b) Explain the rate of change of voltage of a thyristor in relation to reverse-biased (5 Marks) c) Draw and explain how a 3-phase fully controlled converter operates. (5 Marks)
Answers
The rate of change of voltage in a thyristor is directly related to its reverse-biased condition. When a thyristor is reverse-biased, it blocks the flow of current and acts as an open switch. In this state, the voltage across the thyristor increases gradually until it reaches the breakdown voltage, at which point the thyristor breaks down and allows a large current to flow. The rate of change of voltage during this breakdown process is typically steep and sudden.
A 3-phase fully controlled converter is a power electronics device used for controlling the flow of electric power in three-phase AC systems. It consists of six thyristors arranged in an H-bridge configuration. The converter operates by switching the thyristors in a specific sequence to control the direction and magnitude of current flowing through the load.
During operation, the converter first converts the incoming AC power into DC power using a rectifier circuit. The DC power is then fed to the H-bridge configuration of thyristors. By selectively triggering and turning off the thyristors, the converter can control the output voltage and current waveform. The triggering of the thyristors is synchronized with the input AC voltage, ensuring proper control and power transfer. This allows the converter to regulate the power flow, adjust the voltage and frequency, and provide efficient control of AC motors and other three-phase loads.
learn more about thyristor here:
https://brainly.com/question/30301010
#SPJ11
Related Questions
If water is so abundant on Earth, why are water resources such a big concern?
a. Water resources are not necessarily where humans need them and when they need them.
b. Humans are not very adept at exploiting water resources, so many go unused.
c. Most of the water on Earth is frozen in polar ice sheets.
d. Most of the water is caught up in the hydrologic cycle and is therefore not readily available.
Answers
The hydrologic cycle is important because it determines how water gets to ourselves, the plants, and the animals.
The hydrologic cycle is a very important process since it controls our planet's climate and ensures that all living things have access to water. We would run out of clean water, which is essential for life, if water didn't apparently recycle itself. aquatic environments are exposed to pathogens and silt. The continuous movement of water in the atmosphere, on the surface, and underneath the Earth is known as the hydrologic cycle (sometimes referred to as the water cycle). This cycle is the power exchange that affects the weather. Power is released and the environment is warmed when water condenses. The hydrological cycle of the earth's ecosystems is the culmination of all methods used to move water.
Learn more about The hydrologic cycle here:
https://brainly.com/question/30051098
#SPJ4
9. The highest voltage typically encountered on the job by a residential electrician is
volts.
A. 120
B. 600
C. 240
D. 480
Answers
Answer:
240
Explanation:
The highest voltage typically encountered on the job by a residential electrician is C. 240 volts.
What is voltage?Voltage is the measure of the difference in electrical power between two points in a circuit.
It is like the force that pushes electric charges in a circuit and is measured in volts (V) and affects how strong the electric current flows in a wire.
In many countries, the United States included, residential electrical systems often use a split-phase setup with a voltage of 120/240 volts.
This voltage is widely used for things like household appliances, lights, and other electrical needs in homes.
Learn more about electrical voltage at brainly.com/question/27861305
#SPJ2
3.18 LAB: Smallest and largest numbers in a list (PYTHON)
Write a program that reads a list of integers into a list as long as the integers are greater than zero, then outputs the smallest and largest integers in the list.
Ex: If the input is:
10
5
3
21
2
-6
the output is:
2 and 21
ANSWER IS INCORRECT:
lst=[]
n=int(input("Enter the size of the list : "))
for x in range(0,n):
temp=int(input()) ## taking the input of element of list from the user
lst.append(temp); ## adding element to list enter by the user
newList=[] ## this list keep that element until the negative element didnot come
for x in lst:
if(x<0):
break
else:
newList.append(x)
print(min(newList),end=" ") ## getting max element from the new list
print("and",end=" ")
print(max(newList)) ## getting min element from the new listlist
Answers
The given program reads a list of integers from the user until a negative integer is entered.
It then creates a new list with all the non-negative integers from the input list and outputs the smallest and largest integers from this new list. The program correctly uses the "append" method to add each input element to the list and the "min" and "max" functions to find the smallest and largest elements in the list.
