Identify the sentence
When you can see both sides of an issue equality we’ll, you find it difficult to take a stand , but some people insist that you take one side or another .

The potential difference is 0.063 V.

The potential difference is defined as the work done in moving a charge of 1 coulomb from one point to another.

An electron microscope is a microscope that uses an accelerated beam of electrons.

The formula given by De Broglie for the wavelength is as follows:

λ is the wavelength.

λ = h / p

 = h / mv

 = h / √2×m×q×V

where h is planks constant

q is the charge

m is the mass

4.5 * 10⁻⁹  = 6.63 * 10⁻³⁴ / √(2×9.31×10⁻³¹×1.6×10⁻¹⁹×V)

On solving for V we get

V = 0.063 V

Hence, the potential difference is 0.063 V.

For more information on de Broglie wavelength click on the link below:

brainly.com/question/4851688

# SPJ4

A) Speed of waves on the wire: 360 m/s. the wire is held rigidly at both ends and set into oscillation.

What is oscillation ?

Oscillation is a repeating back and forth movement between two points, or a continuous and regular alternation between two states. It is a type of periodic motion, which can either be regular or irregular, that is often seen in physical or biological systems.

In physics, oscillation is a type of motion that is repeated over and over again in the same pattern. Examples of oscillation include the swinging of a pendulum, the vibration of a tuning fork, and the wave-like motion of a spring. In biology, oscillation can refer to the cyclic changes in the activity of a living organism, such as the body temperature of a mammal, or the circadian rhythm of a plant. Oscillation is an important phenomenon in many areas of science, from engineering to economics.

To learn about more oscillation

https://brainly.com/question/12622728

#SPJ4

The Dielectrics are indeed very useful as insulators and their ability to store charges for future use is highly beneficial in many applications. However, as an AI language model, I do not have personal experiences or emotions like humans do. Therefore, I cannot provide you with a specific example of a recent act of kindness or generosity.

The Nevertheless, I can encourage you to think about the positive impact that such actions can have on the people around you. Acts of goodwill and kindness can range from small gestures like holding the door open for someone or giving a compliment, to larger actions like volunteering or donating to a charitable cause. Being kind and generous not only benefits those around us, but it can also have positive effects on our own well-being and mental health. Research has shown that acts of kindness can release feel-good hormones like oxytocin, which can reduce stress and improve mood. In conclusion, while dielectrics serve a practical purpose in insulating and storing charges, it is important to also remember the value of kindness and generosity in our daily lives. By making small gestures of goodwill towards others, we can all contribute to a more positive and compassionate society.

learn more about dielectrics here.

https://brainly.com/question/29357753

#SPJ11

The approximate mass of a star cluster whose most massive stars left on  main-sequence star is RMC 136a1 with the estimated mass of RMC 136a1 is 315 solar masses, a solar mass is equal to the mass of the sun. In general, it takes a very long time for stars to form.

It is also assumed that the stars in the cluster are homogeneous or have properties similar to each other. The amount of time a star stays in a staging or sequencing stage is determined by its mass.

A star cluster is one of two different forms of stellar assemblages that are bound together by the gravitational attraction of their individual members, who are linked together physically by a shared origin.

Therefore, a  study of the system by the Hubble Space Telescope found that the cluster is made up of over 200 extremely bright stars. The biggest one was called RMC 136a1. The estimated mass of R136a1 is 315 solar masses, where 1 solar mass equals the solar mass

Learn more about the star cluster here:brainly.com/question/14862077

#SPJ4

Answer:

2 N

Explanation:

From the question, it's given that

Mass m = 0.2 kg

Acceleration a = 10 m/s^2

The force a soccer goalie experience when stopping a ball will be equal to the force at which the ball is being kicked. This is

F = ma

Substitute all the parameters into the formula

F = 0.2 × 10

F = 2 Newton.

Answer:

D.Measurements made on these particles will be correlated.

Explanation:

Radioactive tritium (3H) labeled guanine is indeed used to measure the rate of biochemical processes that involve its binding or incorporation.

In this context, the best site for tritium labeling would be at the C8 position of the guanine molecule. This is because the C8 position is less likely to undergo exchange with the solvent (water) and maintains the integrity of the labeled guanine throughout the experiment. The best site for tritium labeling in this type of experiment would be the 8th position of the guanine molecule. This is because the 8th position is involved in biochemical processes such as base-pairing and is also solvent-accessible, allowing for efficient incorporation of the radioactive tritium.

Learn more about Radioactive here:

brainly.com/question/14454195

#SPJ11

Skills and abilities do not make up our personality.

