All of the following are common causes of low engine compression except for
A. too much oil
B. defective valves.
C. weak piston rings.
D. bent pushrods
Answers
Answer:
B
Explanation:
Over filling of oil on an engine will not cause loss of compression. The crankshaft splashes it inside the engine and will come out the dip stick tube and breather on valve cover and it may splash up to the bottom of the pistons and force oil to the top through the rings
Related Questions
the concept of natural rights that came out of the enlightenment led to several political formulations of what natural rights were. which of the following was the first declaration of natural rights that applied to all men, no matter the color of their skin? group of answer choices declaration of rights and sentiments (1848) declaration of the rights of woman (1791) magna carta (1215) declaration of independence (1776) declaration of the rights of man and citizen (1789)
Answers
The declaration that was the first to apply natural rights to all men, regardless of the color of their skin, among the options you provided, is the "Declaration of the Rights of Man and Citizen" (1789).
This document was the first declaration of natural rights that applied to all men, regardless of their skin color. It was a key political formulation of the concept of natural rights that emerged during the Enlightenment. The Declaration of Independence (1776) was also a significant political formulation of natural rights, but it applied only to white men at the time of its writing. The Magna Carta (1215) was an important legal document that established certain rights and liberties for English nobles and freemen, but it did not apply to all men or address natural rights specifically. The Declaration of the Rights of Woman (1791) and the Declaration of Rights and Sentiments (1848) were important feminist documents that advocated for women's rights, but they did not apply to all men or address natural rights specifically.
Learn more about natural rights:
https://brainly.com/question/20887193
#SPJ11
note that tje dimensions are shown with respect to horizontal and vertical tangent lines the circle. y r = 5 in С 10 in 6 in 1 1 X (10 in.
Answers
The main answer is: The given information does not provide enough context to determine the specific question being asked.
What can be inferred from the given dimensions and tangent lines of the circle?Based on the given information, it is unclear what specific question is being asked. Without additional context or clarification, it is not possible to determine the relationship between the dimensions, tangent lines, and the circle. It is essential to provide more information or specify the desired outcome in order to provide a meaningful answer.
Understanding the relationship between dimensions, tangent lines, and circles can be explored through various geometric concepts and principles. Exploring topics such as circle properties, tangent lines, and their intersections can shed light on the connections between these elements.
By delving into the principles of geometry, one can gain a deeper understanding of how different geometric elements interact and influence one another.
Learn more about: tangent lines
brainly.com/question/23416900
#SPJ11
Machine quartile picnicking character which of these words does the k indicate it is greek
Answers
The letter "k" in the word "quartile" does not indicate that it is Greek. It is more likely influenced by the Latin origin of the word.
In the English language, the letter "k" is not typically associated with Greek words. Greek words usually use the Greek alphabet, which does not include the letter "k" but has a similar-sounding letter "κ" (kappa). The word "quartile" itself is derived from the Latin word "quartus," meaning "fourth." It is used in statistics to divide a distribution into four equal parts.
Greek words, on the other hand, often use letters like alpha (α), beta (β), gamma (γ), and so on. These letters are distinct from the letter "k." For example, the Greek word for "fourth" is "τέταρτος" (tétartos), which does not have a "k" sound.
Therefore, in the context of the word "quartile," the letter "k" does not indicate that it is Greek. It is more likely influenced by the Latin origin of the word.
