a sensor provided in the master cylinder monitors the brake fluid level in the vehicle. It is found inside the brake fluid reservoir. When the brake fluid level is too low, it warns the ABS by sending a signal. This device keeps us and the vehicle safe.
Thus in the context, technician A is correct.
Consider a regenerative gas-turbine power plant with two stages of compression and two stages of expansion. The overall pressure ratio of the cycle is 9. The air enters each stage of the compressor at 300 K and each stage of the turbine at 1200 K. Accounting for the variation of specific heats with temperature, determine the minimum mass flow rate of air needed to develop a net power output of 105 MW.
Answers
Answer: the minimum mass flow rate of air required to generate a power output of 105 MW is 238.2 kg/s
Explanation:
from the T-S diagram, we get the overall pressure ratio of the cycle is 9
Calculate the pressure ratio in each stage of compression and expansion. P1/P2 = P4/P3 = √9 = 3
P5/P6 = P7/P8 = √9 =3
get the properties of air from, "TABLE A-17 Ideal-gas properties of air", in the text book.
At temperature T1 =300K
Specific enthalpy of air h1 = 300.19 kJ/kg
Relative pressure pr1 = 1.3860
At temperature T5 = 1200 K
Specific enthalpy h5 = 1277.79 kJ/kg
Relative pressure pr5 = 238
Calculate the relative pressure at state 2
Pr2 = (P2/P1) Pr5
Pr2 =3 x 1.3860 = 4.158
get the two values of relative pressure between which the relative pressure at state 2 lies and take the corresponding values of specific enthalpy from, "TABLE A-17 Ideal-gas properties of air", in the text book.
Relative pressure pr = 4.153
The corresponding specific enthalpy h = 411.12 kJ/kg
Relative pressure pr = 4.522
The corresponding specific enthalpy h = 421.26 kJ/kg
Find the specific enthalpy of state 2 by the method of interpolation
(h2 - 411.12) / ( 421.26 - 411.12) =
(4.158 - 4.153) / (4.522 - 4.153 )
h2 - 411.12 = (421.26 - 411.12) ((4.158 - 4.153) / (4.522 - 4.153))
h2 - 411.12 = 0.137
h2 = 411.257kJ/kg
Calculate the relative pressure at state 6.
Pr6 = (P6/P5) Pr5
Pr6 = 1/3 x 238 = 79.33
Obtain the two values of relative pressure between which the relative pressure at state 6 lies and take the corresponding values of specific enthalpy from, "TABLE A-17 Ideal-gas properties of air", in the text book.
Relative pressure Pr = 75.29
The corresponding specific enthalpy h = 932.93 kJ/kg
Relative pressure pr = 82.05
The corresponding specific enthalpy h = 955.38 kJ/kg
Find the specific enthalpy of state 6 by the method of interpolation.
(h6 - 932.93) / ( 955.38 - 932.93) =
(79.33 - 75.29) / ( 82.05 - 75.29 )
(h6 - 932.93) = ( 955.38 - 932.93) ((79.33 - 75.29) / ( 82.05 - 75.29 )
h6 - 932.93 = 13.427
h6 = 946.357 kJ/kg
Calculate the total work input of the first and second stage compressors
(Wcomp)in = 2(h2 - h1 ) = 2( 411.257 - 300.19 )
= 222.134 kJ/kg
Calculate the total work output of the first and second stage turbines.
(Wturb)out = 2(h5 - h6) = 2( 1277.79 - 946.357 )
= 662.866 kJ/kg
Calculate the net work done
Wnet = (Wturb)out - (Wcomp)in
= 662.866 - 222.134
= 440.732 kJ/kg
Calculate the minimum mass flow rate of air required to generate a power output of 105 MW
W = m × Wnet
(105 x 10³) kW = m(440.732 kJ/kg)
m = (105 x 10³) / 440.732
m = 238.2 kg/s
therefore the minimum mass flow rate of air required to generate a power output of 105 MW is 238.2 kg/s
Please help I need by today !!
What is the purpose of an engineering notebook ?
What is the purpose of a portfolio?
Answers
Tech A says that air tools and equipment require a regular application of a lubricating oil to reduce wear and tear. Tech B says that some compressed air systems use an inline water trap that needs to be drained periodically. Who is correct?
Answers
Incomplete question. The options read;
A. Tech A
B. Tech B
C. Both A and B
D. Neither A nor B.
Answer:
C. Both A and B
Explanation:
Technician B is correct because the technician highlighted valid reasons why draining the compressed air systems is important.
For example, since this system helps to absorb moisture or oil from storage areas they thus need to be drained periodically in other to allow for more absorption space.
Also, the reasons mentioned by Technician A are of course correct because it is generally believed that the application of lubricants such as oil helps to reduce wear and tear.
To determine the expiration date of the last annual aircraft inspection, a person should refer to the
A- airworthiness certificate
B- registration certificate
C- aircraft maintenance records
Answers
To determine the expiration date of the last annual aircraft inspection, a person should refer to the aircraft maintenance records.
What are aircraft maintenance records?
Aircraft maintenance records include information about the work done to the aircraft, the date it was finished, the signature of the maintenance team, information about the FAA certificate, and the certificate number and signature of the person who put the aircraft back in service. The maintenance records mentioned in this rule can be simplified into two groups: permanent records and expiring records.
