A charged particle moves with velocity v in a uniform magnetic field B. The magnetic force experienced by the particle is ___________.
A. Always zero
B. Zero if B and V are perpendicular
C. Zero if Band V are parallel
D. Zero if B and V are inclined at 45 degree

Answer:

friction

air drag

every thing that opposes the motion affects kinetic energy

Explanation:

kinetic energy is a energy which is increase with increase in motion and potential energy is energy stored while the object is at rest

potential energy ∝ 1/(kinetic energy)

as kinetic energy increases potential energy decreases

If 5.30 Nm of torque is needed to spin a handle, 33.3 J is wasted each revolution. The correct answer is b. 33.3

The handle's work can be computed using the formula:

Work = Torque × Angle

Given:

Torque = 5.30 Nm

Angle = 2π radians (since one complete revolution is equivalent to 2π radians)

Substituting the values into the formula, we get:

Work = 5.30 Nm × 2π radians

= 10.6π Nm

We can estimate 3.14:

Work  = 10.6 × 3.14 Nm = 33.284 Nm.

Therefore, each handle revolution expends 33.284 Nm, which is closest to option b) 33.3 J.

To know more about torque

https://brainly.com/question/17512177

#SPJ4

It will takes approximately 0.165 seconds for the ball to reach the floor after it has been gently pushed off the table top from a height of 1.3 m above the floor.

When an object is dropped from a height, it falls to the ground due to the force of gravity.

When an object is released from a height of 1.3 m above the ground, the time it takes to reach the ground is calculated using the formula:

h = 0.5gt²  where h is the height of the object, g is the acceleration due to gravity and t is the time taken for the object to reach the ground.

Rearranging this formula to solve for t, we have: \(t = \sqrt{(2h/g)}\)

Substituting the values we have: \(h = 1.3 mg = 9.81 m/s^{2} t = \sqrt{(2 \times 1.3 / 9.81)t} = \sqrt{(0.265 / 9.81)t} = \sqrt{0.027t } = 0.165 seconds\)

Therefore, it takes approximately 0.165 seconds for the ball to reach the floor after it has been gently pushed off the table top from a height of 1.3 m above the floor.

For more questions on force of gravity

https://brainly.com/question/18258780

#SPJ8

Displacement = Final position – initial position = 50-2=48m

Distance = speed × time= 50m.

Time  =2.3 multiply the time value by 60 we get 138 s.

Velocity =  distance /time =50 m/ 138 s=0.36 m/s

Displacement is defined as a change in an object's location. It is a vector quantity with a magnitude and a direction. It is depicted as an arrow pointing from the starting point to the ending point. For instance, if an object travels from A to B, the object's location changes.

Distance is a numerical measurement of the distance between two objects or places. Distance can refer to a physical length or an estimate based on other factors in physics or common use. The distance between two points A and B is commonly expressed as |AB|.

The primary indication of an object's position and speed is its velocity. It is defined as the distance travelled by an item in one unit of time. The displacement of an item in unit time is defined as velocity.

Learn more about velocity https://brainly.com/question/18084516

#SPJ9

Answer: Her test trials had a high level of accuracy but a low level of precision.

Explanation:

Answer:

Her test trials had a high level of accuracy but a low level of precision.

Explanation:

The process that causes water to move from Earth's surface to the atmosphere during the water cycle is called evaporation.

Evaporation is the process by which water molecules absorb energy from the surrounding environment, typically in the form of heat, and transform from a liquid state to a gaseous state (water vapor). The water molecules then rise up into the atmosphere, where they can form clouds and participate in other processes in the water cycle, such as condensation, precipitation, and surface runoff. Evaporation occurs primarily from bodies of water, such as oceans, lakes, and rivers, but also from soil, plants, and other surfaces that contain moisture.

To know more about evaporation, here

brainly.com/question/28319650

#SPJ4

Answer: 0.99m left

Explanation:

The formula:

Distance / Time = Rate

Fill in the formula

Distance / 0.55s = 1.8 m/s

Multiply both sides by 0.55s

Distance = 0.99m

Displacement = 0.99m to the left.

Answer:

-0.99 (See attached)

Explanation:

(See attached)

Answer:

balloon is rigid the amount of gas is constant inside the interior pressure of the balloon is constant and in these cities it becomes equal to or slightly higher than atmospheric pressure

Explanation:

Este ejercicio es referente a la mecánica de fluidos, usemos la expresión para la presión  

       P = ρ g h

En es el caso del balón  usemos la presión en la pared extrema, llamemos P la presión por el gas en el interior y P_ext la presión atmosférica del lugar

        cuando se llena el valor en una ciudad de baja altura la presión atmosférica es mas alta

          P_int1 < P_ext1

por lo cual la pared del balón no se mantiene rígida.