Learn more about quartile here
https://brainly.com/question/31922534
#SPJ11
4. 7 Problems in this exercise assume that the logic blocks used to implement a processor's datapath have the following latencies: Mom/ Register D. Mom File 250ps 150 ps ALU Adder 25ps 200 ps 150ps Single Register Register gate Read Setup 5ps 30ps 20ps Sign extend Control 50ps 50ps "Register read" is the time needed after the rising clock edge for the new register value to appear on the output. This value applies to the PC only. "Register setup" is the amount of time a register's data input must be stable before the rising edge of the clock. This value applies to both the PC and Register File. 4. 7. 1 (5) <$4. 4> What is the latency of an R-type instruction (1. E. , how long must the clock period be to ensure that this instruction works correctly)? 4. 7. 2 [10] <$4. 4> What is the latency of ld? (Check your answer carefully. Many students place extra muxes on the critical path. ) 4. 7. 3 [10] <$4. 4> What is the latency of sd? (Check your answer carefully. Many students place extra muxes on the critical path. ) 4. 7. 4 (5) <84. 4> What is the latency of beq? 4. 7. 5 (5) <$4. 4> What is the latency of an I-type instruction? 4. 7. 6 (5) <$4. 4> What is the minimum clock period for this CPU?
Answers
The minimum clock period for this CPU should be at least 345 ps.
To determine the latencies and clock period requirements for different instructions in the given exercise, we will consider the provided values for the logic block latencies.
4.7.1:
The latency of an R-type instruction refers to the time required for the instruction to complete its execution. In this case, the R-type instruction consists of register read, ALU operation, and register write. From the given values, we can determine the total latency by summing the latencies of the logic blocks involved:
Latency = Register Read + ALU Adder + Register Write
Latency = 150 ps + 25 ps + 150 ps
Latency = 325 ps
Therefore, the clock period should be at least 325 ps to ensure the correct execution of an R-type instruction.
4.7.2:
The latency of ld (load) instruction represents the time required to complete the load operation, which involves register read, sign extension, ALU operation, and register write. Adding up the latencies of the involved logic blocks:
Latency = Register Read + Sign Extend + ALU Adder + Register Write
Latency = 150 ps + 20 ps + 25 ps + 150 ps
Latency = 345 ps
Thus, the clock period should be at least 345 ps for the correct execution of the ld instruction.
4.7.3:
Similar to the ld instruction, the sd (store) instruction involves register read, sign extension, ALU operation, and register write. Adding up the latencies:
Latency = Register Read + Sign Extend + ALU Adder + Register Write
Latency = 150 ps + 20 ps + 25 ps + 150 ps
Latency = 345 ps
The clock period should be at least 345 ps for the correct execution of the sd instruction.
4.7.4:
The latency of beq (branch equal) instruction involves register read, ALU operation, and control logic. Summing up the latencies:
Latency = Register Read + ALU Adder + Control
Latency = 150 ps + 25 ps + 50 ps
Latency = 225 ps
A clock period of at least 225 ps is required for the correct execution of the beq instruction.
4.7.5:
The I-type instruction refers to the load and store instructions (ld and sd). Since we have already determined their latencies in previous questions:
I-type Instruction Latency = Latency of ld or sd = 345 ps
4.7.6:
The minimum clock period for this CPU would be equal to the highest latency among all the instructions. From the previous calculations, the highest latency is 345 ps.
Therefore, the minimum clock period for this CPU should be at least 345 ps.
Learn more about CPU here
https://brainly.com/question/30458937
#SPJ11
which of the following statements are true regarding elastic deformation? (3 answers are correct) group of answer choices emptying and filling a reservoir would result in elastic deformation of the crust fold structures are the result of elastic deformation isostatic uplift following deglaciation represents elastic deformation stress and strain are proportional stress and strain are not proportional
Answers
The correct statements are 2, 3 and 5. Elastic deformation is a temporary deformation of a material. When a force is applied to a material, it will deform, and the amount of deformation will be proportional to the force applied.
Elastic deformation refers to the reversible deformation of a material when a force is applied and it is released. When the load is removed, the material will return to its original shape. Elastic deformation is characterized by its capability to withstand stress without causing any permanent change in the shape of the material or its molecular structure. The following are the correct statements regarding elastic deformation: Stress and strain are proportional; hence, when stress is applied, the deformation or strain is proportional to the stress. Isostatic uplift following deglaciation represents elastic deformation. This statement is correct. Fold structures are the result of elastic deformation. This statement is correct.
