It is presented either in deductive or inductive perspective

A 20 mA maximum output current. More than 2 K is the suggested output load. Input Ranges between 2 and 6 mV for offset.

The 741 is designed to operate between -5 and -15 Vdc, with a supply-voltage operating range of -4.5 volts (lowest) to -18 volts (maximum). Measures the amount of current an op-amp can generate or drain from an output pin. The common mode input swing should be within +/-12 volts for a 741 working at +/-15 volts. Regardless of the supply voltage, voltages over 15V have the potential to harm an op-amp.

For a certain historical value, the op-amp has a built-in short circuit protection. This amount is 25 mA for the 741 IC. Source current is the amount of current the op-amp draws from the power supply; the majority of op-amp statistics do not include this characteristic. The supply current is equal to 2.8 mA for the 741c op-amp.

To learn more about output current refer to :

https://brainly.com/question/15238377

#SPJ4

Answer:

Explanation: that’s the answer! 46kg

A stepped uniaxial bar is subjected to forces. The length and area of cross-sections of the two elements are asked to be written. The stiffness matrix of the given information is to be calculated.

Consider a stepped uniaxial bar subjected to forces as shown in the below diagram. The above bar has two different areas of cross-section and lengths. Hence, the bar can be divided into two elements with different areas and lengths.

Let us consider Element 1:

Here, \(l_1\) = Length of element 1

\(A_1\) = Area of cross-section of element 1

Let \(P_1\) and \(P_2\) be the forces applied on Element 1 and Element 2 respectively.

In general, the element stiffness matrix can be written as \(k = AE / Le\), where A is the area of the cross-section, E is the modulus of elasticity, and Le is the length of the element.

Let us calculate the stiffness matrix for Element 1. The stiffness matrix of Element 1, \(k_1\) is given by: 

\(k_1 = (A_1E_1 / l_1) * [1, -1; -1, 1]\)

Let us consider Element 2:

Here, \(l_2\) = Length of element 2

\(A_2\) = Area of cross-section of element 2

The stiffness matrix of Element 2, \(k_2\) is given by:

\(k_2 = (A_2E_2 / l_2) * [1, -1; -1, 1]\)

Now, we need to find the stiffness matrix of the complete bar. Let us consider k as the stiffness matrix of the complete bar. Then, \(k = [k_1 + k_2]\) is the stiffness matrix of the complete bar.

The complete stiffness matrix of the given problem is given by: \(k = [A_1E_1/l_1 + A_2E_2/l_2] * [1, -1; -1, 1]\)

Hence, the stiffness matrix of the given problem is given by \([A_1E_1/l_1 + A_2E_2/l_2] * [1, -1; -1, 1].\)

Learn more about stiffness matrix here:

https://brainly.com/question/30638369

#SPJ11

Answer:

I dont know the answer either

Explanation:

Answer:

flux

Explanation:

Answer:

Tires or wheels? I think this is the answer. ^_^

Explanation:

The classification of the working surfaces are as follows;

A working surface is a flat surface on which various activities can be carried out.

In a construction system, the duty carried on a particular working surface varies from another. They can be categorized into heavy-duty, medium-duty, light-duty, and very light-duty.

The classification of the working surfaces are as follows;

Learn more about the working surface here:

https://brainly.com/question/16508484

The mechanical properties of organic solids most relevant to deformable devices include the elastic modulus (usually obtained as the tensile or Young's modulus),(109) elastic range and yield point,(110) toughness,(111) and strain to fracture(31

The U.S. is heading toward its biggest political and constitutional crisis since the Civil War, and the collapse of federal authority, as well as the division of the country into enclaves of Republicans and Democrats is known to be a true statement.

In regards to political science, a constitutional crisis is known to be a kind of an issue or a problem or it can be called a conflict in the function of a government that is said to be the political constitution or other fundamental governing law which is seen or perceived to be unable to handle the countries issues.

Hence, The U.S. is heading toward its biggest political and constitutional crisis since the Civil War, and the collapse of federal authority, as well as the division of the country into enclaves of Republicans and Democrats is known to be a true statement.

Learn more about constitutional crisis  from

https://brainly.com/question/14320909

#SPJ1

Answer:

technician b?