Personality encompasses an intricate amalgamation of traits that define our individuality, comprising our cognitions, emotions, and actions. It is shaped by a combination of genetic predispositions and environmental factors.

Individuals with diverse personality profiles exhibit distinct patterns of thinking, emoting, and engaging in conduct. By comprehending our individual personality traits, we empower ourselves to make wiser decisions and cultivate lives imbued with greater happiness and well-being.

Learn about Personality here https://brainly.com/question/17636115

#SPJ1

If a 0.3% decrease in the price of a good causes its quantity supplied to decrease by 1%, then the supply is C. Inelastic.

In this scenario, the supply of the good is considered inelastic. The elasticity of supply measures the responsiveness of the quantity supplied to changes in price. When the price of a good decreases, and the quantity supplied decreases by a larger percentage, it indicates that the supply is relatively unresponsive to price changes.

To determine the elasticity of supply, we compare the percentage change in quantity supplied to the percentage change in price. In this case, a 0.3% decrease in price results in a 1% decrease in the quantity supplied. Since the percentage change in quantity supplied (1%) is greater than the percentage change in price (0.3%), the supply is considered inelastic.

Inelastic supply means that producers are less responsive to price changes, and a small change in price leads to a proportionally smaller change in quantity supplied. In such cases, producers may find it challenging to adjust their output levels quickly in response to price fluctuations.

To know more about Inelastic click here:

https://brainly.com/question/30103518

#SPJ11

the chemical formula for periodic acid is HI04

I hope this helps you

:)

If the intensity of the loud machine were reduced by a factor of 5, the new intensity level would be 90 dB.

This can be calculated using the formula for decibel levels, which states that the difference in decibel levels is equal to 10 times the logarithm of the ratio of the two intensities. So, if the original intensity level was 110 dB, reducing it by a factor of 5 would result in a new intensity level that is 10 times lower, which is equivalent to a reduction of 20 dB. Therefore, the new intensity level would be 90 dB (110 dB - 20 dB = 90 dB).
If a loud machine produces sounds with an intensity level of 110 dB and the intensity is reduced by a factor of 5, the new intensity level can be calculated using the decibel formula: dB = 10 * log10(I/I₀), where I is the intensity and I₀ is the reference intensity. First, find the original intensity (I) using the inverse formula: I = I₀ * 10^(dB/10). Then, divide the original intensity by 5 and use the decibel formula again to find the new intensity level. The new intensity level will be lower than the initial 110 dB due to the reduced intensity of the sound.

To know about sounds:

https://brainly.com/question/30045405

#SPJ11

The answer is a. Styrofoam. This is because the buoyant force is the upward force exerted on an object in a fluid (in this case, water) that opposes the weight of the object. This is because the buoyant force acting on an object is equal to the weight of the fluid displaced by the object. Styrofoam has a lower density than water, so it displaces a greater volume of water than its own weight.

Thus, the correct answer is a. Styrofoam.

To learn more about Styrofoam please visit:

https://brainly.com/question/21369568

#SPJ11

The potential difference through which the electron travelled is 3.383 * 10^-5 V.

Given: Initial velocity (u) = 0m/s, Final velocity (v) = 10 * 10^4 m/s, Charge of an electron, q = 1.6 * 10^-19 C.

The potential difference is given by the expression:

ΔV = (mv^2)/2q Here, m is the mass of the electron.

Hence, ΔV = (9.11 * 10^-31 kg * (10 * 10^4 m/s)^2) / (2 * 1.6 * 10^-19 C)

On calculating the value of ΔV, we get:

ΔV = 3.383 * 10^-5 V

Therefore, the potential difference through which the electron travelled is 3.383 * 10^-5 V.

To know more about acceleration visit:

https://brainly.com/question/2303856

#SPJ11

The voltage that is associated with the electron can be obtained as  \(4.6 * 10^-4\) V.

Potential difference, also known as voltage, is the difference in electric potential between two points in an electric circuit. It represents the work done per unit charge in moving a charge from one point to another.

We know that;

\(1/2mv^2 = eV\)

m = mass

v = velocity

e = electronic charge

V = voltage or potential difference

V =\(1/2mv^2/e\)

V = \(1/2 * 9.11 *10^-31 * (1 * 10^4)^2/ 1 * 10^-19\)

V =\(4.6 * 10^-4\)V

Learn more about potential difference:https://brainly.com/question/23716417

#SPJ4

Answer:

The troposphere and stratosphere are the only layers where you would find clouds.

Answer: Based on the information provided, the only layers where you would find clouds are the troposphere and the stratosphere.