Therefore, If the force is removed, the material will return to its original state. The explanation for elastic deformation is that the stress and strain are proportional, and the deformation will not cause any permanent change in the shape or molecular structure of the material.
To know more about force visit:
brainly.com/question/30507236
#SPJ11
a three-point testcross is performed to obtain data for gene mapping. a coefficient of coincidence of 2.0 is obtained. a coefficient of coincidence of 2.0 means that
Answers
To gather information for gene mapping, a three-point testcross is conducted. A 2.0 coefficient of coincidence is found.
What does 3 point test cross mean?In genetics, a three-point cross is used to locate three genes in an organism's genome. Grading of the progeny's phenotypes is done by mating a homozygous recessive individual with a person who is heterozygous for three mutations.
What are two and three factor cross?The order of the two genes cannot be determined by a two-factor cross, but it can inform us about the distance between the two genes. A three-factor cross research, however, focuses on three connected genes and can Tell us the distances between each pair of genes and the order in which the three genes are located on their chromosome.
To know more about three-point testcross visit:-
https://brainly.com/question/14918199
#SPJ4
A company wants to develop audio speakers using an inexpensive type of plastic that has a very high quality of sound output. Which customers would most likely give a high evaluation of this product?
Answers
Answer:A
Explanation:
Those who want to save money and will use the product for only a few years
Answer:
THE ANSWER is A - those who want to save money and will use the product for only a few years
Explanation: Got it right on edg 2021
Consider steady heat transfer through the wall of a room in winter. The convection heat transfer coefficient at the outer surface of the wall is three times that of the inner surface as a result of the winds. On which service of the wall, do you think the temperature will be closer to the surrounding air temperature?
Answers
Answer:
The temperature of the outer wall surface will be closer to the temperature of the surrounding air.
Explanation
Since the outer wall has a convective heat transfer coefficient that is 3 time the one in the inner surface due to the wind, the outer wall will have a temperature closer to the surrounding air's temperature because the heat that flows from the warmer inner room wall will be rapidly conducted away from the surface of the outer wall by the prevailing wind, leaving it with a reduced temperature that will be closer to the temperature of the surrounding air.
.If two hosts are connected by five networks, how many routers will there be when one host sends a packet to the other host?
2
4
5
1
Answers
In this scenario, there would be four routers involved when one host sends a packet to the other host. Option B
The number of routers required for communication between two hosts connected by five networks depends on the topology and configuration of the network. Each network typically requires at least one router to connect it to other networks.
Assuming a simple scenario where each network is connected to the next network using a router, we can determine the number of routers needed. In this case, the number of routers will be equal to the number of networks minus one.
Given that there are five networks connecting the two hosts, the number of routers required would be:
Number of routers = Number of networks - 1
= 5 - 1
= 4
Therefore, in this scenario, there would be four routers involved when one host sends a packet to the other host.
It's important to note that this answer assumes a basic topology where each network is connected to the next using a router. In more complex network configurations, such as hierarchical or mesh topologies, the number of routers may vary.
Additionally, other factors like network redundancy, load balancing, or network protocols can also influence the number of routers involved in the communication between two hosts. Option B
For more such questions on routers visit:
https://brainly.com/question/29564882
#SPJ11
[FILL IN THE BLANK] A project estimator is working on estimates for a project that is very similar to a previous project, in that it has many of the same features and those features have similar costs. Each feature or deliverable will represent the same percentage of the total cost as it did for the previous project. He is using the _________ method of top-down estimating.A) ratioB) consensusC) apportionD) function pointE) learning curves
Answers
A project estimator is working on estimates for a project that is very similar to a previous project, in that it has many of the same features and those features have similar costs. Each feature or deliverable will represent the same percentage of the total cost as it did for the previous project. He is using the ratio method of top-down estimating. So, the correct option is A.
In top-down estimating, the project's cost is estimated using information from past similar projects as a guide. For this method, historical data is utilized to calculate the approximate cost and duration of the project as a whole. In a nutshell, top-down estimating is the opposite of bottom-up estimating. In contrast, bottom-up estimating starts with the smallest parts of the project and works its way up to the total cost and duration.