However, it does not output the values in the correct format as the question asks for both the smallest and largest numbers to be output together. To fix this, we can modify the last three lines of the program as follows:
print(str(min(newList)) + " and " + str(max(newList)))
This will output the smallest and largest elements in the format "smallest_number and largest_number".
Learn more about integers here:
https://brainly.com/question/1768254
#SPJ11
Steam at 75 kPa and 8 percent quality is contained in a spring-loaded piston–cylinder device, as shown in Figure, with an initial volume of 2 m3 . Steam is now heated until its volume is 5 m3 and its pressure is 225 kPa. Determine the heat transferred to and the work produced by the steam during this process.
Answers
The heat transferred to and the work produced by the steam during this process is 13781.618 kJ/kg
How to calcultae the heat?
The Net Change in Enthalpy will be:
= m ( h2 - h1 ) = 11.216 ( 1755.405 - 566.78 ) = 13331.618 kJ/kg
Work Done (Area Under PV curve) = 1/2 x (P1 + P2) x ( V1 - V2)
= 1/2 x ( 75 + 225) x (5 - 2)
W = 450 KJ
From the First Law of Thermodynamics, Q = U + W
So, Heat Transfer = Change in Internal Energy + Work Done
= 13331.618 + 450
Q = 13781.618 kJ/kg
Learn more about heat on:
https://brainly.com/question/13439286
#SP1
Transcribed image text: Suppose that you want to arrange a meeting with two other people at a secret location in Manhattan that is an intersection of two streets (let's say 110th street and 2nd avenue, for concreteness). You want to send each of them a message such that they can find the location if they work together, but neither one can find it on their own. What could you send to each of them? Explain your reasoning.
Answers
Answer:
You could send each person one half of the coordinates of the secret location, such as "110th street" to one person and "2nd avenue" to the other person. This way, they would need to work together to share their information and determine the exact location of the intersection.
This approach ensures that neither person can find the location on their own, as they only have half of the information needed to determine the intersection. Additionally, sharing the coordinates separately adds an extra layer of security to the meeting location as it would be difficult for anyone to determine the meeting location without both pieces of information.
However, it's important to ensure that each person understands the instructions clearly, so they know to work together to determine the secret location. It's also important to choose a location that is not well-known, so the possibility of someone stumbling upon the meeting location by chance is reduced.
Explanation:
Which of the following power tools has a revolving vertical shaft and a cutter? *
1 point
a) saber saw
b) router
c) miter saw
d) circular saw
Answers
The tool that has a revolving vertical shaft and a cutter is a router. The correct option is b.
What are power tools?There are many different kinds of power tools, including portable power tools like a circular saw, heat guns, and wall chasers as well as electrical power tools like impact wrenches, lathes, power drills, power ratchet sets, and power saws.
Power tools including circular saws, jigsaws, drills, hammer drills, sanders, grinders, routers, and many others reduce labor and time requirements. The requirement for knowledge of the risks that power tools provide if used improperly is raised due to their rising use.
A power tool called a router has a flat base and a spinning blade that protrudes beyond the base. An electric motor or a pneumatic motor can drive the spindle.
Therefore, the correct option is b) router.
To learn more about power tools, refer to the link:
https://brainly.com/question/30115428
#SPJ6
In 2009 an explosive eruption covered the island of Hunga Ha'apai in black volcanic ash. What type of succession is this?
Answers
Answer:
The type of succession is:
Primary succession
Explanation:
This is a type of succession that occurs after a volcanic eruption or earthquake; it involves the breakdown of rocks by lichens to create new, nutrient rich soils.
Primary succession is one of the two types of succession we have. It begins on rock formations, such as volcanoes or mountains, or in a place with no organisms or soil.
For these problems, assume air behaves as an ideal gas with R = 0.287 k J k g K. A compressor operates at steady state and takes in air from ambient 0 kPa, gage and 300 K. The outlet pressure is 50 kPa, gage and 400 K. Determine: the mass flow rate if the inlet area is 10 cm2 and the inlet pressure is -2 kPa, gage. the minimum outlet temperature that is possible for this compressor. the isentropic efficiency of the compressor, assuming no heat loss. if there is a heat loss of 30 kJ/kg, the work required to run the compressor, and the new isentropic efficiency. A turbine receives air at 50 kPa, gage and 800 K. It discharges to 0 kPa, gage, and the outlet temperature is measured as 500 K. The mass flow rate is the same as in the previous problem. Determine: the maximum work the turbine can do under these conditions. the heat loss, if the turbine works isentropically.
