a 60 cm-long, 3 cm-diameter aisi 1010 steel rod is welded to a furnace wall and passes through 20 cm of insulation before emerging into the surrounding air. the faurnace wall is at 300oc and the air temperature is 20oc. estimate the temperature of the bar tip if the heat transfer coefficient between the rod and air is taken to be 13 w/m2 k.
Answers
We may calculate the temperature of the bar tip using the boundary conditions and the one-dimensional heat conduction equation: q/A = -k(dT/dx).
Which of the following define the one-dimensional heat equation's boundary conditions?Boundary circumstances: Particular actions at x0 = 0 and L: 1. Temperature constant: u(x0,t) = T for t > 0. 2. Insulated end: for t > 0, ux
Q = hA(T s - T air), where (x0,t) = 0
When we combine these equations, we obtain:
(T s - T air) = -(k/h)(dT/dx), where hA(T s - T air)/A = -k(dT/dx).
Assuming that the temperature gradient is constant over the length of the rod and integrating both sides from x = 0 to x = L, we arrive at:
(T s - 20) = -(43.5e-3 / 13)(T s - 300)*0.6 (T s - T air) = -(k/h)(T s - T furnace)*L
Simplifying:
(T s - 20) = -1.008(T s - 300)
T s - 20 = -1.008T s + 302.4 when expanded
When we solve for T s, we obtain T s = 1265.4 K.
To know more about equation visit"-
https://brainly.com/question/24179864
#SPJ1
Related Questions
forging produces parts with equivalent strength, toughness and ductility to group of answer choices none of the other answers are correct cold chamber die casting hot chamber die casting sand castling investment casting
Answers
Forging produces parts with equivalent strength, toughness, and ductility to hot chamber die casting. Forging is a manufacturing process in which metal is pressed or hammered into shape.
Forging is accomplished by applying high pressure to a metal piece in order to bend and shape it into the desired shape. The three main forging processes are Impression die forging; Cold forging, also known as a cold heading; Open-die forging. Impression dies forging. The forging method in which the metal is pounded or squeezed between two dies, typically the top and bottom are known as impression die forging. The material conforms to the form of the dies as a result of the process. Cold forging, also known as a cold heading. In the case of cold forging, also known as cold heading, the metal is hammered or squeezed under extreme pressure at room temperature. Cold forging is used to produce complex shapes in large numbers, including screws and bolts.
Open-die forging, also known as free forging, is the process of shaping metal between two flat dies. It's usually used to create simple shapes like cylinders and discs. The equivalent strength, toughness, and ductility of hot chamber die casting can be achieved with forging. The process of melting metal and forcing it into a die under high pressure is known as hot chamber die casting. This approach is ideal for producing a large number of small to medium-sized components with excellent precision and detail. Hot chamber dies casting is commonly used in the production of toys, car parts, and hardware because of its consistency and efficiency. In comparison to other manufacturing processes, hot chamber dies casting is quick, precise, and provides parts with excellent mechanical properties. Thus, from the above explanation, it is clear that forging produces parts with equivalent strength, toughness, and ductility to hot chamber die casting.
To learn more about Forging :
https://brainly.com/question/14940744
#SPJ11
When traveling at higher speeds (40 mph or faster), the most fuel efficient way to keep the car cool is to
Answers
Answer:
When traveling at higher speeds (40 mph or faster), the most fuel-efficient way to keep the car cool is to follow these tips:
1. Use the vehicle's ventilation system: Instead of relying on air conditioning, use the car's ventilation system to circulate fresh air from outside. This helps to cool down the interior without putting extra load on the engine, thus saving fuel.
2. Close windows and sunroofs: To reduce wind resistance and drag, close all windows and sunroofs while driving at higher speeds. Open windows create drag, which can increase fuel consumption.
3. Park in the shade: Whenever possible, park your car in a shaded area to avoid excessive heating when it's not in use. This can help keep the car cooler and reduce the need for extra cooling when you start driving.