You can learn more about estimator at: brainly.com/question/17961193
#SPJ11
A horizontal force P is applied to a 130 kN box resting on a 33 incline. The line of action of P passes through the center of gravity of the box. The box is 5m wide x 5m tall, and the coefficient of static friction between the box and the surface is u=0.15. Determine the smallest magnitude of the force P that will cause the box to slip or tip first. Specify what will happen first, slipping or tipping.
Answers
Answer:
SECTION LEARNING OBJECTIVES
By the end of this section, you will be able to do the following:
Distinguish between static friction and kinetic friction
Solve problems involving inclined planes
Section Key Terms
kinetic friction static friction
Static Friction and Kinetic Friction
Recall from the previous chapter that friction is a force that opposes motion, and is around us all the time. Friction allows us to move, which you have discovered if you have ever tried to walk on ice.
There are different types of friction—kinetic and static. Kinetic friction acts on an object in motion, while static friction acts on an object or system at rest. The maximum static friction is usually greater than the kinetic friction between the objects.
Imagine, for example, trying to slide a heavy crate across a concrete floor. You may push harder and harder on the crate and not move it at all. This means that the static friction responds to what you do—it increases to be equal to and in the opposite direction of your push. But if you finally push hard enough, the crate seems to slip suddenly and starts to move. Once in motion, it is easier to keep it in motion than it was to get it started because the kinetic friction force is less than the static friction force. If you were to add mass to the crate, (for example, by placing a box on top of it) you would need to push even harder to get it started and also to keep it moving. If, on the other hand, you oiled the concrete you would find it easier to get the crate started and keep it going.
Figure 5.33 shows how friction occurs at the interface between two objects. Magnifying these surfaces shows that they are rough on the microscopic level. So when you push to get an object moving (in this case, a crate), you must raise the object until it can skip along with just the tips of the surface hitting, break off the points, or do both. The harder the surfaces are pushed together (such as if another box is placed on the crate), the more force is needed to move them.
The figure below appeared three heat treatments processes of steel (A, B and C),
select only One and answer the following:
1- Named the heat treatment process.
2- The temperature range of heating process.
3- The cooling process method.
4- The aims of process.
Answers
Answer:
b
Explanation:
Saturated refrigerant-134a vapor at 15 psia is compressed reversibly in an adiabatic compressor to 80 psia. Determine the work input to the compressor. Use the tables for R-134a.
Answers
The initial enthalpy and the entropy of the saturated water can be found out from the table of A-12E
i.e. \($h_1= 101 \ \text{Btu/lbm}$\)
\($s_1 = 0.22717 \text{ Btu/lbmR}$\)
Since the process mentioned above is an adiabatic compression process, the entropy will remain constant throughout the process. Therefore, we take the value of entropy and the final pressure using the table with few interpolations and also approximations to find the final enthalpy. It is given by :
\($h_2= 116.09 \text{ Btu/lbm}$\)
So the work input from the energy balance equation :
\($\dot{W} + \dot{m}h_1 = \dot{m}h_2$\)
\($w=h_2 - h_1$\)
= 116.09 - 101
= 15.09
Therefore, \($w= 15.09 \text{ Btu/lbm}$\)
ASAP PLease electrical engineering problem
Answers
Answer:
see attached
Explanation:
As you know, a full adder produces the binary value in (carry, output) that is the the number of true input bits among the (carry in, A, B) inputs.
The annotated diagram attached shows the bit values for a 4-bit full adder/subtractor.
__
Additional comment
If the numbers are considered "signed", then the top diagram will generate an "overflow" based on the difference between the carry C4 and the output O4.
how can you add an angle to all extruded faces of a feature
Answers
Stretching a flat, 2D shape vertically to produce a 3D item in a scene is called extrusion. For instance, extruding building polygons by a height value can result in three-dimensional building shapes.