Explanation:

2JZ/net 80 is the primary damage control cellphone circuit for damage control central


2JZ/net 80 is utilized by Pri DC & Stab Ctrl; DCC & all R/Ls damage manipulate imperative (DCC) is the hub of the deliver's harm control efforts. it's far organised to coordinate manipulate of all damage the deliver can also sufferin  warfare,  and  it  keeps  the  commanding  officer suggested of the capabilities of the deliver after every casualty.  It  trains  repair  events  to  perform  and control damage as independent devices.DCC employees take a look at all damage reviews and the corrective motion being taken. DCC issues direction when  repairs  are  now not  progressing  satisfactorily,damage is past the talents of the personnel worried, recommendation is asked, or corrective motion in progress is incorrect

To recognize extra about damage click right here
brainly.com/question/6562918
#SPJ4

Answer:

 Chemical engineering

Uses chemical processes to find new ways to produce goods. Making antibiotics, pesticides, safe clothes, and foods.

·         Civil engineering

Builds structures to try and make them efficient. Makes a tornado-proof house, explosion-proof bunker, or easily navigable subway system.

·         Electrical engineering

Develops the electrical components for things. Game systems, keyboards, projectors, or hard drives.  

·         Mechanical engineering

Mechanical engineers work with things with mechanical processes and moving parts. Drills, wheels, elevators, or cranes.  

·        

·    

·      

When the in-plane shear stress is maximum, the normal stresses on the respective planes are equal in magnitude and opposite in sign.

In materials subjected to pure shear stress, the stress state is characterized by two principal planes: one where the shear stress is maximum and another where the shear stress is minimum (zero). The normal stresses on these planes are responsible for the deformation and resistance to deformation in the material.

At the plane where the in-plane shear stress is maximum, the normal stresses are oriented along the principal directions. These normal stresses are equal in magnitude and have opposite signs. One normal stress is tensile (positive) while the other is compressive (negative). This distribution of normal stresses helps to maintain the equilibrium of forces and moments within the material.

Understanding this relationship between in-plane shear stress and normal stresses is crucial in analyzing the mechanical behavior of materials under complex loading conditions and in designing structures to withstand various types of stresses.

Learn more about shear stress here:

https://brainly.com/question/20630976

#SPJ11

The frequency  is 6.67 kHz and the duty cycle is:16.67%.

​Given:

Pulse width=25

Period=150

Frequency:

Frequency=1/(150×10^-6)

Frequency=1/0.00015

Frequency=6.666 kHz

Frequency=6.67 kHz (Approximately)

Duty cycle:

Duty cycle=(25×10^-6)/ (150×10^-6)×100%

Duty cycle=16.67%

Therefore the frequency  is 6.67 kHz and the duty cycle is:16.67%.

Learn more about Frequency and duty cycle here:https://brainly.com/question/16030651

#SPJ1

The pyramids are important to the study of engineering because they were some of the first structures built using engineering principles. The pyramids are an example of how engineering can be used to create amazing structures.

What is pyramid?

A pyramid is a structure with triangular exterior surfaces that converge to a single step at the summit, giving the shape the shape of a pyramid in the geometric sense. A pyramid's base can be trilateral, quadrilateral, or any polygon shape. A pyramid, as a result, has at least three exterior triangle surfaces. A typical variant is the square pyramid, which has a square base and four triangular exterior surfaces. The design of a pyramid, with the majority of the weight closer to the bottom and the pyramidion at the apex, means that less material will be pushed down from above. This weight distribution enabled early civilizations to build stable massive constructions.

To learn more about pyramid

https://brainly.com/question/218706

#SPJ13

Answer:

a

Explanation:

An eyewash station should be located within a maximum distance of 25 feet from every location where a person may come into contact with substances that can cause damage to their eyes.

Answer:

First off, employees must follow all OSHA safety and health standards AND all rules issued by their employers that are intended to comply with OSHA's health and safety standards and the OSH Act. Report all occupational injuries and illnesses. Report hazardous conditions. Cooperate during an OSHA inspection.

The statement that describes one of an employee's responsibilities under OSHA's rules is to report unsafe and unhealthful working conditions to appropriate officials. Thus, the correct option for this question is D.

Congress created OSHA to assure safe and healthful conditions for working men and women by setting and enforcing standards and providing training, outreach, education, and compliance assistance. Under OSHA law, employers are responsible for providing a safe and healthful workplace for their workers.

Employees shall use safety equipment, personal protective equipment, and other devices and procedures provided or directed by the agency and necessary for their protection. Employees shall have the right to report unsafe and unhealthful working conditions to appropriate officials.