Answers
Answer:
Part 1
1) 0.252 kg/s
2) 457.06 K
3) 63.45%
4) 17.96 kJ
5) 44.85%
Part 2
1) 65.92 kJ
2) 57.62 kJ/kg
Explanation:
1) The mass flow rate
The flow velocity is given by the Bernoulli relation;
\(U =\sqrt{ \dfrac{\Delta P}{\rho } }\)
Where:
ΔP = The difference in pressure = 50 - (-2) = 52 kPa
ρ = Density of air = 1.225 kg/m³
\(U =\sqrt{ \dfrac{52,000}{1.225 } } = 206.03 m/s\)
The volume flow rate, V = U × A
Where:
A = Cross sectional area of the of the inlet = 10 cm² = 0.001 m²
Therefore, V = 0.001 × 206.03 = 0.206 m³/s
The mass flow rate = ρ × V = 1.225 × 0.206 = 0.252 kg/s
2) The minimum outlet temperature
P₁v₁/T₁ = P₂v₂/T₂
v₁ = v₂
∴ P₁/T₁ = P₂/T₂
T₂ = P₂T₁/P₁ = 151.325*300/99.325 = 457.06 K
3) The isentropic efficiency no heat loss
h₁ = 300.4 kJ/kg
\(h_{(out \ actual)}\) = 401.3 kJ/kg
\(h_{(out \ isentropic)}\) = 441.9 + (457.06 - 440)/(460 - 440)*(462.3 - 441.9) = 459.30 kJ/kg
The isentropic efficiency, \(\eta _{S}\), is given by the expression;
\(\eta _{S} = \dfrac{h_{in} - h_{(out \ actual)}}{h_{in} -h_{(out \ isentropic)} } = \dfrac{300.4 - 401.3}{300.4 - 459.3} = 0.6345\)
Therefore, the isentropic efficiency, \(\eta _{S}\) in percentage = 63.45%
4) Where there is an heat loss of 30 kJ/kg, we have;
\(h_{(out \ actual \ new)}\) = \(h_{(out \ actual)}\) - Heat loss = 401.3- 30 = 371.3 kJ/kg
The work done = (371.3 - 300.04)*0.252= 17.96 kJ/s
The new isentropic efficiency is given by the relation;
\(\eta _{S, new} =\dfrac{300.4 - 371.3}{300.4 - 459.3} = 0.4485\)
Therefore, the isentropic efficiency, \(\eta _{S, new}\), in percentage = 44.85%
Part 2
1) Turbine mass flow rate = 0.252 kg/s
From
T₂ = P₂T₁/P₁ = 101.325*800/151.325= 535.67 K
h₁ = 822.2 kJ/kg
\(h_{(out \ actual)}\) = 503.3 kJ/kg
\(h_{(out \ isentropic)}\) = 544.7 + (535.67 - 520)/(540 - 520)*(544.7 - 524.0) = 560.92 kJ/kg
The maximum work, \(W_{max}\), is given by the expression;
\(W_{max}\) = Mass flow rate×(h₁ - \(h_{(out \ actual)}\))
\(W_{max}\) = (822 - 503.3)*0.252 = 65.92 kJ/s
2) The heat lost, \(h_{loss}\), is given by the relation;
\(h_{loss}\) = \(h_{(out \ isentropic)}\) - \(h_{(out \ actual)}\) = 560.92 - 503.3 = 57.62 kJ/kg.
The largest class of errors in software engineering can be attributed to _______.
Answers
Answer:
improper imput validation
Explanation:
Which of the following is an example of a tax
Answers
Answer:
A tax is a monetary payment without the right to individual consideration, which a public law imposes on all taxable persons - including both natural and legal persons - in order to generate income. This means that taxes are public-law levies that everyone must pay to cover general financial needs who meet the criteria of tax liability, whereby the generation of income should at least be an auxiliary purpose. Taxes are usually the main source of income of a modern state. Due to the financial implications for all citizens and the complex tax legislation, taxes and other charges are an ongoing political and social issue.