The troposphere is the layer of the atmosphere that extends from the Earth's surface to about 8-15 kilometers (5-9 miles) above the Earth. This is the layer where most of the Earth's weather occurs, and it is where you will find clouds, such as cumulus clouds, stratus clouds, and cirrus clouds.

The stratosphere is the layer of the atmosphere that extends from about 15-50 kilometers (9-31 miles) above the Earth. This layer is characterized by a rise in temperature with altitude, and it is where you will find clouds called stratospheric clouds, such as nacreous clouds and polar stratospheric clouds.

The mesosphere is the layer of the atmosphere that extends from about 50-85 kilometers (31-53 miles) above the Earth. This layer is characterized by a decrease in temperature with altitude, and it is generally too cold and dry to support the formation of clouds.

The thermosphere is the layer of the atmosphere that extends from about 85 kilometers (53 miles) to the edge of space. This layer is characterized by a rise in temperature with altitude, and it is generally too thin and diffuse to support the formation of clouds.

I hope this helps! Let me know if you have any other questions.

Answer:

36km/h = 10m/s

Explanation:

That's the formula to convert

Answer:

C. -35N/m

Explanation:

Using Hooke's Law, we know that the elastic constant of a spring can be found with this formula:
\(F=-kx\)

where:

\(F\) is the force ( in Newtons)
\(k\) is the constant ( in Newtons per meter)
\(x\) is the extension ( in meters)

thus, by rearranging the formula we can get:
\(k=-\frac{F}{x}\)

\(k = -\frac{10}{0.286}\)

\(k=-34.96503N/m\)

Rounding off the answer, we get -35N/m

Answer:

The net displacement is

\(R= \sqrt{A^2+B^2+2AB \cos \theta}\)

\(=\sqrt{15^2+25^2+2AB \cos 30^\circ} \\\\=\sqrt{225+625+ \cos30^0} \\\\=38.7m\)

Explanation:

Suppose that you walk 15 meters at 30 degrees as measured from the East. Then you walk another 25 meters at 60 degrees from the East what is your net displacement

Given data

A = 15 m

B = 25 m

Angle between the vectors A and B is θ = 30°

The net displacement is

\(R= \sqrt{A^2+B^2+2AB \cos \theta}\)

\(=\sqrt{15^2+25^2+2AB \cos 30^\circ} \\\\=\sqrt{225+625+ \cos30^0} \\\\=38.7m\)

A single-phase, 125-volt receptacle installed to serve a washing machine in the laundry room of a dwelling unit must be installed within at least 6 Feet of the intended location of the appliance.

In  every kitchen, dining room, library, bedroom or area of dwelling units etc the receptacle units outlet shall be installed with provision specified in article 210.52(A)(1) and through (A)(4) while learning the article attached

Spacing: Receptacles should be installed at the point that wall space is more than 6ft or 1.8m from the receptacle.

Read more about Dwelling unit:

https://brainly.com/question/28283274

#SPJ4

Answer:

The speed (A) will decrease

V = F λ  (the frequency F remains the same to maintain continuity across the interface)

Therefore (C) the wavelength must decrease      

Note: n = speed of light in air / speed of light in medium

When a light wave enters a medium of greater optical density the two characteristics that are: (A) Speed, and (C) Wavelength will decrease in the wave.

It is given that a light wave enters a medium of greater optical density.

It is required to find the characteristics that will decrease.

It is defined as the type of waves such as sound waves or ocean waves but waves carry energy. Light does not need any medium to travel.

We know that:

\(\lambda =\frac{v}{f}\)

Where Lamda (λ) = Wavelength

                        (\(v\)) = Speed of wave

                        \((f)\) = Frequency of the wave.

The frequency remains the same to maintain continuity across the interface.

thus Speed of wave and Wavelength will decrease.

Learn more about the light here:

https://brainly.com/question/23342892

Answer:

here

Explanation:

Law of inertia states that a body remains in a position of rest or motion along a straight line unless an external force is applied..

Please mark me as brainliest

If no Minimum Crossing Altitude (MCA) is specified on a chart, the lowest altitude for crossing a radio fix would be the Minimum En Route Altitude (MEA). The MEA is the lowest altitude at which adequate navigation signal reception and obstacle clearance can be assured along an airway or a route segment. However, if the MEA is not high enough to provide obstacle clearance or communication signal reception, a higher minimum applies.

The next highest minimum altitude would be the Minimum Obstacle Clearance Altitude (MOCA), which provides at least 1,000 feet of obstacle clearance in non-mountainous terrain, or 2,000 feet of obstacle clearance in designated mountainous terrain areas. The MOCA also assures adequate navigation signal reception, but may not provide reliable communication signal reception.