Cuando el balón es trasladado a una ciudad con mayor altura sobre el nivel del mar la presión exterior disminuye

       P_ext2 = ρ g h₂ < P_ext1

en promedio la presión disminuye con la altura  en 0,029 atm cada 250 m

por lo tanto como la cantidad de gas es constante en el interior la presión interior del globo es constante y en esta ciudades se hace igual o un poco mayor que la presión atmosférica, en consecuencia la pared del globo esta rígida

        P_int2 >P_ext2

Traslate

This exercise is related to fluid mechanics, let's use the expression for pressure

       P = ρ g h

In the case of the balloon, let's use the pressure on the extreme wall, let's call P the pressure for the gas inside and P_ext the atmospheric pressure of the place

        when the value is filled in a low-lying city the atmospheric pressure is higher

          P_int1 <P_ext1

therefore the wall of the ball does not remain rigid.

When the ball is transferred to a city with higher altitude above sea level, the external pressure decreases

       P_ext2 = ρ g h <P_ext1

on average the pressure decreases with height by 0.029 atm every 250 m

therefore as balloon is rigid the amount of gas is constant inside the interior pressure of the balloon is constant and in these cities it becomes equal to or slightly higher than atmospheric pressure, therefore the wall of the

        Pint 2> Pe

In part (b), the filling process is unable to meet the tolerance limits 99.7% of the time, and it does not achieve Six Sigma quality levels.

a. To calculate the process capability ratio (Cp) in part (a), we use the formula:

Cp = (Upper Specification Limit - Lower Specification Limit) / (6 * Standard Deviation)

Given:

Mean = 64 ounces

Standard Deviation = 8 ounces

Upper Specification Limit = 71 ounces

Lower Specification Limit = 57 ounces

Cp = (71 - 57) / (6 * 8) = 14 / 48 = 0.2917 (rounded to four decimal places)

To determine the standard deviation required for the process to meet the tolerance limits 99.7% of the time, we use the Z-score corresponding to a 99.7% confidence level, which is approximately 3.

Z = (Upper Specification Limit - Mean) / Standard Deviation

Rearranging the formula, we can solve for the standard deviation:

Standard Deviation = (Upper Specification Limit - Mean) / Z

Standard Deviation = (71 - 64) / 3 = 7 / 3 = 2.3333 (rounded to four decimal places)

b. In part (b), with the improved process having a standard deviation of 1.5 ounces, we can recalculate the process capability ratio using the same formula:

Cp = (Upper Specification Limit - Lower Specification Limit) / (6 * Standard Deviation)

Using the same specification limits as before:

Cp = (71 - 57) / (6 * 1.5) = 14 / 9 = 1.5556 (rounded to four decimal places)

To determine if the filling process is able to meet the tolerance limits 99.7% of the time, we compare the new Cp value to the critical value of 2. Since Cp is less than 2, the process does not provide Six Sigma quality levels.

To learn more about quality, click here:
brainly.com/question/33819821
#SPJ11

The measure of central tendency that should be used to calculate the cutoff time for the final race is the median.

Option C.

The median is the middle point in a dataset—half of the data points are smaller than the median and half of the data points are larger.

To find the median: Arrange the data points from smallest to largest. If the number of data points is odd, the median is the middle data point in the list.

So from the given data of the 100 meter dash, the measure of central tendency that should be used to calculate the cutoff time for the final race is the median.

The median will help to separate half of the data points that are smaller than the cutoff time and half of the data points are larger than the cutoff time.

Learn more about median here: https://brainly.com/question/26177250

#SPJ1

Answer:

A

Explanation:

Answer:

The two of the following measurements, when taken together, would allow engineers to find the total mechanical energy dissipated during the skid

B. The contact area of each tire with the track.

C. The co-efficent of static friction between the tires and the track.

D. The co-efficent of static friction between the tires and the track.

Explanation:

To calculate the book value at year 3 (BV3), we need to determine the accumulated depreciation at year 3. The depreciation is calculated by subtracting the salvage value from the initial cost and dividing it by the number of years.

Initial cost: $20,000

Salvage value: $5,000

Number of years: 5

Depreciation per year = (Initial cost - Salvage value) / Number of years

Depreciation per year = ($20,000 - $5,000) / 5 = $3,000

Accumulated depreciation at year 3 = Depreciation per year * Number of years

Accumulated depreciation at year 3 = $3,000 * 3 = $9,000

Book value at year 3 = Initial cost - Accumulated depreciation at year 3

Book value at year 3 = $20,000 - $9,000 = $11,000

Therefore, the Book Value at year 3 (BV3) is $11,000 (option d).

To calculate the depreciation at year 3 (D3), we can simply use the depreciation per year, which is $3,000. Therefore, the Depreciation at year 3 (D3) is $3,000 (option b).