4. Use reflective sunshades or window tinting: Use reflective sunshades on your windshield and window tinting on side windows to reduce the amount of heat entering the car. This can help keep the interior cooler, reducing the need for excessive cooling while driving.
5. Maintain your vehicle: Regular maintenance, such as checking and replacing coolant, inspecting the radiator, and ensuring proper functioning of the engine cooling system, can help keep your car running efficiently and prevent overheating.
6. Plan your trips strategically: If possible, try to avoid driving during the hottest part of the day. By planning your trips to avoid peak temperatures, you can reduce the strain on your vehicle's cooling system and minimize the need for excessive cooling.
Remember that these tips are specifically focused on keeping the car cool while maintaining fuel efficiency at higher speeds. In certain circumstances, such as extremely hot weather, using the air conditioning sparingly may be necessary for passenger comfort, but it will increase fuel consumption.
A horizontal force P is applied to a 130 kN box resting on a 33 incline. The line of action of P passes through the center of gravity of the box. The box is 5m wide x 5m tall, and the coefficient of static friction between the box and the surface is u=0.15. Determine the smallest magnitude of the force P that will cause the box to slip or tip first. Specify what will happen first, slipping or tipping.
Answers
Answer:
SECTION LEARNING OBJECTIVES
By the end of this section, you will be able to do the following:
Distinguish between static friction and kinetic friction
Solve problems involving inclined planes
Section Key Terms
kinetic friction static friction
Static Friction and Kinetic Friction
Recall from the previous chapter that friction is a force that opposes motion, and is around us all the time. Friction allows us to move, which you have discovered if you have ever tried to walk on ice.
There are different types of friction—kinetic and static. Kinetic friction acts on an object in motion, while static friction acts on an object or system at rest. The maximum static friction is usually greater than the kinetic friction between the objects.
Imagine, for example, trying to slide a heavy crate across a concrete floor. You may push harder and harder on the crate and not move it at all. This means that the static friction responds to what you do—it increases to be equal to and in the opposite direction of your push. But if you finally push hard enough, the crate seems to slip suddenly and starts to move. Once in motion, it is easier to keep it in motion than it was to get it started because the kinetic friction force is less than the static friction force. If you were to add mass to the crate, (for example, by placing a box on top of it) you would need to push even harder to get it started and also to keep it moving. If, on the other hand, you oiled the concrete you would find it easier to get the crate started and keep it going.
Figure 5.33 shows how friction occurs at the interface between two objects. Magnifying these surfaces shows that they are rough on the microscopic level. So when you push to get an object moving (in this case, a crate), you must raise the object until it can skip along with just the tips of the surface hitting, break off the points, or do both. The harder the surfaces are pushed together (such as if another box is placed on the crate), the more force is needed to move them.
a what type of contact is used with the High pressure switch?
Answers
why you so mean to me? leave my questions please. answer them
Answers
Answer: Why is even here then.
Explanation:
The predator uav has the following characteristics: has the following characteristics: wingspan = 14.85 m, wing area = 11.45 m2, maximum weight = 1020 kgf, and fuel weight = 295 kgf. the power plant is a rotax four-cylinder, four-stroke engine of 85 horsepower driving a two-blade, variable-pitch pusher propeller. assume that the oswald efficiency factor is 0.7, the zero-lift drag coefficient is 0.03, the propeller efficiency is 0.9, and the specific fuel consumption is 0.2 kgf of fuel per horsepower per hour. calculate the following:
1: maximum velocity at sea level.
2: the maximum range
3: the maximum endurance
Answers
The maximum velocity at sea level can be found using the following equation:
V_max = sqrt((2 * W) / (rho * S * CL_max))
where:
W = maximum weight = 1020 kgf
rho = air density at sea level = 1.225 kg/m^3
S = wing area = 11.45 m^2
CL_max = maximum lift coefficient = (2 * W) / (rho * V^2 * S)
To find CL_max, we need to assume a value for the velocity V and iterate until convergence. Let's start by assuming V = 70 m/s:
CL_max = (2 * 1020 kgf) / (1.225 kg/m^3 * (70 m/s)^2 * 11.45 m^2) = 1.87
Now we can use this value to find the maximum velocity:
V_max = sqrt((2 * 1020 kgf) / (1.225 kg/m^3 * 11.45 m^2 * 1.87)) = 35.5 m/s
Therefore, the maximum velocity of the Predator UAV at sea level is approximately 35.5 m/s.