By applying a force that causes the material to flow through an opening or die, a process known as extrusion allows a material to be plastically deformed. If the substance possesses the necessary qualities, it will adopt the cross-sectional profile of the die and keep that form in the final extrudate. The playdough toys used when playing with it are a straightforward illustration of extrusion. Playdough is forced through the die to form a certain shape, and the procedure is known as extrusion. The substance must be forced through the die firmly in order for it to produce the correct form.
Learn more about Extrusion here
https://brainly.com/question/16022996
#SPJ4
Hi all any one help me??
Answers
Answer:
Explanation:
sorry i dont know
A cylindrical bar of metal having a diameter of 20.5 mm and a length of 201 mm is deformed elastically in tension with a force of 46300 N. Given that the elastic modulus and Poisson's ratio of the metal are 60.5 GPa and 0.33, respectively, determine the following: (a) The amount by which this specimen will elongate in the direction of the applied stress. (b) The change in diameter of the specimen. Indicate an increase in diameter with a positive number and a decrease with a negative number.
Answers
Answer:
a) The amount by which this specimen will elongate in the direction of the applied stress is 0.466 mm
b) The change in diameter of the specimen is - 0.015 mm
Explanation:
Given the data in the question;
(a) The amount by which this specimen will elongate in the direction of the applied stress.
First we find the area of the cross section of the specimen
A = \(\frac{\pi }{4}\) d²
our given diameter is 20.5 mm so we substitute
A = \(\frac{\pi }{4}\) ( 20.5 mm )²
A = 330.06 mm²
Next, we find the change in length of the specimen using young's modulus formula
E = σ/∈
E = P/A × L/ΔL
ΔL = PL/AE
P is force ( 46300 N), L is length ( 201 mm ), A is area ( 330.06 mm² ) and E is elastic modulus (60.5 GPa) = 60.5 × 10⁹ N/m² = 60500 N/mm²
so we substitute
ΔL = (46300 N × 201 mm) / ( 330.06 mm² × 60500 N/mm² )
ΔL = 0.466 mm
Therefore, The amount by which this specimen will elongate in the direction of the applied stress is 0.466 mm
(b) The change in diameter of the specimen. Indicate an increase in diameter with a positive number and a decrease with a negative number.
Using the following relation for Poisson ratio
μ = - Δd/d / ΔL/L
given that Poisson's ratio of the metal is 0.33
so we substitute
0.33 = - Δd/20.5 / 0.466/201
0.33 = - Δd201 / 20.5 × 0.466
0.33 = - Δd201 / 9.143
0.33 × 9.143 = - Δd201
3.01719 = -Δd201
Δd = 3.01719 / - 201
Δd = - 0.015 mm
Therefore, The change in diameter of the specimen is - 0.015 mm
Hey guys can anyone list chemical engineering advancement that has been discovered within the past 20 years
Answers
Nanopesticides. The world population keeps growing. ...
Enantio selective organocatalysis. ...
Solid-state batteries. ...
Flow Chemistry. ...
Porous material for Water Harvesting. ...
Directed evolution of selective enzymes. ...
From plastics to monomers. ...
What is the acceleration of a 0.8 kg vehicle powered by 0.07 N of force?
Answers
Using the Newton's second law of motion we will see that the acceleration is 0.0875 m/s^2.
What is the acceleration of the vehicle?The acceleration of a vehicle is determined by the force acting on it and its mass, as described by Newton's second law of motion:
F = m * a
where F is the force acting on the object, m is the mass of the object, and a is the resulting acceleration.
In this case, the force acting on the vehicle is 0.07 N, and the mass of the vehicle is 0.8 kg. Substituting these values into the equation above, we get:
0.07 N = 0.8 kg * a
Solving for a, we get:
a = 0.07 N / 0.8 kg
a = 0.0875 m/s^2
Therefore, the acceleration of the 0.8 kg vehicle powered by 0.07 N of force is 0.0875 m/s^2.