I dont know I asked this to
Explanation:
. Which of the following is a type of disc brake pad wear indicator?A. Scratcher typeB. Sensor typeC. Both A and BD. None of the above
Answers
the scratcher type is not a valid option. Therefore, the correct answer is B. Sensor type.
Disc brake pads have wear indicators that alert drivers when the pads need to be replaced. Among the options given, the sensor type is a type of disc brake pad wear indicator. These sensors are attached to the brake pads and are designed to make contact with the brake rotor when the pads wear down to a certain level. This contact triggers a warning light on the vehicle's dashboard, indicating that it's time to replace the brake pads. The scratcher type mentioned in option A is not a commonly used term for disc brake pad wear indicators, and option C is incorrect as the scratcher type is not a valid option. Therefore, the correct answer is B. Sensor type.
learn more about Sensor type here:
https://brainly.com/question/32129241
#SPJ11
HURRY I HAVE 10 MINUTES LEFT !!!!!
Select the subject areas a graphic designer might study as part of a graphic design program.
film studies
programming languages
computerized design
web site design
computer science
printing techniques
animation
Answers
Answer:
computer design and website design
The answer is:
computer design and website design(at least those two maybe)
Find the general solution of the given differential equation. Give the largest interval over which the general solution is defined. Determine whether there are any transient terms in the general solution.
x dx/dy−y=x^2sinx
Answers
Answer:
Interval: x∈ ( 0, ∞ )
There are no transient terms
Explanation:
x (dy/dx) – y= x^2sinx
Attached below is the detailed solution of the Given problem
There are no transient terms found in the general solution
Interval: x∈ ( 0, ∞ )
A trucking company owns two types of trucks. Type \( A \) has 40 cubic metres of retrigerated space and 10 cublio metres of non-retrigerated space. Type B has 10 cubic metres of retrigerated space and
Answers
The trucking company owns two types of trucks: Type A and Type B. In summary, Type A trucks have both refrigerated and non-refrigerated space, while Type B trucks only have refrigerated space.
Type A trucks have 40 cubic meters of refrigerated space and 10 cubic meters of non-refrigerated space. This means that these trucks can transport perishable goods that require temperature control in the refrigerated space, while also having additional space for non-perishable items that do not require refrigeration.
Type B trucks have 10 cubic meters of refrigerated space. These trucks are designed specifically for transporting perishable goods that require temperature control. For instance, they can be used to transport frozen foods, dairy products, or any other goods that need to be kept at a specific temperature to prevent spoilage.
To know more about trucking company visit:
brainly.com/question/9171028
#SPJ11
what do you think the author is trying to express to society during his time of period through this story? in the open window
Answers
The City of Palo Alto wants to keep the foothills on the western edge of the city as green open space, but doesn't have the money to buy up the affected property, so instead it adopts a zoning ordinance that prohibits development or making any use whatsoever of property within a zone whose boundaries are the lower foothills at the edge and just beyond the line of existing developed properties nearest to the foothills. A property owner in the rezoned area will probably succeed in challenging the zoning restriction as a government "taking" of land without compensation.
True or False
Answers
The statement "A property owner in the rezoned area will probably succeed in challenging the zoning restriction as a government "taking" of land without compensation" is true because the zoning ordinance that prohibits any development or use of property within a specific zone can potentially be seen as a government "taking" of land without compensation.
The Fifth Amendment of the United States Constitution prohibits the government from taking private property for public use without just compensation.
In this case, the property owners in the rezoned area can argue that the zoning restriction effectively deprives them of the economic value and use of their land without providing fair compensation. Therefore, they have a reasonable chance of succeeding in challenging the zoning ordinance as a violation of their constitutional rights.
Learn more about property owner https://brainly.com/question/28315374
#SPJ11
See Attached PNG Below.
Answers
The Cartesian and polar notation based on the information is solved below.