Learn more about depreciation here:

https://brainly.com/question/29894489

#SPJ11

Electric field strength and length (distance) will be measured directly in the electric field plotting lab.

option C

In an electric field plotting lab, the goal is to measure the strength of the electric field at various points in space.

The electric field strength can be determined by measuring the voltage difference across a known distance in the field. By plotting these points, you can create a graphical representation of the electric field and observe how the field changes with distance.

Voltage is a measure of the electrical potential difference between two points, while electric field strength is a measure of the force experienced by a charged particle in the field.

Therefore, the quantities that will be measured directly in the electric field plotting lab are electric field strength and length (distance).

Learn more about electric field here: https://brainly.com/question/14372859

#SPJ1

The total mechanical energy of the system change into its motion as the ball rolls down the ramp.

As the ball rolls down on the ramp, the potential energy is converted to kinetic energy. If there is no friction, all of the energy is converted into kinetic energy which leads to increase in the motion of the ball.

So we can conclude that the total mechanical energy of the system change into its motion as the ball rolls down the ramp.

Learn more about energy here: https://brainly.com/question/13881533

#SPJ1

Answer:

no i did not observe anything

Explanation:

When air (ideal gas) moves from a region of high pressure to a region of low pressure, with no addition or subtraction of heat, it expands.

Isothermal expansion of an ideal gas involves increase in the gas volume at constant temperature. The volume of the gas increases while its pressure decreases.

When air moves from a region of high pressure to a region of low pressure, it is no longer adiabatic (constant pressure).

Thus, when air (ideal gas) moves from a region of high pressure to a region of low pressure, with no addition or subtraction of heat, it expands.

Learn more about Isothermal expansion here: https://brainly.com/question/17192821

Answer:

I don't know if I can help you with that

Answer: Force

In physical science, a force is something that acts on an object by pushing or pulling it. If the force is strong enough, it changes the position or shape of the object. Forces such as friction, air resistance and simple physical contact touch the object directly, while forces like gravity, magnetism and electrostatics act on the object from a distance. Force is a vector quantity, meaning you can measure both its strength and its direction. The formula to find the measure of a force is force = mass times acceleration, written as f = ma.

Velocity

The faster something is moving, the higher its velocity.

When an object is moving, one way to measure how fast it is moving is by finding its velocity, which is the rate at which it is changing position. Like force, velocity is a vector quantity, so it includes direction. To find the average velocity of an object, divide the change in its position by the time the movement took, and state its direction. For example, if a car is driving north and in one hour's time it travels 30 miles, its velocity is 30 miles per hour, north.

\_:Peepato1234:_/

The erector spinae muscles are a group of muscles that extend along the back of the spine. The origin of the erector spinae muscle group is complex, and it varies depending on the specific muscle within the group.

What is Erector Spinae?

The erector spinae muscles are responsible for extending the spine, or bending the spine backwards, as well as for helping to maintain proper posture and balance. They also play a role in lateral flexion and rotation of the spine. These muscles are important for many everyday activities, such as standing, walking, lifting, and bendin

The erector spinae muscles are important for maintaining proper posture, supporting the spine, and allowing movement of the back. They are also involved in activities that require bending, twisting, and lifting.

Learn more about Erector Spinae from the given link

https://brainly.com/question/19438625

#SPJ4

The equivalent resistance of the 3.89 Ω, 7.75 Ω, and 9.05 Ω resistors connected in series with a 12.0 V battery is 20.69 Ω.

The equivalent resistance of resistors connected in series is equal to the sum of the resistance of each resistor. Therefore, the equivalent resistance is: R = 3.89 Ω + 7.75 Ω + 9.05 Ω = 20.69 Ω

So, the equivalent resistance of the 3.89 Ω, 7.75 Ω, and 9.05 Ω resistors connected in series with a 12.0 V battery is 20.69 Ω.

The equivalent resistance of an electrical circuit refers to the single resistance that would have the same effect as the combination of multiple resistors in the circuit. It is a measure of the total opposition to current flow in the circuit. The equivalent resistance can be found by using various methods such as series, parallel, and combination circuits. The equivalent resistance of a circuit depends on the individual resistances, the connections between them, and the voltage and current in the circuit.

To know more about equivalent resistance refer to-

brainly.com/question/13606415#

#SPJ11

Answer:

A Van Allen radiation belt is a zone of energetic charged particles, most of which originate from the solar wind, that are captured by and held around a planet by that planet's magnetosphere. Earth has two such belts, and sometimes others may be temporarily created

Answer:

I think D

Explanation:

Answer:

heat occurs to change into solid

Answer:

It's freezing or solidification

Explanation:

The coldness freezes the water making it a solid, like water to an ice cube. Take Disney's Frozen by example. Elsa has a ice touch, so when she touches water, it becomes a solid.