Learn more about acceleration at:
https://brainly.com/question/460763
#SPJ1
Which of the following power tools has a revolving vertical shaft and a cutter? *
1 point
a) saber saw
b) router
c) miter saw
d) circular saw
Answers
The tool that has a revolving vertical shaft and a cutter is a router. The correct option is b.
What are power tools?There are many different kinds of power tools, including portable power tools like a circular saw, heat guns, and wall chasers as well as electrical power tools like impact wrenches, lathes, power drills, power ratchet sets, and power saws.
Power tools including circular saws, jigsaws, drills, hammer drills, sanders, grinders, routers, and many others reduce labor and time requirements. The requirement for knowledge of the risks that power tools provide if used improperly is raised due to their rising use.
A power tool called a router has a flat base and a spinning blade that protrudes beyond the base. An electric motor or a pneumatic motor can drive the spindle.
Therefore, the correct option is b) router.
To learn more about power tools, refer to the link:
https://brainly.com/question/30115428
#SPJ6
technician A says that many port fuel-injection systems on four-cylinder engines use a simultaneous firing of injectors. Technician B says that sequential fuel injectors are timed and pulsed individually, much like the spark plugs are sequentially operated in firing order of the engine. Who is correct
Answers
In the two scenario above concerning port fuel-injection and sequential fuel injectors, only Technician b is correct.
How many injectors can be found in a 4 cylinder?A vehicle often has one fuel injector per cylinder and if one has a four-cylinder car, it would also have four fuel injectors.
Note that Fuel-pressure regulators that are found on a port fuel-injected systems is one that often work with injector pressures that is said to be of 30 to 55 PSI.
Learn more about Technician from
https://brainly.com/question/5122191
What is true about delay skew? a. delay skew is only a problem with coaxial cables b. delay skew exists in UTP cables (e.g., Cat 5E) where each wire pair is twisted at different twist ratios c. delay skew only exists in unguided systems where path reflection causes signal copies to reach the receiver at different times d. delay skew is another term for signal propagation
Answers
Delay skew is a phenomenon that exists in UTP cables (e.g., Cat 5E) where each wire pair is twisted at different twist ratios. This means that option b is the correct answer.
Delay skew is not only a problem with coaxial cables (option a), it does not only exist in unguided systems where path reflection causes signal copies to reach the receiver at different times (option c), and it is not another term for signal propagation (option d). Therefore, the true statement about delay skew is that it exists in UTP cables where each wire pair is twisted at different twist ratios. Delay skew can cause errors in data transmission and should be accounted for in a system's design.
Here you can learn more about UTP cables https://brainly.com/question/13362491
#SPJ11
A small single-cylinder, two-stroke cycle SI engine operates at 4000 rpm with a
compression ratio of 9. At this speed, the engine produces 5 kW of brake power. If
the engine is square with a total displacement volume of 150 cm3
, calculate:
1- Cylinder bore and piston stroke (mm).
2- Crank offset (mm).
3- Average piston speed (m/s).
4- Clearance volume (cm3
).
5- Brake output per total displacement (kW/liter).
6- Number of cycles performed in one second
7- Speed of rotation of the camshaft (rpm)
Answers
state the three integrity rules. indicate the reasons for enforcing each rule
Answers
There are three integrity rules that are commonly enforced to maintain the accuracy and consistency of data in databases.
1. Entity Integrity Rule - This rule requires that each table in a database has a unique primary key, which cannot be null. The reason for enforcing this rule is to ensure that every record in the table can be uniquely identified, which is essential for maintaining data consistency and avoiding duplicate entries.
2. Referential Integrity Rule - This rule requires that any foreign key in a table must reference an existing primary key in another table. This ensures that data relationships between tables are maintained and that there are no orphaned records in the database. The reason for enforcing this rule is to prevent data inconsistencies that can occur when related records are deleted or modified without updating the corresponding records in other tables.