Maximum Range:
The maximum range can be found using the following equation:
R = (L/D) * (1/OE) * ln(Wi/Wf)
where:
L/D = lift-to-drag ratio = CL / CD
CL = lift coefficient = W / (0.5 * rho * V^2 * S)
CD = drag coefficient = CD_0 + (CL^2 / (pi * e * AR))
CD_0 = zero-lift drag coefficient = 0.03
e = Oswald efficiency factor = 0.7
AR = aspect ratio = (wingspan)^2 / S
OE = overall efficiency = propeller efficiency * engine efficiency
propeller efficiency = 0.9
engine efficiency = 0.85 (assuming 85 horsepower for the engine)
Wi = initial weight = maximum weight + fuel weight = 1020 kgf + 295 kgf = 1315 kgf
Wf = final weight = maximum weight
We can start by assuming a value for the velocity V and iterating until convergence. Let's start with V = 25 m/s:
CL = 1315 kgf / (0.5 * 1.225 kg/m^3 * (25 m/s)^2 * 11.45 m^2) = 1.67
AR = (14.85 m)^2 / 11.45 m^2 = 19.3
CD = 0.03 + (1.67^2 / (pi * 0.7 * 19.3)) = 0.071
L/D = 1.67 / 0.071 = 23.5
OE = 0.9 * 0.85 = 0.765
R = 23.5 * (1/0.765) * ln(1315 kgf/1020 kgf) = 393 km
Now we can try a different value for V, let's say V = 30 m/s:
CL = 1315 kgf / (0.5 * 1.225 kg/m^3 * (30 m/s)^2 * 11.45 m^2) = 1.24
AR = (14.85 m)^2 / 11.45
A producer is someone who _____________.
A.
Makes a commodity available for sale or exchange
B.
Buys or trades in order to receive a commodity
C.
Is in the market for a commodity
D.
Receives a commodity from a business
Answers
Answer: A. Makes a commodity available for sale or exchange
Explanation: hope it helps ^w^
rocks AND minerals aré natrally ocurring substaces
Answers
Answer:
yes they are naturally occurring substances.
Answer:
Explanation:where’s the question love?
when using emt type conduit splices and taps shall be
Answers
When using EMT type conduit splices and taps shall be made with separate couplings.
EMT type conduit splices and taps shall be made with separate couplings. This is done to ensure safety and stability when the conduits are used.
Splices and taps in EMT conduits must be made using separate couplings.
The EMT or electrical metallic tubing is a metallic raceway that is commonly used in the electrical industry. It is made from thin-walled galvanized steel and has a protective coat that protects it from corrosion.
Its main purpose is to protect wires and cables that are placed inside it from physical damage and also protect people from the current carrying wires.
The EMT conduits are connected together using couplings which are the most common way of connecting conduit sections. In case the conduits are joined with connectors, the joints can be very weak, which may result in electrical arcing. Therefore, it is not advisable to use connectors while joining EMT conduits.
A proper installation of the EMT conduits requires proper joining of the conduit sections. Splices and taps in EMT conduits must be made using separate couplings.
To know more about Splices:
https://brainly.com/question/31939873
#SPJ11
There are withdrawn 100 ft3
of air measured at 30 psia and 90°F from a 50 ft3
tank containing air
initially at 100 psia and 140°F. What is the pressure of the air remaining in the tank if its
temperature is 130 °F?