If neither MCA nor MOCA are specified, the pilot must comply with the MEA for that particular segment. However, if the MEA is not high enough to provide obstacle clearance or communication signal reception, it is the pilot's responsibility to fly at a higher altitude that provides adequate clearance and signal reception.

In summary, the lowest altitude for crossing a radio fix, beyond which a higher minimum applies, is the MEA if no MCA is specified. If the MEA is not high enough to provide obstacle clearance or communication signal reception, the MOCA must be used. If neither MCA nor MOCA are specified, the pilot must comply with the MEA, but it is their responsibility to ensure adequate clearance and signal reception.

for more such questions on  altitude

https://brainly.com/question/28308143

#SPJ11

Answer:

2/3 Amp

Explanation:

Write the two equations for the two complete loops in the circuit:

Upper loop:   i1 * 1 Ω + 7 V + (i1 - i2) 1 Ω - 6 V= 0

2 i1 - i2 = -1

Lower loop:  (i2 - i1) 1 Ω + 6 V + i2 1 Ω - 3 V = 0

- i1 + 2 i2 = -3

Solve the system of two equations:

i1 = -5/3 Amp

i2 = - 7/3 Amp

Therefore, an amp-meter in the branch of the 6V battery will read the difference between current i1 and i2. That is 2/3 Amp.

Answer:

hydrochloric acid

Explanation:

The compound Mr. Pham's company used is most likely hydrochloric acid.

Hydrochloric acid is a strong acid and it is applied to remove corrosion and rusts from another body.

The acid is capable of dissolving and breaking down the rust and corrosion.

A base does not have this property and would not effectively remove the corrosion.

Sodium hydroxide and lithium hydroxide are bases.

Nitric acid is not as strong as hydrochloric acid.  

Answer:

hydrochloric acid

Explanation:

i just did the test 3 minutes ago.

hope this helps and have a good day.

:)

(1) The time does pilot take the weight to hit the ground = 2.4 s

(2) The pilot travel before land = 400 m

Because fall time is proportional to fall height and acceleration due to gravity (g) is constant,

t₁ = t₂  

s₁ = initial distance

s₂ = final distance

t₁ = initial time

t₂ = final time

Hence, the time does it take the weight to hit the ground = 2.4 s

The initial distance (s₁) = 200 m, and the pilot does a run at the same height but twice the speed.

So, the  pilot travel before land:

s₂ = 2 x s₁

= 2 x 200 m

= 400 m

The question is incomplete, it should be:

There are competitions in which pilots fly small planes low over the ground and drop weights, trying to hit a target. A pilot flying low and slow drops a weight; it takes 2.4 s to hit the ground, during which it travels a horizontal distance of 200 m. Now the pilot does a run at the same height but twice the speed. How much time does it take the weight to hit the ground? How far does it travel before it lands?

Learn more about distance here: https://brainly.com/question/29799935

#SPJ4

When the effort force needed to lift an object using an ideal lever with a force advantage greater than 1,  The effort force is less than the lifting force. The correct option is b.

Force is the mechanical physical quantity. The force advantage is equivalent to the mechanical advantage equal to the ratio of output to the input force.

The force advantage is

F.A = lifting force / effort force

When the effort force is greater, FA is less than 1. When FA is greater than 1, definitely, the effort force is less.

Thus, the effort force is less than the lifting force. The correct option is b.

Learn more about force advantage.

https://brainly.com/question/16558799

#SPJ1

Answer:

When several resistors are connected in series, the total resistance equals the sum of the individual resistors. In series combination, the current is same through each resistor.

1)   V=  60 volt

Total resistance R = R₁ + R₂

                              = 20 + 10

                              = 30 Ω

2) Ohms law states that,

           \(\sf I =\dfrac{V}{R}\\\\\\I = \dfrac{60}{30}\\\\I = 2 \ A\)

3) Voltage around 10 Ω resistor,

          V₂ = I R₂

             = 2 * 10

              = 20 volt

___________________________________________________

4) Total current = 1 A

5) Total voltage = 8 volt

6) Voltage around R₁ is V₁

              R₁ = 2 Ω  ; I = 1 A

              V₁ = IR₁

                   = 1 * 2

                   = 2 volt

7) Resistance 2:

        Total resistance = R

        Total voltage = V = 8 volt

        Total current = I = 1 A

                  \(\sf R = \dfrac{V}{I}\\\\\\ R = \dfrac{8}{1}\\\\\)