3. Domain Integrity Rule - This rule requires that all data entered into a database must be valid according to a defined set of rules or constraints. This can include data type, format, and range constraints, as well as other business rules. The reason for enforcing this rule is to ensure that the data entered into the database is accurate, complete, and consistent, and that it meets the needs of the business or organization that uses the database.
learn more about integrity here:
https://brainly.com/question/30077349
#SPJ11
Proper, smooth shifting is important because if you shift before your vehicle is ready
Answers
Proper, smooth shifting is important because shifting before your vehicle is ready will cause it to je-rk forward and your drive wheels may lock.
How to properly shift your gears?A proper, smooth shifting of the gears of an automobile vehicle is very important because shifting them before the vehicle is ready would cause the following:
Jer-king forward. Lock of the drive wheels.Loss of control of the vehicle.As a good driver, proper, smooth shifting is important because shifting before your vehicle is ready will cause it to je-rk forward and your drive wheels may lock.
Read more on good drivers here: https://brainly.com/question/1071840
#SPJ1
explain why it is not advisable to wear a ring at work shop
Answers
Answer:
Metal conducts heat so it could severely burn your finger.
Rings can create multiple hazards while working with chemicals.
Rings/Jewlery can be a "hiding place" for bacteria.
Amongst many other reasons as to why it's not advisable to wear a ring(s) at a workshop/workplace.
Where would an engineer indicate the unit of measurement used in a design
Answers
An engineer would indicate the unit of measurement used in a design in millimeters.
What are measurements?The primary unit of measurement is the stocking unit of measure for a given item in a specific organization. You must define an item attribute that serves as the primary unit of measurement when creating each item.
Because the technical drawings are scaled, engineers, architects, and builders may create the items according to exact specifications.
When understanding scales, the number on the left relates to the measurement of the drawing, while the number on the right represents the actual size of the object.
Therefore, a millimeter is used in a design.
To learn more about measurements, refer to the link:
https://brainly.com/question/28390923
#SPJ1
According to the video, what talents do Biomedical Engineers need? Check all that apply.
patience
customer service skills
communication skills
problem-solving skills
ability to handle complex calculations
assertiveness
Answers
patience
problem-solving skills
ability to handle complex calculations
Explanation:
Engineering's fundamental building block is arithmetic, and biomedical engineers unquestionably require solid maths abilities. Geometry and calculus are frequently used by biomedical engineers while assessing and developing medical solutions. Thus, option A,C,D is correct.
What talents do Biomedical Engineers require?To better the lives of patients, biomedical engineers analyse challenges in biology and medicine and create solutions. A good aptitude for engineering, an imaginative spirit, and a love for working in healthcare are all required for this position. The human anatomy fascinates biomedical engineers, and they enjoy addressing problems.
No more difficult than any other type of engineer, at least. For those with a talent for engineering, this field is rigorous but rewarding, even though it is generally difficult to break into. No engineering discipline is more demanding than biomedical engineering.
Therefore, patience, problem-solving skills, ability to handle complex calculations talents do Biomedical Engineers need.
Learn more about Biomedical Engineers here:
https://brainly.com/question/11617187
#SPJ2
2
3
TIME REMAINING
54:48
In a life-cycle assessment, the impact of demolition is determined once the building has been scheduled to be
torn down.
True
False
Mark this and totum
Save and Exit
In a life cycle assessment, the impact of demolition is determined once the building has been scheduled to be torn down?
True or false
Answers
Answer:
very confusing sorry cant help........................................................................................................................................................... i think it is true if it wrong i am so sorrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrry
Explanation:
which of the answers listed below describe(s) the features of uefi? (select all that apply)
Answers
The features of UEFI include:
1. Improved security features
2. Faster boot times
3. Support for larger hard drives
4. Flexible pre-boot environment
5. Compatibility with legacy BIOS systems (through a Compatibility Support Module)
Please note that without the specific answer choices, I cannot directly address which of them would apply. However, you can use this information to compare and select the correct options in your given list.
If you want to learn more about UEFI, click here:
https://brainly.com/question/29555346
#SPJ11