Answers
Answer:
2+2g
what time is good afternoon my
Determine the enthalpy, volume and density of 1.0 kg of steam at a pressure of 0.5 MN/m2 and with a dryness fraction of 0.96
Answers
Answer:
Enthalpy, hsteam = 2663.7 kJ/kg
Volume, Vsteam = 0.3598613 m^3 / kg
Density = 2.67 kg/ m^3
Explanation:
Mass of steam, m = 1 kg
Pressure of the steam, P = 0.5 MN/m^2
Dryness fraction, x = 0.96
At P = 0.5 MPa:
Tsat = 151.831°C
Vf = 0.00109255 m^3 / kg
Vg = 0.37481 m^3 / kg
hf = 640.09 kJ/kg
hg = 2748.1 kJ/kg
hfg = 2108 kJ/kg
The enthalpy can be given by the formula:
hsteam = hf + x * hfg
hsteam = 640.09 + ( 0.96 * 2108)
hsteam = 2663.7 kJ/kg
The volume of the steam can be given as:
Vsteam = Vf + x(Vg - Vf)
Vsteam = 0.00109255 + 0.96(0.37481 - 640.09)
Vsteam = 0.3598613 m^3 / kg
From the steam table, the density of the steam at a pressure of 0.5 MPa is 2.67 kg/ m^3
A coastal engineer is to an oil platform as a structural engineer is to:
a freeway.
a skyscraper.
submarine pipelines.
an underground tunnel.
Answers
Answer:
I think the answer is d: underground tunnel
Explanation:
Hope this helps
Advise a suitable structural form for the 50-storey residential
towers to resist strong lateral wind load.
Answers
A suitable structural form for the 50-storey residential towers to resist strong lateral wind loads is a reinforced concrete shear wall system. This system involves the use of vertical concrete walls distributed throughout the building's floor plan. These walls act as the primary structural elements that resist the lateral forces generated by strong winds.
The reinforced concrete shear wall system offers several advantages in terms of lateral stability and wind load resistance. The vertical walls provide stiffness and strength to counteract the lateral forces, effectively reducing the building's sway and minimizing the potential for structural damage. The system also offers good structural integrity, durability, and fire resistance.
In addition to the shear walls, other complementary structural elements such as floor diaphragms, columns, and foundation systems are incorporated to ensure overall stability and load distribution. Proper structural analysis and design, including consideration of wind load effects and local building codes, are crucial to ensure the towers can withstand the anticipated wind forces.
It is important to note that structural design considerations should involve the expertise of professional structural engineers who will assess the specific site conditions, wind loads, and architectural requirements to determine the most appropriate structural form for the 50-storey residential towers.
Learn more about load resistance here:
https://brainly.com/question/30514230
#SPJ11
On-vehicle headlight aligners are calibrated to the floor at the point where the _______ wheels contact the concrete.
Answers
On-vehicle headlight aligners are calibrated to the floor at the point where the alignment wheels contact the concrete.
What is calibration in wheel alignment?Wheel alignment is known to be n aspect of standard automobile maintenance that is known to be made up of adjusting the angles of the wheels so that it can be able to set to the car in regards to the maker's specification.
Hence, based on the above, On-vehicle headlight aligners are calibrated to the floor at the point where the alignment wheels contact the concrete.
Learn more about Wheel alignment from
https://brainly.com/question/4070517
#SPJ1
Assuming you determine the required section modulus of a wide flange beam is 200 in3, determine the lightest beam possible that will satisfy this condition.
Answers
Answer:
W18 * 106
Explanation:
Given that the section modulus of the wide flange beam is 200 in^3 the lightest beam possible that can satisfy the section modulus must have a section modulus ≥ 200 in^3. also the value of the section modulus must be approximately closest to 200in^3
From wide flange Beam table ( showing the section modulus )
The beam that can satisfy the condition is W18 × 106 because its section modulus ( s ) = 204 in^3
1. The term lefty loosey, righty tighty is used to prevent what?
Answers
Answer:
Used to recall the direction a standard screw
match the standards of iso 9000 (in the left column) with the respective industry-specific interpretations of iso 9000 (in the right column).