How to solve the notationCartesian notation:
P₁ - P₂ = (6cos(445°) - 2cos(460°))i + (6sin(445°) - 2sin(460°))j
≈ 3.43i - 2.91j
P₂ - P₁ = (-3.43)i + (2.91)j
Polar notation:
R1 = sqrt((6^2 + 2^2) - (262cos(460°-445°))))
≈ 3.91"
θ1 = atan2(6sin(445°) - 2sin(460°), 6cos(445°) - 2*cos(460°))
≈ -20.94°
R2 = sqrt((6^2 + 2^2) - (262cos(445°-460°))))
≈ 3.91"
θ2 = atan2(2sin(460°) - 6sin(445°), 2cos(460°) - 6*cos(445°))
≈ 159.06°
b) Cartesian notation:
P₁ - P₂ = (10cos(120°) - 4cos(40°))i + (10sin(120°) - 4sin(40°))j
≈ -5.74i + 8.66j
P₂ - P₁ = (5.74)i - (8.66)j
Polar notation:
R1 = sqrt((10^2 + 4^2) - (2104cos(40°-120°))))
≈ 11.18 cm
θ1 = atan2(10sin(120°) - 4sin(40°), 10cos(120°) - 4*cos(40°))
≈ 123.69°
R2 = sqrt((10^2 + 4^2) - (2104cos(120°-40°))))
≈ 11.18 cm
θ2 = atan2(4sin(40°) - 10sin(120°), 4cos(40°) - 10*cos(120°))
≈ -56.31°
c) Cartesian notation:
P₁ - P₂ = (4cos(4225°) - 3cos(45°))i + (4sin(4225°) - 3sin(45°))j
≈ -2.58i - 0.17j
P₂ - P₁ = (2.58)i + (0.17)j
Polar notation:
R1 = ✓(4^2 + 3^2) - (243cos(45°-4225°))))
≈ 4.14'
θ1 = atan2(4sin(4225°) - 3sin(45°), 4cos(4225°) - 3*cos(45°))
≈ -44
Learn more about Cartesian on
https://brainly.com/question/4726772
#SPJ1
which of the following is the most complete summary of the selective incorporation doctrine
Answers
The selective incorporation doctrine is a legal principle that applies certain provisions of the Bill of Rights to the states through the Due Process Clause of the Fourteenth Amendment, ensuring that fundamental rights are protected at both the federal and state levels.
The selective incorporation doctrine is rooted in the idea that certain fundamental rights guaranteed by the Bill of Rights should apply to the states, not just the federal government. Prior to the doctrine's development, the Bill of Rights only applied directly to the federal government. Through the Due Process Clause of the Fourteenth Amendment, the Supreme Court has selectively incorporated specific provisions of the Bill of Rights to apply to the states, thereby protecting individuals' fundamental rights from state infringement. This means that state governments must also uphold rights such as freedom of speech, religion, and the right to a fair trial, as outlined in the incorporated provisions. The selective incorporation doctrine has played a significant role in shaping the balance of power between the federal government and the states and in safeguarding individual rights across the United States.
Learn more about incorporation doctrine here;
https://brainly.com/question/29549433
#SPJ11
Compare automation and autonomous
Answers
Answer:
Automation generally means “a process performed without human assistance”, while autonomy implies “satisfactory performance under significant uncertainties in the environment and the ability to compensate for system failures without external intervention [emphasis mine].”
Explanation:
What is your creative solution for clean, sustainable, and accessible energy?
Answers
Refrigerant 134a is the working fluid in a vapor-compression heat pump system with a heating capacity of 70,000 Btu/h. The condenser operates at 180 lbf/in2, and the evaporator temperature is 20˚F. The refrigerant is a saturated vapor at the evaporator exit and exits the condenser at 120˚F. Pressure drops in the flows through the evaporator and compressor are negligible. The compression process is adiabatic, and the temperature at the compressor exit is 200˚F. Determine
a) The mass flow rate of refrigerant, in lb/min
b) The compressor power output, in horsepower.
c) The isentropic compressor efficiency.
d) The coefficient of performance.
Answers
For binary flash distillation, we discussed in class that there are 8 variables (F, ZA, V, ya, L, XA, P and T) and 4 equations derived from VLE and mass balances. Thus, we typically require 4 of these variables to be given so that we can obtain a unique solution to the problem. Let's say, your manager tells you that he has a feed mixture with 2 components (given F, za) and he requires you to come up with a flash column that can produce a certain desired amount of Vapor product (thus V, ya are specified). Identity of both components is known and all VLE data has been provided to you. Has the manager given you enough data? If yes, give a step-by-step description of how would you go about designing the flash column (basically find P and T)? If no, why?