At first, employees must have to follow all sorts of OSHA safety and health standards. All rules and regulations are issued by their employers that are intended to comply with OSHA's health and safety standards and the OSH Act.

Therefore, the correct option for this question is D.

To learn more about OSHA rules, refer to the link:

https://brainly.com/question/1264446

#SPJ2

A factor which is most significant in the lobbying efforts of the energy and natural resources industry include the following: C. Their economic resources allow them to support full-time professional lobbyists and staff researchers.

An interest group simply refers to a group that is composed of individuals who are primarily concerned with influencing various policies of the government based only on their interests, common aims, cause, goals, or people they represent.

In Sociology, a lobbyist can be defined as an activist whose endeavor and intent is to persuade government officials to enact laws (legislation) and policies that would significantly benefit their group at large.

This ultimately implies that, an energy and natural resources industry may seek to increase energy efficiency through lobbying for policy changes by investing more money and other economic resources in order to allow them support full-time professional lobbyists and staff researchers.

Read more on interest groups here: https://brainly.com/question/25656843

#SPJ1

Complete Question:

Which of the following factors is most significant in the lobbying efforts of the energy and natural resources industry?

a. Their focus on supporting social services makes them popular throughout the state.

b. Their alliance with several state environmental interests amplifies their voice.

c. Their economic resources allow them to support full-time professional lobbyists and staff researchers.

d. Their large member base motivates many members of the legislature to vote in their favor.

e. Their efforts to avoid electoral politics help them maintain a strong reputation.

i just need point to ask a question

Cut that photo by

1. Left click your mouse on the photo

2. Click cut

Then enter the file where you want to transfer and press

1. ctrl+v

Answer:

you can go to your file and then select the phpto and hold on a little bit and choose the delete option

Answer:

when car vroom it go electric

Explanation:

i think then it goes to some spinny thing that spins and make the electric and the electic spins the spinny thing and the smoke comes outside the back

/~\ The correct answer is:

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

B. A demand for unique features.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

I hope this helps! /~\

Answer:

A. A reliance on mass production of necessary parts.

Explanation:

Took the test

The size of the droplets is 0.58 x \(10^{-7\) cm and the interfacial tension of the droplets is 0.059 N/m.

The size and the interfacial tension of the droplets can be calculated as follows:

Droplet size:The specific area (a) of the droplets can be expressed as: a = (6/Vd) x (1/r)

where Vd is the volume of the droplet and r is the radius of the droplet. Solving for the volume of the droplet gives: Vd = (6/r) x (1/a)

The specific area (a) can be converted to surface area per unit mass (S) using the following equation: S = a x (1/d)where d is the density of the droplet, which is assumed to be equal to the density of water (1.0 g/cm³).

Therefore, S = a cm²/g.

Substituting the given values in the above equations, we get:

Vd = (6/4.25 x \(10^{5\) ) x (1/1.0 x \(10^{3\) ) = 1.41 x \(10^{-11\)  cm³S = 4.25 x \(10^{5\)  cm²/g

Radius of the droplet can be calculated as: r = (3Vd/4π)^(1/3) = (3 x 1.41 x 10^-11 / 4π)^(1/3) = 0.58 x \(10^{-7\)  cm

Interfacial tension: The solubility of the droplets (S) can be related to the interfacial tension (γ) by the following equation: S = (γVm) / (RT lnS)where Vm is the molar volume of the drug, R is the gas constant, and T is the temperature. Solving for the interfacial tension (γ) gives: γ = (S x RT lnS) / Vm

Substituting the given values in the above equation, we get:

γ = (11.5/100) x (8.314 x 298) x ln(11.5/100) / 22.3= 0.059 N/m

Therefore, the size of the droplets is 0.58 x \(10^{-7\) cm and the interfacial tension of the droplets is 0.059 N/m.

Learn more about tension :

https://brainly.com/question/30037765

#SPJ11

Jennifer's job of reviewing resumes to identify potential candidates for interviews suggests that she works in the Human Resources (HR) department or the Recruitment department of the company. These departments are responsible for screening and selecting candidates for job positions within the organization.

Jennifer's role of reviewing resumes and identifying potential candidates for interviews is typically associated with the Human Resources (HR) department or the Recruitment department of a company. Here's an explanation of why:

Human Resources (HR) Department: The HR department is responsible for managing the overall human capital of the organization. This includes tasks such as recruitment, selection, and hiring of employees. Reviewing resumes and identifying suitable candidates aligns with the HR department's responsibilities in sourcing and evaluating potential candidates for job positions.