Answers
An ISO 9000-certified firm will create "excellent" goods or services, according to the standard. Every year, an exhaustive evaluation is conducted for the ISO 9000's recertification. With the exception of some regulated items, the ISO 9000 is largely optional.
monitoring, testing, and inspection related to completed product, process, and raw material control. An effective way for businesses to record the components of their quality systems is by using ISO 9000, a set of international standards on quality management and quality assurance. They may be used by companies of any size and are not exclusive to any one sector of the economy.4 Conformance. Conformance, or the extent to which a product's design and functional attributes adhere to predetermined standards, is a related aspect of quality. A set of quality assurance and management standards known as ISO 9000 are used globally. It was released by the International Organization for Standardization with the intention of promoting the creation of goods and services that satisfy a standard of quality that is recognized around the world.
To learn more about ISO 9000 click the link below:
brainly.com/question/6188356
#SPJ4
a 12-bit converter has an input range of /- 10 v and is connected to amplifier with following gains: 1, 10, 100 and 500. the connected sensor has maximum output of 7.5 mv. select appropriate gain to minimize the quantization error. calculate percentage quantization error for the maximum input.
Answers
Maximum quantization error is calculated using the formula Maximum quantization error = (VH - VL)/2(2n), where n is the ADC's resolution in bits.
The largest inaccuracy that can occur corresponds to a voltage that is (1/2) of an LSB. This quantization would be the sole cause of error in the recorded samples for a perfect digital recorder. This mistake establishes the absolute upper bound on the readings' accuracy for a real digital recorder. The difference between the analog signal and the nearest available digital value at each sampling instant from the A/D converter is known as the quantization error. Quantization error also introduces noise to the sample signal known as quantization noise.
Learn more about value here-
https://brainly.com/question/29053888
#SPJ4
Explain any three ways research can facilitate the work of building technicians
Answers
According to the research, research can facilitate the work of building technicians in the conception, materials to use and planning of the project.
What are building technicians?They are experts in construction projects, supporting the design of plans, estimating costs, planning work methods, etc.
Research can facilitate the work of building technicians in the following ways:
Conception, design and planning of the project.Selection of materials for floor, wall and ceiling systems.Carry out the programming of works, budgets and analysis of unit prices.Therefore, we can conclude that according to the research, research can facilitate the work of building technicians in the conception, materials to use and planning of the project.
Learn more about construction projects here: https://brainly.com/question/17083292
#SPJ1
25 In differential aeration corrosion, rich oxygenated parts are
(a) anodic(b)cathodic
(c) protected (d) none of above
26
To eliminate entrapment of moisture, it is advised to
(a) make corners smooth
(b) coat the containers
(c) use corrosion resistant alloy, like cupro-nickel (d) provide a drainage hole
27 Storage containers should be designed in such a way that
(a) No crevices are formed
(b) No obstacle to drainage occurs
(c) The design should ensure that the containers are drained in minimum time
(d) the containers should be constructed from plastics rather than metals or allows
28 The corrosion resistance of metals, such as stainless steels and copper alloys.
depends upon the buildup of uniform surface films. Which one of the following
would require a maximum attention of the designer?
(a) Accessibility of oxygen in the operating medium.
(b) Coating of the metal
(c)The drainage capability of the vessel (d)
The period of storage of the liquid in the container
Answers
Answer:what are you trying to say
Explanation:
Calculate the power required for heating a 1.5 kg sample of water for 10 minutes in a thermal system. What is the amount of energy required to raise the temperature of the water from 25°C to 60°C ? How much minimum amount of power does the heater have to supply per unit time? Why does the actual power rating of the heater need to be higher than this minimum amount? (The specific heat of water is 4.18 J/g°C .)
*60 points to anyone who can help*
Answers
Answer:
Power= Heat energy\ time
heat energy= mc∆T
specific heat of water = 4180
1.5*4180*(60-25)
=219450
time = 10× 60= 600 secs
power = 219450/600
Power= 365.75 Watt
=0.37 KW
Explanation:
the actual has to be bigger because the heater might be required to handle more ...also to accommodate extra energy.
Review the following statements and select the most appropriate answer.