Answers
Answer:
yes
Explanation:
ooooooooooooooooooooooooooooooo
The injection molding department of a company that operates 24x7 uses an average of 34 gallons of special lubricant per day. The usage of lubricant is normally distributed with a standard deviation of 4.4 gallons per day and it takes 6.5 weeks for an order of lubricant to be delivered. If the largest service level is 73%, what is the reorder point?
Answers
The injection molding department of a company that operates 24x7 uses an average of 34 gallons of special lubricant per day. The usage of lubricant is normally distributed with a standard deviation of 4.4 gallons per day and it takes 6.5 weeks for an order of lubricant to be delivered. If the largest service level is 73% The reorder point for the injection molding department is approximately 1549.508 gallons.
To calculate the reorder point, we need to consider the lead time demand, which is the demand during the time it takes for a new order to be delivered.
Given that the injection molding department operates 24x7 and uses an average of 34 gallons of special lubricant per day, we can calculate the daily demand as 34 gallons.
Since the demand follows a normal distribution with a standard deviation of 4.4 gallons per day, we can use the Z-score formula to calculate the safety stock. The Z-score represents the number of standard deviations from the mean.
To determine the Z-score corresponding to a service level of 73%, we can use a Z-table or a statistical calculator. The Z-score for a 73% service level is approximately 0.57.
Next, we need to calculate the lead time demand. The lead time is given as 6.5 weeks, and since there are 7 days in a week, the lead time is equal to 6.5 x 7 = 45.5 days.
To calculate the lead time demand, we multiply the average daily demand by the lead time in days. Therefore, the lead time demand is 34 gallons/day x 45.5 days = 1547 gallons.
To calculate the reorder point, we add the lead time demand to the safety stock. The safety stock is given by the formula: Safety Stock = Z-score x standard deviation.
Using the given standard deviation of 4.4 gallons per day and the calculated Z-score of 0.57, the safety stock is 0.57 x 4.4 gallons/day = 2.508 gallons.
Finally, we can calculate the reorder point by adding the lead time demand to the safety stock: Reorder Point = Lead time demand + Safety stock.
Reorder Point = 1547 gallons + 2.508 gallons = 1549.508 gallons.
Learn more about injection molding here :-
https://brainly.com/question/33176905
#SPJ11
Jenifer wants to add some more hardware to her computer system. if she is adding a video card and a sound card, what must she use on the motherboard to connect these extras?
Answers
The sound card, video card can be usually conned to the motherboard with a PCI or PCIe card slot.
What is a Sound card?A sound card is a part of a computer that converts analogue audio signals to digital ones and digital ones to digital ones. Technically speaking, a sound card is an optional component, but it's essential if you wish to connect an analogue microphone or listen to your PC's audio through wired headphones or speakers (much like an external DAC).
These components are made to handle it; the CPU of the computer is not intended for the specific task of processing signals into high-quality sound.
Usually, to connect them, a PCI or PCIe card slot on the motherboard is utilized. By utilizing these connections, the card can interface with all the power and other contacts to connect to the motherboard; all you need to do is slide the card into the slot and tighten the backplate with a screw.
For more information about Sound Card :
https://brainly.com/question/21852133
#SPJ1
a diode for which the forward voltage drop is 0.7 v at 1.0maisoperatedat0.6v.whatisthevalueofthecurrent?
Answers
The current in this diode is 0.6 mA because the forward voltage drop of the diode is 0.7 V at 1.0 mA. When the voltage is decreased to 0.6 V, the current is also decreased to 0.6 mA.
A diode is an electronic component that allows current to flow in one direction only. It is made up of two terminals, an anode and a cathode, and is typically made of a semiconductor material such as silicon. Diodes are used in a variety of applications, such as rectifying AC to DC, providing voltage regulation, and protecting circuits from overvoltage. Diodes are also used in logic circuits, such as AND and OR gates, to control the flow of current. Diodes are typically made of a semiconductor material such as silicon. They are made up of two terminals, an anode and a cathode, and are designed to allow current to flow in one direction only. Diodes are used in a variety of applications, such as rectifying AC to DC, providing voltage regulation, and protecting circuits from overvoltage. Diodes are also used in logic circuits, such as AND and OR gates, to control the flow of current. Diodes can also be used to convert AC to DC, as well as to amplify signals. Diodes are also used in a variety of other applications, such as in light-emitting diodes (LEDs) and in photodiodes.