Recruitment Department: Some larger organizations may have a dedicated Recruitment department. This department focuses specifically on the process of attracting, sourcing, and selecting candidates for job openings. Reviewing resumes is a crucial step in the recruitment process to assess the qualifications, skills, and experience of applicants.

In both cases, Jennifer's role involves carefully reviewing resumes to screen applicants and identify those who meet the desired qualifications and criteria set by the company. She plays a vital role in shortlisting candidates for further evaluation and potential interviews.

Learn more about resumes from

https://brainly.com/question/14218463

#SPJ11

Answer:

the answer for this question is true

Question:

It is always the employee's responsibility to make sure they wear their respirator. A) True B) False

Answer:

The answer to this question would be A. True

Explanation:

It would be the employee's responsibility the boss/manager should not have to tell them to put it on. If you don't know what a respirator is it's worn over the mouth and nose as a mask to prevent the inhalation of dust, and other chemicals and stuff.

I hope it helps you!

~XxBells is a cute girlxX~

#Learn with Brainly

Ice is generally a solid material, but under certain conditions, it can behave like a liquid and flow downhill. This phenomenon is known as glacial flow and is caused by a combination of factors. One of the main causes is pressure.

When large masses of ice accumulate on top of each other, the pressure on the lower layers increases, causing them to melt slightly and become more fluid-like. The weight of the ice also plays a role in this process. As gravity pulls the ice downhill, the weight of the ice mass creates a force that helps to push the ice forward. Additionally, the presence of water in the ice also contributes to its ability to flow like a liquid. As water molecules move around within the ice, they help to lubricate its movement, allowing it to flow more easily. In conclusion, the unique combination of pressure, weight, and the presence of water in ice allows it to behave like a liquid and flow downhill over time.

To know more about Solid visit:

https://brainly.com/question/28663047

#SPJ11

Answer:

uehgeg7djw7heidiisosowiuisiejei2k

As per the given data, Inertial velocity of point Q relative to point O:

I vQ/O = IωB × OQ = 0 [since IωB is zero]

a) Transformation tables between frames:

Frame B (Disk frame):

- Origin: Center of the disk

- xB-axis: Tangent to the circular path of the rolling disk

- yB-axis: Radial direction, pointing towards the center of the circle

- zB-axis: Perpendicular to the disk, pointing outwards

Frame I (Inertial frame):

- Origin: Fixed point O

- xI-axis: Tangent to the circular path of the rolling disk

- yI-axis: Radial direction, pointing towards the center of the circle

- zI-axis: Perpendicular to the plane of rotation, following the right-hand rule

b) Angular velocities and trigonometric functions:

ψ˙: Angular velocity of the disk about its center (frame B)

ψ˙ = 2π/τ  [since the disk completes one revolution in time τ]

˙θ: Angular velocity of the disk about the fixed point O (frame I)

˙θ = ψ˙ = 2π/τ

ϕ˙: Angular velocity of the disk relative to the fixed point O (frame I)

ϕ˙ = ˙θ - ψ˙ = 0 [since the disk rotates about O without slipping]

sin θ: Sin of the angle between the radial direction and the zI-axis

sin θ = r/R

cos θ: Cos of the angle between the radial direction and the zI-axis

cos θ = √(1 - (r/R)^2)

c) Angular velocity of B with respect to I:

IωB = ϕ˙ yI = 0

d) Angular acceleration of B with respect to I:

IαB = I d/dt (IωB) = 0 [since ϕ˙ is constant]

e) Inertial velocity of point Q relative to point O:

I vQ/O = IωB × OQ = 0 [since IωB is zero]

Thus, the B-frame unit vectors do not appear in the final answers since the disk is rolling without slipping, and the angular velocity and angular acceleration of the disk are both zero.

For more details regarding velocity, visit:

https://brainly.com/question/30559316

#SPJ1

The distance traveled by car A when they pass each other is 1071m

Given:

t=0

constant acceleration= 6 ft/s^2

speed= 80 ft/s^2

\(S_A= \frac{at1^2}{2} + V_At\\S_B= V_B (t1 +t)\)

= \(2 * (\frac{27}{2})^{2}/2 + 27 * 32.9\)

= 1071m

Read more about distance here:

https://brainly.com/question/2854969

#SPJ1