Statement one
The site specification for construction work to be undertaken on site would provide information on he general safety requirements for scaffolds on building sites
Statement two
The Construction (Health, Safety and Welfare) Regulations 1996 should be used as a source of
reference for scaffolding information
a) Statement one is correct and statement two is incorrect
b) Statement one and two are correct
c) Statement two is correct and statement one is incorrect
d) Both statements are incorrect
Answers
The most appropriate answer to this question is option B. Statement one and two are correct.
This is option B
The site specification for construction work to be undertaken on site would provide information on the general safety requirements for scaffolds on building sites. This statement is correct. A site specification is a document that outlines the requirements for a construction project.
The Construction (Health, Safety and Welfare) Regulations 1996 should be used as a source of reference for scaffolding information. This statement is also correct. This act provides the framework for ensuring the health, safety, and welfare of all construction workers.
The act requires that contractors ensure that work is carried out safely, that appropriate precautions are taken, and that safety standards are maintained.Based on the given statements, statement one and statement two are both correct. Therefore, option B is the correct answer.
Learn more about scaffold at
https://brainly.com/question/29237786
#SPJ11
What is the largest size (mm) internal through crack that a thick plate of aluminum alloy 2024-T851 can support at an applied stress of:
Answers
The given aluminum alloy is 2024-T851, the largest size (mm) internal through crack that it can support at an applied stress of 42 MPa is required.
The calculations are as follows.The aluminum alloy 2024-T851's yield strength is σy = 510 MPa. Therefore, the stress intensity factor can be computed using the following formula:K1C = σ √(πa)K1C = (510/√2) √(πa)Given σ = 42 MPa, the above formula simplifies to:42 × 10^6 = (510/√2) √(πa)πa = [42 × 10^6 / (510/√2)]^2πa = 247.51 mm^2a = (247.51/π)a = 78.8 mm
Therefore, the largest size (mm) internal through crack that a thick plate of aluminum alloy 2024-T851 can support at an applied stress of 42 MPa is 78.8 mm.
To know more about factor visit:
https://brainly.com/question/14452738
#SPJ11
Give an example of one technology that is well matched to the needs of the environment, and one technology that is not.
Answers
Answer:
oh god... i have no idea lm.ao
Explanation:
A comparison of parking fee changed at 4 randomly selected parking areas were 12 15 17 and 20 pesos per car find the mean the variance of the parking fees
Answers
The calculated mean value is 16. The sum of all values divided by the total number of values determines the mean (also known as the arithmetic mean, which differs from the geometric mean) of a dataset.
The term "average" is frequently used to describe this measure of central tendency. By dividing the sum of the given numbers by the entire number of numbers, the mean—the average of the given numbers—is determined. Mean is equal to (Sum of All Observations/Total Observations).
Mean=12+15+17+20/4
=16
Special road signage designate 10-cent zones. At the beginning and finish of the zone, there are signs. There is one space available for as long as three or four hours each day. Only specific hours of the day are subject to the 10 cent rate. There may be a Blue Zone in locations where paid parking is not (yet) in effect.
Learn more about mean here-
https://brainly.com/question/14882017
#SPJ4
A wind tunnel is used to study the flow around a car. The air is drawn at 60 mph into the tunnel. (a) Determine the pressure in the test section as determined by the manometer. (b) Determine the pre
Answers
Answer:
The answer is below
Explanation:
The complete question is attached.
a) Bernoulli equation is given as:
\(P+\frac{1}{2}\rho V^2+ \rho gz=constant\\\\\frac{P}{\rho g} +\frac{V^2}{2g} +z=constant\\\)
Where P = pressure, V = velocity, z = height, g = acceleration due to gravity and ρ = density.