Learn more about Diodes here
https://brainly.com/question/12721595
#SPJ4
What are some of the trade-offs of a move to an enterprise-level analytics solution for individual end users who might have grown accustomed to working with their own customized solutions for generating data?
Answers
Answer:
THE thing is 435
Explanation:
Some of the trade-offs that must be made while transitioning from an individually tailored solution to such an enterprise-level solution are about as continues to follow.
Enterprise-level analytics Different individuals must be given some amount of control over their data in corporate-level systems.To counteract opposition from individuals who seem to be comfortable working utilizing customized statistics, training needs to be provided so that they can utilize cutting-edge large enterprise technologies.Adequate orientation training, as well as perks, should have been provided so that employees may become acquainted using the changing approach.
As a result, the aforementioned response seems to be correct.
Find out more information about enterprise-level analytics here:
https://brainly.com/question/25071524
true or false: in the event of accelerator failure, do not turn off the engine, as you will lose braking and steering control.
Answers
False. In the event of accelerator failure, it is generally recommended to turn off the engine as a safety precaution.
While it is true that turning off the engine will result in the loss of power steering and power-assisted braking, it is still the safer course of action compared to allowing the vehicle to continue accelerating uncontrollably.
When the accelerator pedal becomes stuck or unresponsive, it can lead to a potentially dangerous situation where the vehicle speeds up rapidly, increasing the risk of accidents. By turning off the engine, the primary source of power to the wheels is eliminated, causing the vehicle to slow down gradually.
Although power steering and power-assisted braking will be lost, it is still possible to steer the vehicle and apply the brakes manually. While the effort required to steer and brake will be significantly increased, it is a safer option than continuing with an uncontrolled acceleration.
Once the engine is turned off, the driver should engage the hazard lights to indicate to other drivers that there is an issue with the vehicle. They should then carefully maneuver the vehicle to a safe location off the road, using the remaining steering and braking capability.
It is important for drivers to familiarize themselves with the correct procedures for handling emergency situations, including accelerator failure, to ensure their safety and the safety of others on the road. It is recommended to consult the vehicle's owner's manual or seek guidance from local authorities for specific instructions related to the vehicle being operated.
Learn more about power-assisted braking here:
https://brainly.com/question/13279330
#SPJ11
What project is this ?
Answers
Answer:
a building project...
Explanation:
The part of a circuit that carries the flow of electrons is referred to as the?
Conductor
Electrostatic Field
Dieletric
Insulator
Answers
Answer:
Conductor
Explanation:
Current is carried by a conductor.
__
The purpose of a dielectric and/or insulator is to prevent current flow. An electrostatic field may set up the conditions for current flow, but it carries no current itself.
2. Data Compression (50 points): Write a MIPS assembly program in the MARS simulator that accepts an input string of size less than 50 characters, and applies the following compression algorithm to the string, and then prints the resulting compressed string. The input string will only consist of alphabets, i.e., a-z and A-Z. First check the string to make sure it's a valid input (if not, print an error message and quit). Then walk through the string looking for consecutive occurrences of the same character and replace them with the character and a count (called a "run length encoding"). For example, if you see AAAAA, you would replace them with A5. If you see BBBBBBBBBBBB, you would replace them with B12. Single character occurrences do not need a count. At the end, print the compression ratio, which is a floating point number = (size of input string) / (size of output string). For reference, here is an Here is an example run of the program: Provide an input string with less than 50 characters and only containing a-z or A-Z: AACCCCCGTTTTTTTTTTTTTTAAAbbcd The compressed string is: A2C5GT14A3ab2cd The compression ratio is
Answers
The compression ratio is 8.0 #message for printing compression ratio
.text #text segment ;main:#print prompt,li $v0, 4,la $a0, prompt,syscall
What is ratio?Ratio is a comparison between two or more quantities expressed in terms of their relative sizes. Ratios are typically written using the following format: a:b, where a and b are two numbers or quantities. Ratios can be used to compare measurements of different units, such as time, distance, weight, speed, or money. Ratios can also be used to compare more abstract quantities, such as levels of satisfaction, happiness, or importance. Ratios can be used to create fractions, which can then be used to solve many math problems.
To learn more about ratio
https://brainly.com/question/30683918
#SPJ4