Permanent records are those maintenance logs that need to be retained and kept up-to-date for the aircraft forever. They act as a record of every maintenance action that has taken place during the lifecycle of the aircraft. It also functions as a tool for figuring out whether an aircraft has received all necessary maintenance and is in a state that allows for safe flight.
To learn more about aircraft maintenance records, use the link given
https://brainly.com/question/27961960
#SPJ4
True or false Self Driving Cars are examples of emerging technology
Answers
determine the optimum compressor pressure ratio specific thrust fuel comsumption 2.1 220k 1700k 42000 1.004
Answers
Answer:
hello your question is incomplete attached below is the complete question
A) optimum compressor ratio = 9.144
B) specific thrust = 2.155 N.s /kg
C) Thrust specific fuel consumption = 1670.4 kg/N.h
Explanation:
Given data :
Mo = 2.1 , To = 220k , Tt4 = 1700 k, hpr = 42000 kj/kg, Cp = 1.004 kj/ kg.k
γ = 1.4
attached below is the detailed solution
Asynchronous communications does not happen in real time.a. trueb. false
Answers
Answer:
true
Simply put, asynchronous communication is communication that doesn't happen in real-time (e.g. on the phone, in-person, or during a live video conferencing meeting). For instance, in the above example, your coworker is busy and can't properly comprehend the information you're providing when you visit her desk.
Which of the following terms describes the path from an electrical source to a switch or plug?
transmitter
circuit breaker
raceway
breaker panel
Answers
Answer:
transmitter hope thus helped!
Explanation:
Raceway is the answer
"A raceway is an enclosed conduit that forms a physical pathway for electrical wiring."
How many grains are on the surface of the head of a pin? assume that the head of a pin is spherical with a 1-mm diameter and has an astm grain size of 10
Answers
Answer:
Given, diameter of pin head d = 1 mm = 1/25.4 = 0.0394 in Surface area of a pinhead, A = 4pr^2 =
Explanation:
eesh
2. Solve for the unknown variable:
C = 16in
a =
b = 12in
Answers
Answer:
I don't Know what it is supposed to equal.
Explanation:
Tell me this, and consider it done
A 1.96 in. diameter rod must be machined on a lathe to a smaller diameter for use as a specimen in a tension test. The rod material is expected to break at a normal stress of 68,787 psi. If the tensile testing machine can apply no more than 797 lb of force to the specimen, calculate the maximum rod diameter that should be used for the specimen.
Answers
Answer:
Explanation:
The maximum normal stress that can be applied to the specimen is given by the ratio of applied force to the area of the cross section of the specimen:
stress = force / area
The area of the cross section of a rod is given by the formula for the area of a circle:
area = πr^2
where r is the radius of the rod. We are given the diameter of the rod, which is 1.96 inches, so the radius is half of that, or 0.98 inches.
The maximum normal stress that the specimen can withstand is 68,787 psi, and the maximum force that can be applied is 797 lb. Substituting these values into the equation for stress gives:
68,787 psi = 797 lb / πr^2
Solving for the radius r gives:
r = √(797 lb / (68,787 psi × π))
Substituting in the value for π and calculating gives:
r ≈ 0.330 inches
The maximum diameter of the rod is twice the radius, so the maximum diameter is:
d = 2r ≈ 0.660 inches
Therefore, the maximum rod diameter that should be used for the specimen is approximately 0.660 inches.
You need to terminate a Cat6 UTP cable with an RJ45 connector. Yourorganization's IT policy states that all cable connectors must be wired accordingto TIA568B standards.Drag the UTP wire on the left to the correct pin on the RJ45 connector on the right.Pin 1-White with orange stripePin 2-Solid orangePin 3-White with green stripePin 4-Solid bluePin 5-White with blue stripePin 6-Solid greenPin 7-White with brown stripePin 8-Solid brownThe T568B wiring standard specifies the following pinout for RJ45 connectors:Pin 1: White with orange stripePin 2: Solid orangePin 3: White with green stripePin 4: Solid bluePin 5: White with blue stripePin 6: Solid greenPin 7: White with brown stripePin 8: Solid brow
Answers
To terminate a Cat6 UTP cable with an RJ45 connector according to the TIA568B wiring standard, you would match the UTP wire colors to the corresponding pin on the RJ45 connector as follows:
Pin 1: White with orange stripe
Pin 2: Solid orange
Pin 3: White with green stripe
Pin 4: Solid blue
Pin 5: White with blue stripe
Pin 6: Solid green
Pin 7: White with brown stripe
Pin 8: Solid brown
So, the correct wiring for the RJ45 connector would be as follows:
Pin 1: White with orange stripe
Pin 2: Solid orange
Pin 3: White with green stripe
Pin 4: Solid blue
Pin 5: White with blue stripe
Pin 6: Solid green
Pin 7: White with brown stripe
Pin 8: Solid brown
Learn more about Cat6 UTP here
https://brainly.com/question/3179306
#SPJ11
what is called periodic function give example? Plot the output which is started with zero degree for one coil rotating in the uniform magnetic field and name it. How can you represent this output as the periodic function?
Answers
Answer:
A periodic function is a function that returns to its value over a certain period at regular intervals an example is the wave form of flux density (B) = sin wt
Explanation:
A periodic function is a function that returns to its value over a certain period at regular intervals an example is the wave form of flux density (B) = sin wt
attached to the answer is a free plot of the output starting with zero degree for one coil rotating in a uniform magnetic field
B ( wave flux density ) = Bm sinwt and w = 2\(\pi\)f = \(\frac{2\pi }{T}\) rad/sec