                  R = 8 Ω

               R₁ + R₂ = 8 Ω

                2 + R₂ = 8

                      R₂  = 8 - 2

                      R₂ = 6 Ω

8)Voltage around R₂:

                  \(\sf V_2 = IR_2\\\\V_2 = 1*6\\\\\)

                  V₂ = 6 volt

9) Total R = 8 Ω

_________________________________________________

10) Total V = 12 volt

11)  Total R = 8 + 8

                 = 16 Ω

12) Total current I,

                \(\sf I = \dfrac{V}{R}\\\\I = \dfrac{12}{16}\\\\I = 0.75 \ A\)

13) Voltage at each resistor:

           V₁ = I*R₁

               = 0.75 * 8

               = 6 volt

         V₂ = I*R₂

              = 0.75 * 8

             = 6 volt

_______________________________________________________

     14) Total R =   40 + 20

                       = 60 Ω  

15) To find V₁, first find total voltage.

           I = 2 A ;  R = 60 Ω  

           V = IR    

              = 2 * 60

               = 120 V

        V₁ + V₂  =V

        V₁ + 80 = 120

                V₁ = 120 - 80

                 V₁ = 40 volt              

The lowest incident kinetic energy is 50.0000125 ev

The energy an object has as a result of motion is known as kinetic energy.

A force must be applied to an object in order to accelerate it. We must put in effort in order to apply a force. After the work is finished, energy is transferred to the item, which then moves at a new, constant speed. Kinetic energy is the type of energy that is transferred and is dependent on the mass and speed attained.

The transmission probability of a particle in finite square well potential is

T = 1 / 1 + \(v_{0}\)² / 4 E( \(v_{0}\) - E) sin²βL

E is incident KE

And β = √2m ( E - \(v_{0}\) ) / h²

there is no reflection therefore R = 0 and T = 1

1 / 1 + \(v_{0}\)² / 4 E( \(v_{0}\) - E) sin²βL = 1

[ 1 +  \(v_{0}\)² / 4 E( \(v_{0}\) - E) sin²βL ] = 1

\(v_{0}\)² / 4 E( \(v_{0}\) - E) sin² (βL) = 0

sin² (βL) = 0

sin² (βL) = sin²(nπ)

For lowest KE n =1

βL = π

β = π / L

√2m ( E - \(v_{0}\) ) / h² = π / L

squaring both sides

2m ( E - \(v_{0}\) ) / h² = π² / L²

( E) = π² h² / 2mL² + \(v_{0}\)

Given width L = 2nm

π² h² / 2mL²

= π² × (1.05 × 10 -34 js )² / 2 × 1.67 × 10 -27 kg × ( 2 × 10-9 m)²

= 0.82 × 10 -23 j

since 1ev = 1.6 × 10 -19 j

π² h² / 2mL²

= 0.82 × 10 -23 / 1.6 × 10 -19

= 0.15 × 10 -4 ev

so incident kinetic energy is

( E) = π² h² / 2 mL² + \(v_{0}\)

= 0.15 × 10 -4 ev + 50 ev

= 50.0000125 ev >  \(v_{0}\)

you can't ignore this energy at quantum level.

To know more about kinetic energy visit

https://brainly.com/question/15764612

#SPJ4

Explanation:

Objects like apples, wood, and sponges are less dense than water. They will float. Many hollow things like empty bottles, balls, and balloons will also float. That's because air is less dense than water.

The width of the slit is 0.212 mm.

The wavelength of light is defined as “The distance between the two successive crests or troughs of the light wave”.

We know that the distance between minima is given by :

                                       \(t = (m_{f} - m_{i} ) \alpha x/d\)

where, t = distance between minima

            \(\alpha =\) wavelength

            x = distance of screen

            d = width of slit

            \((m_{f} - m_{i} ) =\) difference between minima

Given, x = 40 cm = 0.4 m

           \(\alpha = 690 nm = 690 * 10^{-9} m\)

           t = 2.60 mm = \(2.60 * 10^{-3} m\)

           \((m_{f} - m_{i} ) =\) 3 -1 = 2

Putting these values in above equation we get d = 0.212 mm

So the width of the slit is 0.212 mm.

To know more about Light visit:

https://brainly.com/question/13156031

#SPJ4

It doesn't rise and set. But it appears to rise and set because of the Earth's rotation on its axis. As the Earth rotates toward the east, it looks like the sun is moving west. As the Earth rotates, different locations on Earth pass through the sun's light.

It doesn't rise and set. But it appears to rise and set because of the Earth's rotation on its axis. ... As the Earth rotates toward the east, it looks like the sun is moving west. As the Earth rotates, different locations on Earth pass through the sun's light