\(\frac{P}{\rho g} +\frac{V^2}{2g} +z=constant\\\\\frac{P}{\gamma} +\frac{V^2}{2g} +z=constant\\\\\frac{P_1}{\gamma} +\frac{V_1^2}{2g} +z_1=\frac{P_2}{\gamma} +\frac{V_2^2}{2g} +z_2\\\\but \ z_1=z_2,P_1=0,V_1=0,V_2=60\ mph=88\ ft/s. Hence:\\\\\frac{P_2}{\gamma} =-\frac{V_2^2}{2g} \\\\P_2=\gamma*-\frac{V_2^2}{2g} =\rho g*-\frac{V_2^2}{2g} \\\\P_2=-\frac{V_2^2}{2}*\rho=-\frac{(88.8\ ft/s)^2}{2} * 0.00238\ slug/ft^3=-9.22\ lb/ft^2\\\\P_2+\gamma_{H_2O}h-\gamma_{oil}(1/12 \ ft)=0\\\\\)
\(\gamma_{oil}=0.9\gamma_{H_2O}=0.9*62.4\ lb/ft^3=56.2\ lb/ft^3\\\\Therefore:\\\\-9.22\ lb/ft^2+62.4\ lb/ft^3(h)-56.2\ lb/ft^3(1/12\ ft)=0\\\\h=0.223\ ft\)
b)
\(\frac{P}{\gamma} +\frac{V^2}{2g} +z=constant\\\\\frac{P_2}{\gamma} +\frac{V_2^2}{2g} +z_2=\frac{P_3}{\gamma} +\frac{V_3^2}{2g} +z_3\\\\but \ z_3=z_2,V_3=0,V_2=60\ mph=88\ ft/s. \\\\\frac{P_2}{\gamma}+\frac{V_2^2}{2g} = \frac{P_3}{\gamma}\\\\\frac{P_3-P_2}{\gamma}=\frac{V_2^2}{2g} \\\\P_3-P_2=\frac{V_2}{2g}*\gamma=\frac{V_2^2}{2g}*\rho g\\\\P_3-P_2=\frac{V_2}{2}*\rho=\frac{(88\ ft/s^2)^2}{2}*0.00238\ slg\ft^3\\\\P_3-P_2=9.22\ lb/ft^2\)
Warning danger ahead sign
Answers
Answer: okiiiii
Explanation:
Ok
Explanation
What is the purpose of making internal resistance of milli-ammeter very low?A) High accuracy.B) Minimum voltage drop across meter.C) Maximum voltage drop across meter.D) High sensitivity.
Answers
Answer:
B) Minimum voltage drop across meter
Explanation:
An ammeter is a measuring instrument device that is used to measure small currents flowing through a circuit in milli-ampere. The internal resistance of the milli ammeter is very low so that there would be a minimum voltage drop across the meter causing a minimum effect of the current in the circuit, this results to a measurement closer to the original value. If a high resistance is place, there would be large voltage drop therefore the current measured would be lesser than the original value.
Why is a straight-bladed spatula used for mixing impression material on a mixing pad, but not in a rubber bowl?
Answers
A straight-bladed spatula is used for mixing impression material on a mixing pad, but not in a rubber bowl because it is iron and constant use may destroy the rubber.
What is the aim of a straight edge spatula?The term Straight edge is known to be a kind of a metal spatula that is known to have a long flat spatula.
It is one that is also known to have a straight edge that is said to be used for leveling or used in working of frosting cakes.
Note that the Strainer - wire mesh helps to move or separates liquids from food.
Hence, A straight-bladed spatula is used for mixing impression material on a mixing pad, but not in a rubber bowl because it is iron and constant use may destroy the rubber.
Learn more about spatula from
https://brainly.com/question/25252798
#SPJ1
Technician a s ays both an ohmmeter and a self-powered test light may be used to test for continuity. technician b says both may be used to test fuses. who is correct?
Answers
Both technicians A and B are accurate since, in technician B's opinion, both may be employed to test fuses.
What is continuity?Continuity describes how a function behaves at a specific point or portion. Continuity can be determined using the limit.
We can infer from the question: The expert says you can test for continuity with an ohmmeter and a self-powered test light. Technician B said that both may be used to test fuses.
As a result, both technicians A and B are accurate because, in technician B's opinion, both may be employed to test fuses.
The complete question is:
Technician A says both an ohmmeter and a self-powered test light may be used to test for continuity. Technician B says both may be used to test fuses. Who is correct?
Learn more about the continuity here:
https://brainly.com/question/15025692
#SPJ1