Scientists are confident that they have succeeded in making a detection when they have observed a signal that is consistent with the predicted characteristics of the phenomenon they are trying to observe.

When this signal is statistically significant, meaning that it is unlikely to have occurred by chance. For example, in the case of gravitational wave detection, scientists use highly sensitive detectors, such as the Laser Interferometer Gravitational-Wave Observatory (LIGO) to measure minuscule distortions in space-time caused by passing gravitational waves.

When the data from the detectors is analyzed, scientists look for signals that match the predicted waveform of a gravitational wave. They also use statistical methods to determine the probability that the observed signal is not just random noise.

If the observed signal matches the predicted waveform and has a low probability of occurring by chance, scientists can be confident that they have made a detection. However, it is important to note that these detections are often very difficult to make and require a high level of precision and accuracy in both the instruments and the analysis techniques used.

Therefore, scientists also subject their findings to rigorous peer review and validation by independent researchers to confirm the validity of their results.

Learn more about LIGO here:- brainly.com/question/30722973

#SPJ11

Well we know the hypotenuse of the triangle which is 253 m. And we know the angle of the triangle which is 55.8 degrees. So we want to find y. And to find y we use sin. And sin is a ratio, the ratio of the opposite leg, and hypotenuse. So sin(55.8) = y/253. Now we solve for y by multiplying both sides by 253. And finally we get 209.25 as the length of the y component.

Answer:

1. 50m

2. they are motionless

3. 20s

4. time

5. distance

The mass will travel 28 m distance before coming to rest.

There are three equations of motion. We will use the second equation of motion to find the distance traveled by the object before rest.

When an object is moving up the plane, there is the force of gravity acting downward on the object. So, acceleration in the object is acceleration due to gravity.

We are given,

Initial speed = 8.5 m/s2

angle with horizontal = 25°

Final speed = 0

Acceleration = g sin25

We use equation of motion to find final distance.

\(V_{f ^{2}\) = \(V_{i^{2}\) + 2a ( \(x_{f\) - \(x_{i\) )

0   = \(8.5^{2}\) + 2 × 9.8 sin 25 (\(x_{f\) - 0)

0 = 72.25 + 19.6 (-0.132)  \(x_{f\)

\(x_{f\) = 72.25÷2.58= 28 m

To know more about acceleration due to gravity here

brainly.com/question/13860566

#SPJ4

The 13th Amendment to the United States Constitution provides that "Neither slavery nor involuntary servitude, except as a punishment for crime whereof the party shall have been duly convicted, shall exist within the United States, or any place subject to their jurisdiction."

In other words:

Nobody can be a slave or work against their will in any place controlled by the USA, except if they're sentenced to jail or prison for a crime.

The 13th amendment, which was adopted by Congress on Jan 31, 1865, and ratified by the states on December 6, 1865, declared slavery to be illegal throughout the country and in any location under their jurisdiction. It also states that "Neither “ neither slavery nor involuntary, except as a punishment for offense whereof the group shall have indeed been duly found guilty, shall exist."

An amendment can change or add to the terms of a contract or other legal document. A latest arrival or alteration to a document that substantially preserves its integrity is called an amendment.

Common synonyms for amend include correct, emend, rectify, redress, reform, remedy, and revise. All of these words pertain to "setting right what's genuinely wrong," but only amend, reform, and revise suggest improvement via corrective revisions, with amend often denoting minor changes alter a law.

To know more about Amendment visit:

https://brainly.com/question/12124635

#SPJ4

The processes under chemical change are: cooking an egg, fireworks exploding, and rusting of a metal tool.

The processes under physical change are: melting ice, evaporating puddle of water, and dissolving of salt in water.

Given:

The following process:

To find:

The classify the processes in whether it does or does not produce a new substance.

Solution:

Chemical change, due to change in atomic arrangement egg get solidified on cooking, a new substance is formed.

Physical change, change in the state of matter is taking from solid to liquid, no new substance is formed.

Chemical change. formation of carbon dioxide gas and sound energy, anew substance formed

Physical change, change in the state of matter is taking from liquid to gas, no new substance is formed.

Chemical change, formation of oxides on the surface of the metal tool due to reaction between air and metal, a new substance is formed.

Physical change, ions of salt in the solid state are changing into aqueous ions with no formation of new substance, no new substance is formed.

The processes under chemical change are: cooking an egg, fireworks exploding, and rusting of a metal tool.

The processes under physical change are: melting ice, evaporating puddle of water, and dissolving of salt in water.

Learn more about physical change and chemical change here:

brainly.com/question/864557?referrer=searchResults

brainly.com/question/13316655?referrer=searchResults